This engine is used in a hoist. Motor 2.5 kW with the help of gears with a power of and n = 500 rpm. transmits. If the shear strength of the AB shaft is τa = 160 MPa; a) Find the diameter of AB shaft with 1.4 times safety. b) Find the maximum force F the engine can carry.

This engine is used in a hoist. Motor 2.5 kW with the help of gears with a power of and n = 500 rpm. transmits. If the shear strength of the AB shaft is τa = 160 MPa; a) Find the diameter of AB shaft with 1.4 times safety. b) Find the maximum force F the engine can carry.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.4.5P: A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions...

See similar textbooks

Related questions

Q: A hollow steel shaft transmits 600 kW at 500 r.p.m. The maximum shear stress is 62.4 MPa. Find the…

A: Find the outside and inside diameter .

Q: Find the maximum stress developed in a stepped shaft when it is subjected to a: i) Torque of “T” Nm.…

Q: A shaft is required to transmit 285 kW power at 255 r.p.m. The maximum torque may be 1.8 times the…

A: Given that , Power P=285KW=285×106N-mm/sShear stress σs=46Mpa=46N/mm2Angle of twist…

Q: A solid steel shaft must not twist through more than 30 in a 6-m length when ted to a torque of 12…

A: Given Twist angle = 30 Length = 6m Torque = 12 kNm Modulus of rigidity = 83 GPa To find Smallest…

Q: (8) A steel shaft transmits 30kW @ 1,400rpm. Considering allowable shearing stress based on pure…

A: According to guidelines first question will be done from multiple questions. Please post again for…

Q: 8) A steel shaft transmits 30kW @ 1,400rpm. Considering allowable shearing stress based on pure…

A: Given:P=30 kWN=1400 rpmζ=35 MPaG=83 GPa

Q: A solid steel shaft must not twist through more than 30 in a 6-m length when subjected to a torque…

Q: A hollow shaft is to transmit 300 kW at 80 r.p.m. If the shear stress is not to exceed 60 MN/mm²…

A: Given that , P=300kW N=80 rpm Maximum shear stress = 60MN/mm2 internal diameter = 0.6 × external…

Q: A 7/8 in. diameter shaft made out of ductile material is used to transmit power from motor. The…

A: given diameter of the shaft, d=78inch=0.875inchmaximum allowable sheer stress, ζhallow=14.5ksiRPM,…

Q: A solid shaft in a rolling mill transmits 30kW at 100 rpm. Find the diameter in mm of the shaft so…

A: Answer: The diameter of the shaft is 63.35 mm. Hence, the correct answer is option (c).

Q: In a gearbox, a spur gear is mounted on a shaft at equal distances from two supporting bearings. The…

A: Hghh

Q: The maximum shearing stress that is present in a 2 in. diameter shaft subjected to 2200 in-lb is how…

A: Given data: Diameter of the shaft, d=2 in Torque applied on the shaft, T=2200 in.lb.

Q: EXERCISES 1. A shaft running at 400 rp.m. transmits 10 kW. Assuming allowable shear stress in shaft…

Q: Find the diameter of a solid steel shaft to transmit 43kW at 5.25 rps. The ultimate shear stress for…

A: The shaft is a device which is used to transmit power from one place to another. The torque…

Q: What is the maximum power P (kW) that can be transmitted by a shaft hollow (do = 50 mm, di = 40 mm)…

A: Outer diameter of shaft= 50mm Inner diameter of shaft= 40mm Rotational Speed of shaft= 600 rpm…

Q: A shaft made of steel receives 7.5 kW power at 1500 1.p.m. A pulley mounted on the shaft as shown in…

Q: In an industrial machine, two shafts have to be connected by using a muff coupling. The shaft…

A: Given,

Q: (12) A Ø50mm shaft is 3.0m long& receives 45kW from a pulley mounted @ 2.0m form the left end. A…

A: The schematic diagram of the shaft is Given data, Diameter of the shaft, d = 50 mm Length of the…

Q: A hollow steel shaft is stressed to 55 MPa by a torque of 100,000 ft-lb. If the inside diameter is…

Q: A shaft running at 400 r.p.m. transmits 10 kW. Assuming allowable shear stress in shaft as 40 MPa,…

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: A shaft is used to transmit 24 kw at a speed of 1,779 rev/min. Using a maximum allowable shear…

Q: 8.2 (A). Calculate the dimensions of a hollow steel shaft which is required to transmit 750 kW at a…

Q: A circular shaft of 60 mm diameter is running at 150 r.p.m. What will be the torque transmitted by…

A: Given, Diameter of shaft = d = 60 mm Shear stress in the shaft = τ = 80 MPa From the relation…

Q: A single cylinder engine operating at 1,500 rpm develops a torque of 10 N- m. The Friction power of…

A: Given:N=1500 rpmT=10 N.mFP=0.5 kW

Q: A shaft of diameter 40 mm is subjected to 360 N-m torque. The length of the shaft is 10 cm.…

