The wind velocity on the upstream side of a wind turbine is 4 m/s. If the turbine extracts 26% of the available kinetic energy, what is the wind velocity on the downstream side of the turbine in m/s? Please include one decimal place in your answer.

The wind velocity on the upstream side of a wind turbine is 4 m/s. If the turbine extracts 26% of the available kinetic energy, what is the wind velocity on the downstream side of the turbine in m/s? Please include one decimal place in your answer.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter2: Matter And Energy

Section: Chapter Questions

Problem 29RQ: If 3000 ft3 of air is crossing an evaporator coil and iscooled from 75F to 55F, what would be the...

See similar textbooks

Related questions

Q: A beam is subjected to a linearly distributed downward load and rests on two wide supports BC and DE…

Q: Your boss is convinced and decided that the customers will save a lot of energy in processing…

A: This question is based on scientific opinion.

Q: Car A, with A-1600 kg, is stopped at a red light. Car B, with m8-2100 kg and a speed of v = 42 km/h.…

A: “Since you have posted a question with multiple sub parts, we willprovide the solution only to the…

Q: 20.The following performance of gas turbine engine: compressor inlet temperature, 525°R;…

A: Given Data - Turbine Inlet temperature T1=1505'R Turbine isentropic discharge temperature =1185°R…

Q: A load P is supported by a structure consisting of rigid bar BDF and three identical 15-mm- diameter…

A: Given: A load P is supported by a structure consisting of rigid bar BDF and three identical (d)…

Q: A mass m is suspended by three cables attached at three points B, C, and D, as shown in Figure 1.…

Q: Determine the water flow in the pipe in relation to the diameter of the outlet pipe, if the…

Q: QUESTION 3 For the stress element below, when a = 6, b = 6, and c = 3, the maximum shear stress T,…

Q: 2.2 An oven whose thickness of side wall is 82.5mm has a thermal conductivity of wall insulation of…

A: (2.2) To find: The area of the wall surface. Given: The thickness of the side wall is L=82.5 mm1…

Q: A copper cylinder (c=390 J/kg K) with a mass of 75 g is placed in a furnace at a temperature of 312…

A: A copper cylinder Ccu=390 J/kg K = 0.390 J/g K Mass of cylinder mcu= 75 g Temperature of furnace…

Q: The global stresses in a three-ply laminate are given at the top and bottom surface of each ply in…

A: Solution: Given Data: t=0.005 inA=4 in × 4 in To Find: (a) Resultant force component Nx for the…

Q: Knowing that a force P of magnitude 42 kN is required to punch a hole of diameter d'= 20 mm in an…

A: Given data force = 42 kN Diameter= 20mm Thickness = 5 mm Find the average shear stress

Q: Air enters into a nozzle at 4 bar and leaves at 1 bar, 350 °C and 700 m/s. Determine temperature of…

Q: AW-16-lb weight block is lifted vertically by a force of F-27 lb. Determine its acceleration. (Hint:…

Q: 6. Both jigs and fixtures hold, support, and also guides the cutting tool. 7. Support surface…

A: This question is based on the concept of jigs and fixture.

Q: An aluminium tube carrying a hot liquid at 118°C has 12 integrally machined longitudinal fins on its…

Q: Consider the forces shown in Figure 1). ▾ Part A Determine the moment of each of the three forces…

A: According to the given data F1=250N F2=300N F3=500N We need to find Moment of the forces about A

Q: Figure 9-42 Full Alternative Text 9-43. Determine the principal stresses in the box beam at point B.…

A: Draw the free-body diagram of the beam.

Q: Q3. A circular, steel, rotating shaft is subjected to a bending moment of M Nm* and direct tensile…

Q: 4. The change in weight of an airplane is determined from reading the strain gauge A mounted in the…

A: Since you have posted multiple questions, we will provide the solution only to the first question as…

Q: 3. How to locate a short cylindrical component? Please use a drawing for the illustration and point…

A: To find: How to locate a short cylindrical component.

