The shovel of an end loader has pins at points A, B, C , and D. The scoop supports a downward vertical load of 4,400 lb, which is not shown in the figure, at point E. Determine the force the hydraulic cylinder AD must generate to keep the shovel in equilibrium in lb.

Q: The Super Soaker XP30 is a marvel of hydraulic dispersion weaponry. By pumping on the handle, you…

A: Given data:- Density of water =1000 kg/m3  chamber pressure P1 = 697500 Pascals (absolute) y1 =…

Q: The parameter of a single-degree-of-freedom system are given by m=1 kg, c=5 N-sec/m, and k=16 N/m.…

A:

Q: If the Radius of a elbow is 6”, and the duct Diameter is 3”, what is the loss factor if the elbow is…

A: Given data :- the Radius of an elbow (R)= 6 in the duct Diameter (D) =3 in To find :- the loss…

Q: A swimming pool Wby Y by h deep is to be emptied by gravit Assuming an average pipe friction factor…

A: Fluid dynamics are represented by Bernoulli's theorem. The total energy in the system remains…

Q: 3. Air is contained within a piston-cylinder assembly The cross sectional area of the piston is 0.01…

A:

Q: Professor Modyn wants to power his refrigerator with a heat engine. A Carnot heat engine receives…

A:

Q: Calculate the bending moment at C to one decimal place (e.g. 35.0) Mc = Blank 1 kNm 20 KN I A B form…

A: Detailed explanation and solution of the above problem uploaded in below picture.

Q: Consider the water jet moving at 12.8 m/s (see Figure Q1). The water jet is split so that one-third…

A: For water, ρ=1000kg/m3A=π4d2=π40.0352=9.62×10-4m2v=12.8 m/su=v0= m/s Here, as splitter is also…

Q: what is ve stands for?

A: While applying Varignon's theorem about point A, the expert uses sign convention for moment.…

Q: A diesel power plant has an overall efficiency of 30%. If the calorific value of diesel is 18000…

A:

Q: A 2.25 kN m torque is applied to the solid cylinder made up of a hollow cylinder and an inner core…

A:

Q: 12.0 N 30.0% b 10.0 N 9.00 N The figure shows one cylinder inside another. The inner cylinder has a…

A: Given,

Q: A solid aluminum shaft 2 in. in diameter is subjected to two torques as shown in the figure.…

A:

Q: What is the role of the fin(s) in heat transfer? What is the definition of fin efficiency? What are…

A:

Q: The time required to saw a rectangular piece of stainless steel plate 3.5 meters long and 2.25…

A:

Q: An ideal gas passes a diffuser. At the diffuser inlet, the temperature is T1 = 350.00 K, the…

A: Given        Pressure, P1 = 100 kPa  Temperature, T1 = 350 K   Gas constant, R = 0.287 kJ/kg.K Find…

Q: Grip. In the engineering design of handles (such as on manual and powered hand tools) and rails…

A: For solution refer below images.

Q: Example For the position of the mechanism shown in Fig. (a), calculate the angular velocity of the…

A:

Q: In statics of rigid bodies, the calculation of multiplying three vectors together using both the dot…

A: Given data:- For rigid body in statics Vector A=ai+cj B= Bi+aj-ck C=ci-aj+bk To find:-  Scalar…

Q: you stand at rest on a bench, the bench exerts a normal force on you, equal and opposite to your…

A:

Q: 4. Give an order of magnitude estimate (stating all of your assumptions) of the shear stress on the…

A:

Q: A heat pump system operates between temperature limits of -5 and 18°C. The heating load of the space…

A:

Q: Which of these are the steps involved in Deming's wheel (PDCA) plan, do, check, analyse Oplan,…

A:

Q: As shown below, the 10 kg ball C attached to rod AB is released from rest when 0 = 0° and the…

A:

Q: An object on a rope is lowered at a steadily decreasing speed. Why is the rope tension greater than…

A:

Q: Pb 5 Dtetermine MOI of "T" shape beam with respect to base x and y (Ix and Iy) I¸=I₂+A(d,…)², I₂ =…

A: Given,

Q: The time required to saw a rectangular piece of stainless steel plate 3.5 meters long and 2.25…

A:

Q: A tensile test is conducted for a metal wire which has a diameter of 4.5, the maximum recorded force…

A:

Q: What are the process of taper turning?

