Answered: The ratio between maximum discharge and…

The ratio between maximum discharge and top width of a rectangular channel is 1.82. Calculate the water depth if the bed slope is 1 in 3000. Use Chezy equation and C = 50

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Given the following data for a stream of uniform flow: A = 8.98 sq.m. (average stream cross section)…

A: Given data, A = 8.98 m² P = 10.76 m S = 0.008 n = 0.020 To find out the hydraulic radius of…

Q: using Kennedy's theory, if the depth of flow Calculate the critical velocity (m/sec) of a channel is…

A: Given data- depth of flow y=3 mTo Find-The critical velocity Vc

Q: 3. The Hydraulic Depth of a triangular channel is 5m, calculate the normal depth of the channel. a)…

A: The Hydraulic Depth of a triangular channel is 5m, calculate the normal depth of the channel. a) 8m…

Q: A channel having a cross-section shown below has a flow rate of 0.049 m^3/s. Compute the hydraulic…

A: Hello dear, The answer is found to be Hydraulic radius R=1.845 m For explanation please see the…

Q: 7. Refer to the following channel cross section. (a) What is the normal depth? (b) What is the…

Q: Determine the normal depth (m) in a rectangular channel with flowing discharge of 70 m3/s, roughness…

A: B=6m n=0.025 Q=70 cumec

Q: A 4.88 m deep, clean-earth river (n = 0.03) has a flow rate q = 13.01 m3/s/m. Compute the velocity,…

Q: Determine the Hydraulic Radius for the given Open Channel in terms of meter. -0.52 m e = 60° b= 0.8…

Q: A trapezoidal channel with uniform flow depth 4 m. The base width is 6 m and the side slopes are…

A: For different surfaces Manning's roughness coefficient is given. It is required to find weighted…

Q: Water Resources Engineering: Open Channel Flow Determine the cross section (i.e. find the slope,…

A: The trapezoidal section is shown below:

Q: If the channel shown in cross-section the runoff coefficient is 0.02 and has slope of (12 cm per 1…

A: Given Data: Runoff coefficient is n=0.02. Slope of the channel is S0 S0=12 cm1 km=12 cm1×1000×100…

Q: length of sharp-crested rectangular weir (w/ end contractions) = 2 m Q = 0.89 m^3/s What is the…

A: Given : Rectangular sharp crested weir with end contractions. Length of weir, L = 2 m Discharge,…

Q: In a circular channel 3.0 meters in diameter, flowing over half full, the water surface width is…

A: Hi there! Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: The following figure shows and inclined aquifer at 100 to the horizontal. The difference in water…

A: k=0.7mm/sec h=5m Theta= 10o Discharge is given by q=kia where, k= hydraulic conductivity i=…

Q: Design an irrigation channel by Kennedy’s theory to carry 5 cumecs of discharge with critical…

Q: The Hydraulic diameter of a equilateral triangularchannel is 5 cm, the side length is 10cm. The…

A: The given data is as follows: For an equilateral triangular channel,Hydraulic diameter=5 cmSide…

Q: 5. The ratio between hydraulic radius and hydraulic depth of a triangular channel is 31/100,…

A: Please refer the attached image for complete solution. THANK YOU.

Q: Determine the bed slope of a rectangular channel 5 m wide and 2 m deep. The discharge is recorded as…

A: Given: Width of channel, b = 5 m Depth of channel, d = 2 m Discharge, Q = 20 m3/s Chezy's constant,…

Q: Hydraulic mean depth of a rectangular channel having Width as 2 m and flow depth 50 cm 0.333 0.222

A: H=Wetted AreaWetted PerimeterWetted Area=2m×0.5m=1m2Wetted Perimeter=0.5×2+2=3m

Q: The bed width of a trapezoidal channel is 5.0 m, 5,= 0.0004, the side slope is m = 2 horizontal: 1…

Q: The critical velocity ratio for a depth of flow 2.5 m in alluvial channel is 1.25. If the manning's…

Q: Consider a regime channel to carry a discharge of 36 m³/s and has a mean velocity of 0.9 m/s. Find…

Q: If the water depth immediately upstream or downstream of the hydraulic jump in a rectangular channel…

A: V=1m/s To find conjugate depth

Q: Calculate the hydraulic mean radius Manning's equation for a trapezoidal channel to carry 200 cumec…

Q: in a wide rectangular channel if the normal depth is increased by 20%,find the percentage increase…

A: Given : Normal depth is increased by 20 %. Percentage increase in discharge = ?

Q: ater flows in a 1.5-m wide rectangular channel with a constant bed slope So = 0.19. The…

A: In this question we will firstly find the area of the bed. Then we will calculate the value of the…

Q: Compute the hydraulic radius for the channel shown in if the water depth is 2.50 m, in meters to the…

A: Given:- Water depth=2.5 mSlope, S=0.75 % =0.7510000 =75×10-4Manings…

Q: The critical velocity ratio for a depth of flow 2.5 m in alluvial channel is 1.25. If the manning's…

Q: EXAMPLE 1: Determine the normal discharge for the channel shown in Fig 2.7a. The water surface in…

A: Flow in most channels is turbulent, and laminar flow in open channels is very rare. Laminar…

Q: The flowrate per unit width (q = Q/b) in a wide rectangular channel is q = 4 m2/s. Is the flow…

A: q (flow per unit width) = 4 m2/s

Q: he ratio between discharge and top width of a best draulic rectangular channel is 91/50, calculate…

Q: An alluvial channel is carrying a discharge of 5 m³/s at a bed slope of 1 in 1400. The velocity of…

Q: Example: Compute the normal depth in a trapezoidal channel having a bottom-width of 10 m, side…

A: Using the Mannings formula to determine the normal depth in the trapezoidal channel section.…

Q: Example: A 4.5-m wide trapezoidal channel having a side slope of 1.5 horizontal: 1 vertical is laid…

A: Given: The bottom width is 4.5 m. The side slope is 1.5H:1V. The bed slope is 0.00035. The discharge…

Q: Calculate the value of the Chezy’s constant. For a bed slope of 1/2500, find the flow rate.

