The volume of the solution that can be measured with 5-10 microliter pipette and 2-20 microliter pipette is 0.005-0.01 mL and 0.002 mL-0.02 mL. The volume of the solution that can be measured with 20-200 microliter is 0.02-0.2 mL. The volume 1 mL of solution is measured with 100-100 microliter which has capacity of 0.1 mL to 1 mL. What would the display read for 0.10 mL, 0.20mL, 0.40mL, 0.60 mL, 1.0 mL read when using the micropipettes mentioned above

The volume of the solution that can be measured with 5-10 microliter pipette and 2-20 microliter pipette is 0.005-0.01 mL and 0.002 mL-0.02 mL. The volume of the solution that can be measured with 20-200 microliter is 0.02-0.2 mL. The volume 1 mL of solution is measured with 100-100 microliter which has capacity of 0.1 mL to 1 mL. What would the display read for 0.10 mL, 0.20mL, 0.40mL, 0.60 mL, 1.0 mL read when using the micropipettes mentioned above

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter33: Automated Methods Of Analysis

Section: Chapter Questions

Problem 33.8QAP

See similar textbooks

Similar questions

Standardization of Sodium Thiosulfate Solution Primary Standard used: Potassium Dichromate Formula mass of 1o standard: __________________ % Purity of 1o standard: 99.80% Trials 1 2 3 Weight of K2Cr2O7 (g)Weight of K2Cr2O7 (g) 0.0315 0.0331 0.0380 Final Volume Reading Na2S2O3 (ml) 27.50 27.50 34.90 Initial Volume Reading Na2S2O3 (ml) 1.10 0.00 1.00 Net Volume Na2S2O3 used (ml) Molarity of Na2S2O3
(6.65x10^5)/(6.60x10^-6) (3.73x10^8) Please Calaculition. Only typed solution
SALT SOLUTION: Trial 1: Volume: 25 mLMass of 25mL solution: 29.824 gDensity: 1.2 g/mL Trial 2:Volume: 25 mLMass of 25 mL solution: 29.855 gDensity: 1.2 g/mL Trial 3:Volume: 25 mLMass of 25 mL solution: 29.816 gDensity: 1.2 g/mL METAL BAR: Method I - Trial 1:Mass of metal bar: 57.063 gVolume of metal bar: 6.7 cm^3Density of bar: 8.5 g/cm^3 Trial 2:Mass of metal bar: 57.063 gVolume of metal bar: 6.0 cm^3Density of bar: 9.5 g/cm^3 Trial 3:Mass of metal bar: 57.063 gVolume of metal bar: 6.0 cm^3Density of bar: 9.5 g/cm^3 Method 2 - Trial 1:Dimensions: diameter = 1.20 cm, height = 4.91 cmMass of metal bar: 57.063 gVolume of metal bar: 5.55 cm^3Density of bar: 10.3 g/cm^3 Trial 2:Dimensions: diameter = 1.20 cm, height = 4.95 cmMass of metal bar: 57.063 gVolume of metal bar: 5.60 cm^3Density of bar: 10.2 g/cm^3 Trial 3:Dimensions: diameter = 1.20 cm, height = 4.95 cmMass of metal bar: 57.063 gVolume of metal bar: 5.60 cm^3Density of bar: 10.2 g/cm^3 QUESTION - From your data, calculate the…
A standard solution mixture containing each element at 500 ppm is provided. You will need to carefully dilute this so that your total volume is up to 50ml per standard solution mixture in the digitubes. Prepare calculations to show how you are going to prepare your calibration standards.
Volumetric pipettes are designed to deliver a precise amount of liquid, but only if you a. submerge the end of the pipette into a solution you are delivering. b. allow the pipette to drain freely, and leave any residual solution in the pipette. c. hold the pipette at a 45 degree angle and ensure that all the liquid is delivered.
Calculate the Constant Weight (in grams) of the Empty Crucibles. Show your solution. Crucible No. 1 2 3 Weighing 1 22.6035 22.0223 24.1535 Weighing 2 22.6017 22.0204 24.1533 Weighing 3 22.5994 22.0199 - Weighing 4 22.5992 - - Constant Weight, g ??? ??? ???
0.2 to 1.0 mg/ml: For each concentration, a volume of 1.0 mL should be prepared. How will you prepare these standards using micropipettes and which one would you use? There is a: 0,5-10 microliter pipette; 2-20 microliter pipette 20-200 microliter pipette 100-1000 microliter pipette.
1000 mL of 0.45% NaCl IV for 6.5 hoursDrop factor: 60 gtt/mL Flow rate: ________ gtt/min
4. A fat sample with combination of acids contain standard hydrochloric acid for blank and sample with 8mL and 5mL respectively. The normality of the standard hydrochloric acid is 0.93N and the weight of the sample is 3 grams. Calculate the saponification value.
What weight of mercury bichloride should be taken as sample, assuming 100% purity, so that 0.5 g og HgS will be obtained in a gravimetric analysis? Gravimetric factor = 1.1669
Before Investigating the scene the technician must dilute the luminol solution to a concentration a 2.00 × 10-2 M. The diluted solution is then placed in a spray bottle for application on the desired surfaces. How many moles of luminol are present in 2.00L of the diluted spray?
The density of the first fraction collected would be expected to be close to a value of ______. 1.00 g./mL 0.895 g/mL 0.789 mL 0.950 g.mL