The total manometric height of the pumped solar water heating system with a surface area of 100 m² in Çanakkale is 20 meters. The collectors are located in the south direction and at latitude angle. Determine the angle of incidence of beam radiation on he collectors at 14:00 on July 10. Since water circulates in the system at a flow rate of 80 liters/m²h, determine the pump power, main pipe diameter and water velocity in the main pipe.

The total manometric height of the pumped solar water heating system with a surface area of 100 m² in Çanakkale is 20 meters. The collectors are located in the south direction and at latitude angle. Determine the angle of incidence of beam radiation on he collectors at 14:00 on July 10. Since water circulates in the system at a flow rate of 80 liters/m²h, determine the pump power, main pipe diameter and water velocity in the main pipe.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.37P

See similar textbooks

Similar questions

A rectangular duct made of commercial steel is used to channel air at 1 atm and 35°C at an average velocity of 7 m/s. The duct is 15 cm by 20 cm and 12 m long. Disregarding the entrance effects, determine the fan power needed to overcome the pressure losses in this section of the duct.
The liquid storage tank shown in Fig has two inlet streams with mass flow rates w1 and w2 and an exit stream withflow rate w3. The cylindrical tank is 2.5 m tall and 2 m in diam-eter. The liquid has a density of 800 kg/m. Normal operating procedure is to fill the tank until the liquid level reaches a nom-inal value of 1.75 m using constant flow rates:w1=120 kg/min, w2=100 kg/min, and w3=200 kg/min. At that point, inlet low rate w1 is adjusted so that the level remains constant.However, on this particular day, corrosion of the tank has opened up a hole in the wall at a height of 1 m, producing a leak whose volumetric flow rate q4(m3/min) can be approximated by q4=0.025√h−1 where h is height in meters.(a)If the tank was initially empty, how long did it take for theliquid level to reach the corrosion point?(b)If mass flow rates w1,w2,and w3 are kept constant indefi-nitely, will the tank eventually overflow? Justify your answer.
Water at 15°C is to be heated to 65°C by passing it over a bank of resistance heating rods 4 m long and 1 cm in diameter which are maintained at 90°C. The water is approached by the heater rod bank at the normal direction at an average speed of 0.8 m/s. The rods are arranged in line with longitudinal and transverse steps of SL = 4 cm and ST = 3 cm.Determine the number of rows of NL tubes in the direction of flow needed to achieve the indicated temperature rise. I need the solution from fundamental concepts of how the heat flow behaves in the system
The minimum fresh air requirement of a residential building is specified to be 0.35 air changes per hour (ASHRAE, Standard 62, 1989). That is, 35 percent of the entire air contained in a residence should be replaced by fresh outdoor air every hour. If the ventilation requirement of a 2.7-m-high, 200-m2 residence is to be met entirely by a fan, determine the flow capacity in L/min of the fan that needs to be installed. Also determine the minimum diameter of the duct if the average air velocity is not to exceed 5 m/s.
Two water reservoirs A and B are connected to each other through a 40-m-long, 2-cm-diameter cast iron pipe with a sharp-edged entrance. The pipe also involves a swing check valve and a fully open gate valve. The water level in both reservoirs is the same, but reservoir A is pressurized by compressed air while reservoir B is open to the atmosphere at 95 kPa. If the initial flow rate through the pipe is 1.5 L/s, determine the absolute air pressure on top of reservoir A. Take the water temperature to be 10°C.
During a retrofitting project of a fluid flow system to reduce the pumping power, it is proposed to install vanes into the miter elbows or to replace the sharp turns in 90° miter elbows by smooth curved bends. Which approach will result in a greater reduction in pumping power requirements?
Determine the Height of a chimney with a static draft of 12 mm if the losses total draft is 4 mm, the ambient air temperature is 35 ° C and theexhaust gas temperature is 450 ° C. The fuel consumption of the boiler is 600 kg / h, the mass of the exhaust gas is 16 kg, also determine the air mass ma, the diameter of the chimney and the velocity of the exhaust gases.
Need help with the following questionA reducing elbow in a horizontal pipe is used to deflect water by an angle of110° from the flow direction while accelerating it. Hot water at 80°C flowsat a rate of 33 kg/s in the pipe. The elbow discharges water into theatmosphere. The cross-sectional area of the elbow is 150 cm2at the inlet and25 cm2at the outlet. The elevation difference between the entrance and theexit of the pipe is 40cm. The total mass of the elbow and water in it is 50kg.Take the momentum-flux correction factor to be 1.03 at both inlet and outlet.Determine : -The inlet and outlet water velocities. -The gage pressure at the center of the inlet of the elbow. -The anchoring force required to hold the elbow in place.
What are the applications and principles of Laser-Doppler Anemometer to agricultural and biosystems engineering?
Electric power is to be generated by installing a hydraulic turbine—generator at a site 120 m below the free surface of a large water reservoir that can supply water steadily at a rate of 930 kg/s. If the mechanical power output of the turbine is 850 kW and the electric power generation is 770 kW, determine the turbine efficiency and the combined turbine— generator efficiency of this plant. Neglect losses in the pipes.
For these velocity distributions in a round pipe, indicate whether the kinetic-energy correction factor ∝ is greater than, equal to, or less than unity.
What is the operating principle of variable-area flowmeters (rotameters)? How do they compare to other types of flowmeters with respect to cost, head loss, and reliability?