Question

The thermal voltage for a on junction diode is 350 mv. What will be temperature in centigrade?

Expert Answer

Want to see the step-by-step answer?

Check out a sample Q&A here.

Want to see this answer and more?

Experts are waiting 24/7 to provide step-by-step solutions in as fast as 30 minutes!*

*Response times may vary by subject and question complexity. Median response time is 34 minutes for paid subscribers and may be longer for promotional offers.
Tagged in
Engineering
Electrical Engineering

Analog Electronics

Related Electrical Engineering Q&A

Find answers to questions asked by students like you.

Q: Determine the Lorentz force experienced by a point charge of Q = 6x10-16C moving in a combined field...

A: Click to see the answer

Q: two resistors are connected in parallel, one has 2 ohm in value and the other is twice as greeat as ...

A: One resistor is 2 ohms and another one is twice of first one I.e 2×2=4ohms and these two are connect...

Q: State and establish the time shifting property of Laplace Transform.

A: The time-shifting property of Laplace transform has been discussed and established in the following ...

Q: he network in the Figure below operates at 60 Hz. Compute the energy stored in the mutually coupled ...

A: Click to see the answer

Q: 1- Aşağıda verilen elektrik devresine ilişkin: i(t) R e(t) a) R=5 ohm, L=1_mH, C=2 mF olmak üzere, d...

A: Click to see the answer

Q: Please provide long discriptive answer on given topic. Topic : single phase half controlled rectifie...

A: Single-phase half controlled rectifier fed DC series motor:- Single-phase controlled Rectifier Contr...

Q: Use the node-voltage method to find v¡ in the circuit shown. 4.6 6 is 2Ω 3Ω + 60 V V1 { 24 N 3 0 Ans...

A: The given circuit is:

Q: How can I find the solutions for this problem? (answers are given) Answers: a.i. Eth = 4 V, Rth = 3....

A: Click to see the answer

Q: Find the time functions corresponding to each of the following Laplace transforms using partial frac...

A: Click to see the answer

Q: Application of load flow analysis in power system planning in detail

A: Load flow study is considered to be one of the most important and detailed study of the power system...

Q: A PMMC instrument has FSD of 100 µA and a coil resistance of 1 kſN. Calculate the re- quired shunt r...

A: Given values are - ImFSD=100μARm=1000OhmI=100mA

Q: what is the value of resistor R if it is known that ix = 0.5 A?

A: For this problem, we have to use KVL analysis

Q: what is veal of R?

A: Click to see the answer

Q: Assume you have a plant defined by the transfer function G(s)= sta Let Y(s) = G(s)U(s) where U(s) is...

A: To find the output y(t) in time domain for different inputs

Q: An ammeter has a PMMC instrument with a coil resistance of R = 99 N and FSD current of 0.1 mA. Shunt...

A: Given values are - Im=0.1mARm=99OhmRSh=1Ohm

Q: In the circuit given below, R = 4 Ω. Calculate v1 and v2.    The value of v1 in the circuit is _____...

A: Click to see the answer

Q: I just need help with part c.

A: Applying KCL in the following circuit for t>0 Let v is the voltage across all elements in parall...

Q: Transmission and Distribution of Electric Power Answer the Following Question Please: Q) Three-phase...

A: Click to see the answer

Q: In the circuit given below, R = 18 Ω. Find the value of v0 using nodal analysis.  The nodal equation...

A: Given R = 18 Ω To write the nodal equation  The nodal equations are: v1/ A + (v1 − 60)/B + C/20 = 0 ...

Q: Can you find equivalent resistance?

A: The given circuit can be modified as

Q: 1. For a JFET self-bias circuit with VDD = 18 V, RG = 1 MQ, RD = 1.5 kN, Rs = 750 N, IDSS = 10 mA an...

A:  Since you have asked multiple question so we will solve the first question for you. If you want any...

Q: Give output function, transition table and State diagram by analyzing the Sequential circuit shown i...

A: The given circuit is designed using SR flip-flop. First draw the state table for SR flip-flop: S ...

Q: There are conductor x (number of conductors = 3) and conductor y (number ofconductors = 2’) for a 50...

A: a) Calculating Ds1 Ds1=rx'd12.d133Ds1=0.7788rxd12.d133Ds1=0.7788×0.030.5.0.5+1.53Ds1=0.2859 m Calcul...

Q: A 1-H inductor is connected in series with a 6-ohm resistor. If the connection is energized from a 9...

A: As  current through long time indicates that time "t" tends to infinity

Q: What is the largest time delay that can be achieved using Timer0 and a pre-scaler? Assuming the micr...

A: Given: Timer 0 and a Prescaler is used to provide time delay. The microcontroller uses an external c...

Q: Explain why voltage spikes and surges are high-frequency occurrences.

A: Voltage spikes and surges in a circuit occur when there is a sudden release of energy stored in vari...

Q: All resistors (R) in the given figure are 15 Ω each. Find Req. The value of Req is _______ Ω.

A: Given all resistors are R=15 ohm

Q: In the circuit given below, R = 45 Ω. Find the currents I1 through I4 and the voltage v0.      The v...

A: Click to see the answer

Q: S:40)

A: Click to see the answer

Q: Please give the solution of this question.

A: To apply KVL we have to modify the given circuit as  The KVL equation is given as 

Q: What do you understand by Safety factor, puncture and Flashover of Insulator?

A: The safety factor is, Safety factor=Puncture voltageFlash over voltageFor example safety factor of p...

Q: Given that sampling frequency (fs) is equal to 250Hz and Nyquistfrequency (fN) is equal to two times...

A: According to question: fS=250Hz∵fN=fS2⇒fN=2502⇒fN=125Hz∵fN=2fA⇒fA=fN2⇒fA=1252⇒fA=62.5Hz

Q: Using KVL, find the voltage across R3 for the circuit shown in Figure 1.

A: In mesh analysis, if the dominating mesh current is entering the voltage source then the voltage dro...

Q: Sketch vo for the given network and determine the dc voltage available

A: Click to see the answer

Q: Source Transformation

A: Given two circuits which are equivalent to each other due to a source transformation  Source transfo...

Q: it is usually composed of large capacity circuit breaker  that serves as a bridge between the source...

A: The switchgear is only element that connected between supply and load to controlling , regulating an...

Q: Q-1 Find the orthogonal trajectories of y ae" where a be the arbitrary constant,

A: Click to see the answer

Q: Find the vab Voltage when the given Circuit 1 is connected to the Circuit 2 through their a and b te...

A: consider first

Q: Find the value of C (in uF in the network in the figure below such that the total load has a power f...

A: According to question: Load rating in MW is calculated as PL=SL×pf⇒PL=20×0.707⇒PL=14.14MW Now power ...

Q: Requires if possible 1.Detailed circuit diagram of 8 bit DAC& Process explanations 2.Calculation...

A: What is a Digital-to-Analog Converter? A Digital to Analog Converter commonly referred as DAC, D/A o...

Q: In the circuit given below, R = 8 Ω. Find the current i.  The value of i in the circuit is ______ A.

A: Click to see the answer