Q: Solving fluid dynamic problem, flow through a cylinder, a uniform gradient only applied in z…

A: Given Data: low through a cylinder, a uniform gradient only applied in z direction, If r is the…

Q: The beam seciton shown below has moment of inertia about its neutral axis: I = 301.3 (106) m 4, and…

Q: A grandmother is concerned about reducing her winter heating bills. Her strategy is to loosely fit…

A: (a) Draw the diagram of window and its insulation of foam sheet when foam is placed on the inner…

Q: Using the table below, estimate the components of the matrices and develop the stiffness and…

A: Solution: Given Data: Material is E-glass/470-36 E-glass/vinylester To Find: (a) The stiffness…

Q: (3.b) A converging-diverging nozzle is designed to expand air from a chamber in which the pressure…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: Consider a steam power plant operating on the ideal Rankine cycle with reheat between the pressure…

A: To Find : The reheat pressure of the cycle for the case (A) single (B) Double Given : The pressure…

Q: Consider the feedback system in the following figure. Compute the transfer function Y(s) Ta(s) and…

A: Solution: Given Data: To Find: (a) Transfer function YsTd(s) (b) Transfer function Y(s)Ns

Q: Determine the moment of inertia of the area about: a) the x-axis b) the y-axis a=135mm b=75mm 75 mm

A: Given: a = 135 mm b= 75 mm The radius of the circle,r = 75mm To find: Ix and Iy

Q: Odd side please

Q: 4.25 An automobile, having a mass of 1000 kg, runs over a road bump of the shape shown in Fig. 4.49.…

A: Given, The mass of the automobile, m = 1000 kg The speed of the automobile, v = 50 km/h = 13.88 m/s…

Q: The shaft, described in the previous question, is considered here again. Consider that the maximum…

A: Maximum stress = 490 MPa Minimum stress = -95 MPa Find the mean, stress amplitude and summation of…

Q: Determine the moment produced by force Fc about point O (Figure 1). Express the result as a…

Q: 14. A certain gas in a Tank has internal energy of 112 kJ and enthalpy of 145.6 kJ at 2 atm. The…

A: According to the given data H=145.6 kJ U=112 kJ P=2atm=200kpa We need to find The volume of the…

Q: 1. At what flow angle will the flow become just sonic downstream of the nozzles of a high pressure…

A: Given: The shroud diameter ds=250 mm=0.25 m The hub to shroud diameter ratio r=0.8 The stagnation…

Q: Calculate the reaction at the pinned wall joint and the tension in the cable for the system shown.…

Q: ball is dropped from a height of 10 m on a fixed steel platform. Determine the height to which the…

A: This question is based on the concept of the mechanics

Q: 4. A 90° elbow in a horizontal pipe is used to direct water flow upward at a rate of 40 kg/s. The…

A: Water flow rate = 40 kg/s Diameter of pipe = 10cm Elevation difference = 50 cm Assumptions The flow…

Q: 2.1 A plane wall with thermal conductivity of 10.2 W/m °C, thickness of 100mm, and area of 3m². The…

A: According to Bartleby guideline, we can solve only one question at a time. Please post other…

Q: (3.b) A converging-diverging nozzle is designed to expand air from a chamber in which the pressure…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: What is the difference between laminar and turbulent flow, and how does this affect fluid mechanics…

A: In fluid mechanics, laminar and turbulent flow are two types of fluid flow that have different…

Q: Determine the moment of inertia and the radius of gyration of the shaded area with respect to the…

Q: Compute the reduced stiffness [Q] matrix for a lamina with E1 = 35 GPa, E2 = 3.5 GPa, V12 = 0.3, G12…

A: The value of lamina are E1=35 GPa, E2=3.5 GPa, ν12=0.3,G12=1.75 GPa, G23=0.35 GPa

Q: The beam is subjected to an internal moment of M=122 kN-m- (Figure 1) Figure 30 mm, M C 150 mm 150…

A: Part (A): Draw the diagram of cross-section of inverted T section.

Q: The height of the manometer depends on the _______ of the manometric fluid. 2. _______ gives the…

A: To find: The word for the blank.

Q: A2.35 m diameter wheel shown below rolls to the right with an angular speed of 21.288 rad/s.…

Q: 1 - Consider 2 kg of water in a cylinder blocked by a piston at 20 C, 200 kPa. Water is heated and…

A: The mass of water is m=2 kg. The initial pressure on the piston is P1=200 kPa. The initial…

Q: A local farm uses a tractor as a prime-mover for carrying out farm operations such as: plowing,…

A: Draw the given diagram.