A: Given data: The diameter of the shaft, d = 40 mm. The torque subjected to the shaft, T = 360 N-m.…

Q: Find the maximum stress developed in a stepped shaft when it is subjected to a: i) Torque of "T" Nm.…

Q: 3. Find the diameter of a solid steel shaft to transmit 27 kW at 300 r.p.m. The ultimate shear…

A: Given:-Power, P=27 kWSpeed, N=300 rpmUltimate shear stress, τu=360 MPaFactor of safety, FOS=8Ratio…

Q: Q1. Find the diameter of a solid steel shaft to transmit 30 kW at 250 r.p.m. The ultimate shear…

Q: 3. A steel shaft transmits 30KW at 1500rpm. Considering allowable shearing stress of degrees 351.6…

Q: A keyed gears delivers a torque of 912.4 N-m thru its shaft of 63.5 mm outside diameter. If the key…

A: GivenT=912.4Nmd=63.5mmt=15.875mmw=11.1125mmτ=61.2MPaσ=98.8MPa

Q: (a) A solid shaft of 220 mm dia is to be repiace dia being 2:1. Find the size of hallow shaft, if…

A: The shear stress developed in a solid shaft due to applied torque T is given by the formula-…

Q: 1. A shaft running at 400 r.p.m. transmits 10 kW. Assuming allowable shear stress in shaft as 40…

A: Given data, P= 10 KW=10000W τ=40 MPa =40000000 N/m² N= 400 rpm

Q: The outer diameter of the shaft is 175 mm and the diameter ratio is 1.25. Find the polar modulus of…

Q: 45. A geared turbine unit delivers 18,500 kW at the bull gear coupling at full power with a…

A: Find the mechanical losses at 35 km/hr.

Q: shaft in torsion only is to transmit 2500 hp at 570 rpm. Its material’s allowable shear stress is 10…

A: as per guidelines we need to answer only first 3 subparts

Q: A shaft running at 400 r.p.m. transmits 10 kW. Assuming allowable shear stress in shaft as 40 MPa,…

A: GivenN=400rpmP=10kWσa=40MPa

Q: A 7/8 in. diameter shaft made out of ductile material is used to transmit power from motor. The…

Q: Design a suitable diameter for a circular shaft required to transmit 90 kW at 180 r.p.m. The shear…

A: GIVEN DATA- MAXIMUM SHEAR STRESS = 70MPa POWER P=90KW SPEED N=180 r.p.m. MAXIMUM TORQUE = 140% OF…

Q: The steel alloy shaft having a diameter of 38 mm is used to transmit torque, T as shown in Figure…

Q: Problem 1

A: Due to the torques at point B, C, D, E, and G, there exists a reaction torque at point A.Sign…

Q: The solid steel shaft is supported by the frictionless customer on D and E. This system The mile…

A: Given: Maximum power transmitted by the shaft=5kW Speed of the shaft N=100rps Solution: Speed of the…

Q: A hallow steel shaft 2540 mm long must transmit torque of 34 KN-m. The total angle of twist must not…

A: Given that, for a hollow shaft, L = 2540 mm T = 4 kN-m Maximum angle of twist = 3 degrees Maximum…

Q: A Wind Turbine has a maximum output of 2MW at a speed of 20 rpm. A shaft of length 2m made of EN8…

A: Given: Maximum power=2×106W Speed=20rpm or 2.094rad/s Design stress=240MPa Length of the shaft=2m…

Q: a solid shaft is transmitting 1 mw at 240 rpm determine the daimeter of shaft exceed the mean of…

A: Shear stress produced by torque vary from zero at center of cross-section to maximum at surface in…

Q: In a gearbox, a spur gear is mounted on a shaft at equal distances from two supporting bearings. The…

A: Given:Maximum power transmit, P=3 kWSpeed of shaft, N=3600 rpmGear contact angle, φ=20oPitch…

Q: the shearing stress caused by a torque of 700 N m if dimension a =75 339. A tube 3 mm thick has the…

Q: applied, find this torque, the maximum shear stress, and the angle of twist per unit length. G = 85…

A: for solution refer below images. NOTE:- generally value of modulus of rigidity (G) is in Gpa, but in…

Q: A hollow steel shaft 2540 mm long must transmit a torque of 34 kN-m. The total angle of twist must…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

This engine is used in a hoist. Motor 2.5 kW
with the help of gears with a power of and n = 500 rpm.
transmits. If the shear strength of the AB shaft is τa = 160 MPa;
a) Find the diameter of AB shaft with 1.4 times safety.
b) Find the maximum force F the engine can carry.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A torque T is applied to a thin-walled tube having a cross section in the shape of a regular hexagon with constant wall thickness t and side length b (see figure). Obtain formulas for the shear stress rand the rate of twist
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (sec figure). If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (T0) that may be applied at section C? Find (T0)max if the maximum angle of twist is limited to 0.55º. Let G = 10,600 ksi.
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.