A: Hydraulic radius is R=Wetted AreaWetted perimeterWetted Area=B×y=3×1=3m2Wetted…

Q: A trapezoidal channel has a bottom width of 6.0m, side slopes of 2 vertical: 4 horizontal, and…

A: Bottom Width (B)=6m Side Slope(1:n)= Vertical:Horizontal n=42 n=2 Discharge(Q)=17m3/s channal bed…

Q: The ratio between discharge and top width of a best hydraulic rectangular channel is 91/50,…

Q: A rectangular open channel, with a constant discharge of 32m3/s, has a smooth expansion from (1) to…

A: Given that, Constant discharge (Q)=32 m3/sec. Consider B1=3.6 m, y1=2.4 m Using the continuity…

Q: A very wide rectangular channel is designed to carry a discharge of 5 m³/s per meter width. The…

Q: 3.1) The channel with a cross-section shwn in Figure 4 has an n-coefficient of 0.015 and a bottom…

A: Schematic representation of the given problem:

Q: Q1: Design an earthen channel which has a trapezoidal cross section with a bed width equal to 12…

A: Introduction : When the slope of the water surface and channel bottom is the same and the water…

Q: Problem 3 Determine the slope of the bed of a rectangular channel of width 6 m and depth of flow 3…

A: Given data-

Q: Question 10 Determine the normal depth (m) in a rectangular channel with flowing discharge of 80…

A: Discharge, width, manning’s roughness and slope has been given and it has been asked to determine…

Q: Consider the uniform flow of water in the triangular channel shown in the figure. The channel bed…

Q: A trapezoidal channel with uniform flow depth 4 m. The base width is 6 m and the side slopes are…

A: Given that: Base width, B = 6m, Water depth, y=4m

Question

None

The ratio between maximum discharge and top
width of a rectangular channel is 1.82.
Calculate the water depth if the bed slope is 1
in 3000. Use Chezy equation and C = 50
Оа.
y=1.24m
O b. y=2m
Ос.
O C.
y=2.9m
o d. y=0.73m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

.Determine the critical depth in meters for Trapezoidal channel. Base width = 5m Side Slope 2H:3V Discharge = 160 m3/s
For a V-shaped concrete lined channel with total included angle of 80°, and a depth of 3 m if the discharge is 10.7 m^3/s. Determine the slope if Bazin’s constant is 1.54( final answer must be in fraction i.e. 1/50)
(c) Determine the downstream depth, y2(d) Determine the absolute change in the water surface from location 1 to location 2.
A trapezoidal section of 2 m bottom width, carries a discharge of 4 M3/s. The channel’s raughness is 0.025. What is the condition of the best hydraulic section to calculate the channel bottom slope?
An unsymmetrical trapezoidal channel with one side inclined from horizontal by 35 degree and the other inclined from vertical by 40degree is to be designed to carry a 2.0 cubic meters per second discharge. Determine the dimensions of the channel for most efficient section if roughness coefficient is 0.030 and average longitudinal slope is 0.05. Draw the cross section of the open channel considering the freeboard height. Use Chezy and Kutter’s C formula.
The side slope of a trapezoidal open channel are 1 horizontal to 1.75 vertical. The bottom width is 2.5m and length of flow is 3m. The coefficient of roughness n=0.015 and the slope of the channel bed is 0.0004. Calculate the velocity of flow (m/s) using Manning's formula. Round answer to one decimal place.
A trapezoidal channel with side slope of 2H-1V has a flow rate of 160 m3/s and depth of 4 meters. The slope is 1m per kilometer. Determine corresponding bottom width in meters. Answer pls
find the length of the water profile for a wide rectangular that has a bed slopeof 7.5 cm/km and carries a discharge of 2.5 m2/s. The channel terminates intosudden fall., assuming a critical depth at the sudden fall is 0.612 m. Take the Chezycoefficient as 35 (metric)
Design a straight trapezoidal erodible channel that can carry a discharge of 12.5m^3/s using tractive force method based on the following information. The side slope is 1V:4H The bottom slope is 0.0015 The manning's roughness coefficient is 0.024 The critical shear stress as 7.2KN/m^2 Angle of repose is 23 Density of water 1000kg/m^3
An unsymmetrical trapezoidal channel with one side inclined from vertical by 35o and the other inclined from horizontal by 40o is to be designed to carry a 2.5 cubic meters per second discharge. Determine the dimensions of the channel for most efficient section if roughness coefficient is 0.025 and average longitudinal slope is 0.05. Draw the cross section of the open channel considering the freeboard height. Use Chezy and Kutter’s C formula.
The bottom width of a trapezoidal canal is 2.5m and its sides are both inclined at 60 degree with the horizontal. Water flows at a depth of 3m. Calculate the discharge of the slope of the canal is 0.0008 with a coefficient of roughness n=0.03
What is the depth of water in a trapezoidal channel with z = 2.0 and carrying 2.5 cubic meter per second of water flow? The channel’s bottom width is 2.5 m and the velocity of flow is 0.9 m/s.