A: Taper turning:  In typical straight turning, the cutting tool goes along a path parallel to the…

Q: A thin-walled double pipe counter flow heat exchanger is used to cool oil (c= 2.20 kJ/kgK) from…

A: Given: CO=2.20KJ/KgKmO˙=2Kg/sTO,i=150oCTO,o=40oCCW=4.18KJ/KgKmw˙=1.5Kg/sTW,i=22oC

Q: Problem 2.151: Energy Dissipated in Viscous Damping Find the energy dissipated during a cycle of…

A:

Q: Air at standard pressure and temperature is permitted to expand adiabtically when the temperature is…

A: Given: Air at standard pressure and temperature is permitted to expand adiabtically when the…

Q: E דך 74 360 mm 450 mm 60° B, 002 D OC = 140 mm AD = 800 mm DE = 250 mm ₂= 21 rad/s B on slider C on…

A:

Q: 2. Solve the differential equation by separation of variables: dy y dr X

A:

Q: Example For the position of the mechanism shown in Fig. (a), calculate the angular velocity of the…

A:

Q: (type 304) fin of th ned to a 1 cm OD tube. The fin is surrou cient of 40 W/m2K. The tube wall temp…

A: Given data as per questionAn annular stainless steel (type 304) fin Thickness, t=4 mm=0.004 m…

Q: What is the difference between sandy plumbing and streamlined plumbing?

A:

Q: 4) Calculate the final temperature of water if you mix one liter of water at 40 °C with two liters…

A: Given: The density of the water→ρ=1000 Kg/m3 One liter of water at→T1=40°C Volume of the one liter…

Q: A tensile test is conducted for a metal wire which has a diameter of 4.5, the maximum recorded force…

A: Given , Diameter (D) = 4.5 mm Maximum force (F) = 3700 N It is asked to find UTS point.

Q: 6.92* At a particular axial position, the beam whose cross section is shown is subjected to a shear…

A: Given         Shear force, V = 40 kN   Inner diameter, d = 50 mm Outer diameter, D = 80 mm Find…

Q: For a short time, gear A of the automobile starter rotates with an angular acceleration of α₁ (450+²…

A:

Q: It consider that three bars should attain horizontal level in Figure while subjected to tensile…

A: Given DataσA=300×103 MPaσB=200×103 MPaLA=LC=150mmA=25mm2

Q: An inclined tank contains three different liquids A, B and C with specific gravities of 0.80, 1.00…

A:

Q: Differentiate between saturated liquid and saturated vapor. Make use of T-S diagram along with your…

A: It is required to differentiate between the saturated vapour and saturated liquid states.

Q: When the slider block C is in the position shown in (Figure 1), the link AB has a clockwise angular…

A: Using I - centre method

Q: 3. Compute for the Break Mean Effective Pressure with the following information: Given: Bhp = 1000…

A:

Q: Problem 2.173: Coulomb Damping A mass of 20 kg is suspended from a spring of stiffness 10,000 N/m.…

A:

Q: A circular pipe flow, the diameter d=50mm, mean velocity of water flow in the pipe v=1.5m/s,…

A:

Q: For a short time a motor of the random-orbit sander drives the gear A with an angular velocity of…

A: Given data: ωA=40t3+6tt=2.3 s

Q: A stepped solid shaft ABC is fixed at points A and C and is subjected to two external torques equal…

A: Given data:- stepped solid shat ABC T0 =10 Kip-in d1=1 in d2=1.45 in Length of AB = Length of BC =…