The uniform 14-kg plate is welded to the vertical shaft, which is supported by bearings A and B. Calculate the magnitude of the force supported by bearing B during application of the 115-N-m couple to the shaft. The cable from C to D prevents the plate and shaft fro turning and the weight of the assembly is carried entirely by bearing A. 115 N.m A 250 mm

The uniform 14-kg plate is welded to the vertical shaft, which is supported by bearings A and B. Calculate the magnitude of the force supported by bearing B during application of the 115-N-m couple to the shaft. The cable from C to D prevents the plate and shaft fro turning and the weight of the assembly is carried entirely by bearing A. 115 N.m A 250 mm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.19P: The 3600-lb car with rear Wheel drive is attempting to tow the 4500-lb crate. The center of gravity...

See similar textbooks

Similar questions

The spring attached to the homogenous bar of weight W is undeformed when =0. Determine the smallest spring stiffness k for which the =0 equilibrium position will be stable. Use W = 10 lb, a = 24 in., and b = 6 in. Assume that the spring remains horizontal, which is a valid approximation if is small.
The homogeneous plate of weight W is supported by a ball-and-socket joint at D and three wires. Draw the FBD of the plate and count the unknowns.
The 5.33-kg cylinder is suspended from two equal-length cords (L = 690 mm). The end of each cord is attached to a ring (negligible mass) as shown in the figure. The ring passes along a horizontal shaft. Provided that the rings can be separated by the greatest distance d = 352 mm and still support the cylinder, determine the coefficient of static friction between each ring and the shaft. The only answer is 0.264. Thanks.
The homogenous bar A having a mass of 18 kg is 2 m long and is inclined at 60 degrees with the horizontal plane. The mass M of 7 kg is connected by the rope to the bar. The rope leaving the bar is horizontal. The coefficient of friction between the rope and the drum B is 0.20. What is the minimum coefficient of friction between the bar and the plane for equilibrium? Give solution. (Ans. coefficient of friction = 0.284)
A 60-kg cabinet is mounted on casters that can be locked to prevent their rotation. The coefficient of static friction between the floor and each caster is 0.35. 3. If h = 600 mm, determine the magnitude of the force P (in N) required to move the cabinet to the right if the casters at A are locked and the casters at B are free to rotate. (ANSWER: 72.5)
The homogenous 360 kg block rests against the vertical wall, for which the coefficiewnt of friction is 0.25. A force P is applied to the midpoint of the right face in the direction shown in thre figure. What range of values may P have without disturbing equilibrium. Give solution. (Ans. 5260 N < P < 7890 N)
A 120-lb cabinet is mounted on casters that can be locked to prevent their rotation. The coefficient of static friction between the floor and each caster is 0.30. If h = 32 in., determine the magnitude of the force P required to move the cabinet to the right (a) if all casters are locked, (b ) if the casters at B are locked and the casters at A are free to rotate, (c) if the casters at A are locked and the casters at B are free to rotate.
A 150-lb block rests on a horizontal floor. The coefficient of friction between the block and the floor is 0.30. A pull of 40 lb, acting upward at an angle of 30° to the horizontal, is applied to the block. Determine whether or not the block will slide. - Draw Free-body diagram - Solve most simple way - use the formula Fmax= Ms (N)
PROBLEM 1: The 1500-kg beam ABC has fixed support at A and connected to beam BD by hinge at B. Beam BD has a mass of 2000 kg and supported by a cable at D. The cable is attached to the 20-cm-diameter pulley at E and pulled vertically at the other end, by tension T. Given: a = 1.5 m; b = 0.9 m; c = 1.8 m d = 0.6 m; e = 1.4 m; θ = 75°. Calculate the required tension to maintain in equilibrium. (ANSWER: 12.830KN) Calculate the moment reaction at A. (ANSWER: 28.499) Calculate the total reaction at A. (ANSWER: 22.192) Calculate the vertical reaction at E. (ANSWER: 25.223)
The torsional spring at B is undeformed when bars OB and BD are both in the vertical position and overlap. If a force F is required to position the bars at a steady orientation θ = 64°, determine the torsional spring stiffness kT. The slot at C is smooth, and the weight of the bars is negligible. In this configuration, the pin at C is positioned at the midpoint of the slotted bar.
Determine the weight of block B for the 250N block A not to slidedown in the inclined plane. Given that the coefficient of staticfriction in the 45° inclined plane is 0.25 and in the 30° inclinedplane is 0.3. (Assume frictionless pulley) Answer: WB = _____________
A 60-kg cabinet is mounted on casters that can be locked to prevent their rotation. The coefficient of static friction between the floor and each caster is 0.35. 1. If h = 600 mm, determine the magnitude of the force P (in N) required to move the cabinet to theright, if all the casters are locked. (ANSWER: 206) 2. If h = 600 mm, determine the magnitude of the force P (in N) required to move the cabinet to the right if the casters at B are locked and the casters at A are free to rotate. (ANSWER: 178)