Q: The gas entering a rocket nozzle has a stagnation pressure of 1500 kPa and a stagnation temperature…

A: Given: 5

Q: A dumbbell is suspended by two cables, where 0 = 46° and T ||T|| Determine the approximate weight of…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

If 3000 ft3 of air is crossing an evaporator coil and iscooled from 75F to 55F, what would be the volume of air, in ft3, exiting the evaporator coil?
5 The wind velocity on the upstream side of a wind turbine is 2.2 m/s. If the turbine extracts 28% of the available kinetic energy, what is the wind velocity on the downstream side of the turbine in m/s? Please include one decimal place in your answer.
If you rent a car, you can (1) return it with a full gas tank, (2) return it without filling it and pay $5.75/gallon, or (3) accept a fixed price of $60 for gas. The local price is $3.50/gallon for gasoline, and you expect this car to get 25 miles per gallon. The car has a 16-gallon tank. What choice should you make if you expect to drive: (a) 150 miles? (b) 300 miles? (c) 450 miles? (d) How do your answers change if stopping at the filling station takes 20 minutes and your time is worth $15/hr?
Why did you multiply 249.57 gal/s by the density of water, 8.34 lb/gal? 249.57 gal/s is the flow rate of air, NOT water.
The fuel consumption of an automobile is 14 km/ L.The fuel consumption, in miles per gallon, is?
Consider the flow of air through a wind turbine whose blades sweep an area of diameter D (in m). The average air velocity through the swept area is V (in m/s). On the bases of the units of the quantities involved, show that the mass flow rate of air (in kg/s) through the swept area is proportional to air density, the wind velocity, and the square of the diameter of the swept area
Given the lifting table shown below, The diameter of the plunger DP 20 cm. The ram diameter DR 60 cm , The efficiency is 100 %, The stroke of the plunger is 30 cm. The ram has to raise a load F2 = 20 kN. Find: a) The force F1 exerted on the plunger b) the number of strokes needed to raise the load given above by a distance of 10 cm . c) the volume of oil pumped if the load moves by 30 cm (using plunger force given in a ) d) What will be the new diameter of the ram piston if the new load force is 16 times the force exerted in the plunger the diameter of the plunger is kept to 20cm. (please check the picture carefully).
29 - Water is drawn from the bottom of a large tank filled with water open to the atmosphere. If the outlet velocity is 7.2 m/s, what could be the height of the water in the tank? a) 2.64m B) 4.38m NS) 3.65 m D) 5.46 m TO) 2.20m 30 - What would be the weight of an object with a mass of 100 kg in a place where the gravitational acceleration is 8 m/s²? a) 42.2 kgf B) 98.1 N NS) 800 N D) 9810 N TO) 196.2 N
Start with 1 lbf ft ⁄s and convert it to N⋅m/s and show that 1 lbf ⋅ ft ⁄s is equal to 1.36 W. Knowing that 550 lbf ⋅ ft ⁄s is equal to 1 hp (horsepower), how many kW is that?
To apply the principle of work and energy to a system of particles. The principle of work and energy can be extended from one particle to include a system of particles as follows: ∑T1+∑U1−2=∑T2 where ∑T1 is the system's initial kinetic energy, ∑U1−2 is the sum of the work done by all external and internal forces acting on the system's particles, and ∑T2 is the system's final kinetic energy. When the particles either are undergoing only translational motion or are connected by inextensible cables, the internal forces of the particles negate each other; only the external forces are required in the principle of work and energy. When frictional forces are present, the work done by the frictional force is UF=μkNs, where μk is the coefficient of kinetic friction, N is the normal force, and s is the body's displacement. In this equation, the work done by friction represents both the external work of friction and the internal work that is converted into various forms of internal energy, such…
To apply the principle of work and energy to a system of particles. The principle of work and energy can be extended from one particle to include a system of particles as follows: ∑T1+∑U1−2=∑T2 where ∑T1 is the system's initial kinetic energy, ∑U1−2 is the sum of the work done by all external and internal forces acting on the system's particles, and ∑T2 is the system's final kinetic energy. When the particles either are undergoing only translational motion or are connected by inextensible cables, the internal forces of the particles negate each other; only the external forces are required in the principle of work and energy. When frictional forces are present, the work done by the frictional force is UF=μkNs, where μk is the coefficient of kinetic friction, N is the normal force, and sis the body's displacement. In this equation, the work done by friction represents both theexternal work of friction and the internal work that is converted into various forms of internal energy, such as…
Given the lifting table shown below , The diameter of the plunger DP 8 cm.The ram diameter DR 48 cm , The efficiency is 100 %, The stroke of the plunger is 18 cm. The ram has to raise a load F2 = 2 kN. Find : a) the force F1 exerted on the plunger b) the number of strokes needed to raise the load given above by a distance of 10 cm c) the volume of oil pumped if the load moves by 20 cm ( using plunger force in a ) d) What will be the new diameter of the ram piston if the new load force is 16 times the force exerted in the plunger the diameter of the plunger is kept to 8cm .