The truss shown is hinged at A and F. Find the reaction/s at the support and force in each members of the truss and determine whether they are in tension or compression. Make a summary and draw a FINAL FBD. Note: Round off EVERY computation and answer up to FOUR (4) decimal places. P1= 15 kN, P2= 2 4,9kN and P3= 15.9g kN Members Tension/ Compression Forces P1 P2 P3 CB - 1.45 m--1.75m- 2. 4 pm СЕ CH A CG GF 1.)D m GH 3.89 m АВ H. 5. 49m EF E EA G. ВЕ DC DH

The truss shown is hinged at A and F. Find the reaction/s at the support and force in each members of the truss and determine whether they are in tension or compression. Make a summary and draw a FINAL FBD. Note: Round off EVERY computation and answer up to FOUR (4) decimal places. P1= 15 kN, P2= 2 4,9kN and P3= 15.9g kN Members Tension/ Compression Forces P1 P2 P3 CB - 1.45 m--1.75m- 2. 4 pm СЕ CH A CG GF 1.)D m GH 3.89 m АВ H. 5. 49m EF E EA G. ВЕ DC DH

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Set P1 = 30 kN and P2 = 16 kN in Part A Determine the force in member AD, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. View Available Hint(s) FAD= SubmitPrevious Answers Incorrect; Try Again; 4 attempts remaining Part B Determine the force in member BC, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. View Available Hint(s) FBC = SubmitPrevious Answers Incorrect; Try Again; 5 attempts remaining Part C Determine the force in member BD, and state if the member is in tension or compression. Express your answer to three…
DETERMINE THE INTERNAL FORCE OF MEMBER EF FROM THE FIGURE BELOW. Use four (4) decimal places during computation and two (2) decimal places for the final answer. Note: for compression, include a negative sign ( - ) and for tension, type answer as is.
Determine the largest force P (kN), directed as shown in the figure that can be applied to the bracket if the allowable normal stresses on section A-B are 8 Mpa in tension and12 Mpa in compression. A119.15 B.79.44 C.18.64 d.14.31 answer:14.31
Set P1 = 70 kN, P2 = 50 kN Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. a) Determine the force in member BG of the truss. b) Determine the force in member CD of the truss. c) Determine the force in member CF of the truss.
Set P1 = 70 kN, P2 = 50 kN. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. a) Determine the force in member CG of the truss. b) Determine the force in member DE of the truss. c) Determine the force in member DF of the truss. d) Determine the force in member EF of the truss. e) Determine the force in member FG of the truss.
Calculate the required amount of reinforcement (in in2) considering the ultimate moment below. Use english units. Note: Use the following equations for minimum reinforcement in English units. Pmin for flexure = (3*sqrt (f'c))/fy greater than or equal to 200/fy f'c = 3000 psi fy = 40 ksi Mult = 200 ft-k
If P= 8.571 kN, Determine the stress in member CEassuming that the area in steel is 24 mm2.Show FBD
In the overhanging beam show, determine P so that the moment over each support equals the moment at the midspan. W= 3.7 kN/m. Round your answer to 2 decimal places.
The force F in the figure is equal to 10 kN. Determine the following forces: 1. Forces at support BD in kN 2.tension on cable CE in kN 3.Force at support A in kN.
Determine the magnitude of the 15 points force in member CD using method of section * (O 35.3KN Tension O none of the above (O 15.02KN Tension () 27.7 KN Compression (O 13.83 KN Tension O 16.2 KN Compression
The wooden members in the simple truss below have the following capacity: Shear parallel to grain = 1 MPa, Compression parallel to Grain = 11MPa, Compression perpendicular to Grain = 5 MPa 1. Find the minimum safe x. a. 73 mm b. 160 mm c. 148 mm d. 112 mm 2. Find the minimum safe y. a. 15.97 mm b. 19.45 mm c. 9.14 mm d. 18.28 mm 3. Determine the stress in member AC. a. 1.13 MPa b. 1.258 MPa c. 1.224 MPa d. 1.04 MPa
Set P1 = 6.8 kN , P2 = 8 kN . Determine the force in the member AB, and state if the member is in tension or compression. Determine the force in the member AE, and state if the member is in tension or compression. Determine the force in the member DEDE, and state if the member is in tension or compression.