1. Three series resistors are connected across a voltage source Vs. The voltage drops across each resistor are measured and found to be 4.5 V, 6.4 V, and 13.1 V. What is the value of the voltage source Vs? 2. Four resistors are in series with a 100-V source. The voltage drops across three of the resistors are 10 V, 20 V, and 40 V. If the resistance of the fourth resistor is 300 Ω, what is the current through the circuit? 3. The voltage source in circuit is supplying 100 mA of current. Determine IBA, ,VAD and VBC, if ICD = 50 mA. 1. Three series resistors are connected across a voltage source V.. The voltage dropsacross each resistor are measured and found to be 4.5 V, 6.4 V, and 13.1 V. What isthe value of the voltage source V,?2. Four resistors are in series with a 100-V source. The voltage drops across three ofthe resistors are 10 V, 20 V, and 40 V. If the resistance of the fourth resistor is 300 Q,what is the current through the circuit?3. The voltage source in circuit is supplying 100 mA of current. Determine IBa, VAD:and V BCif IcD= 50 mA.A400 2600 2200 2E+ )100 V

Since you have asked multiple question, we will solve the first question for you. If you want any…

Three series resistors are connected across a voltage source Vs. The voltage drops across each resistor are measured and found to be 4.5 V, 6.4 V, and 13.1 V. What is the value of the voltage source Vs?

Three series resistors are connected across a voltage source Vs. The voltage drops across each resistor are measured and found to be 4.5 V, 6.4 V, and 13.1 V. What is the value of the voltage source Vs?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter8: Combination Circuits

Section: Chapter Questions

Problem 1PA: A circuit contains a 1000- and a 300- resistor connected in series with each other. The total...

See similar textbooks

Related questions

Q: A 9-ohm resistance is connected in parallel with a 14-ohm resistance. Another set, a 7-ohm and an…

Q: What is the equivalent resistance of the three resistors that are in A. parallel with each other? |…

A: A. The equivalent resistance of three resistors that are in parallel is given by,…

Q: Three resistor are connected in parallel to a 20V-supply. The resistances are R1=100, R2=8 and R3.…

Q: Three series resistors are connected across a voltage source V.. The voltage drops across each…

A: In the question We are solving all problem using the KCL and KVL . In the series , current are equal…

Q: If four 1KΩ-resistors will be in parallel, what is the total resistance? *

Q: Two resistors are to be combined to form an equivalent resistance of 1,000 0. The resistors are…

A: Please find the detailed solution in below images

Q: What is the value of a resistor that must be connected in parallel across a 100kN resistance to…

A: if R1 and R2 are in parallel then total resistance is RT 1RT=1R1+1R2 Given R1 =100…

Q: A 6 – ohm resistor is connected in series to a parallel connection of a 30 – ohm resistor and a…

A: To find the value of variable resistor R , such that power taken by the 6-ohm resistor is equal to…

Q: Draw the flow of current for the given circuit and discuss thouroughly how the five voltage drop are…

A: The asked problem is based on the concept of kirchhoff's voltage law ( kvl ) , kirchhoff's current…

Q: How much resistance R1 must be added in series with a 400 Ω R2 to limit the current to 0.25 A with…

Q: Suppose we construct a voltage divider circuit as shown in Figure 1.1 where the voltage source V₁ is…

Q: Draw the circuit diagram and determine the equivalent resistance of 3 resistors rated as R1 = 5…

A: The detailed solution is attached with.

Q: Given five resistors in series-parallel connection with the following data, what is the total…

Q: When 10 cells in series are connected to the ends of a resistance of 59Ω, the current is found to be…

A: Given that = Number of identical cells are (n) = 10. When cells are connected in series to 59Ω…

Q: What is the resistance of R₁ in the circuit below?

Q: What is the value of unknown resistance to be connected in parallel to a 30kΩ to reduce the total…

A: In this question, What is the value of unknown resistance R2 to be connected in parallel to a 30kΩ…

Q: Question 4 How to transform a current source in parallel with a resistor R to a voltage source? A…

A: Source transformation: A voltage source in series with a resistor across a terminals can be…

Q: Two resistors, R1 = 100 0 and R2 = 200 Q are connected in series, if the voltage across R2 is 20 V,…

Q: If two resistors are connected in parallel and R1 is shorted, what are the current and voltage in…

A: Note: As per the policy we can solve only one question at once, please re-upload the remaining…

Q: - Two resistances of 10 and 15 ohms, each respectively are connected in parallel. The two are then…

A: In the circuit, 2 resistances are connected in parallel and equivalent connect to 5 ohm resistance…

Q: Two batteries, A and B, are connected in parallel and an 80 ohm resistor is connected across the…

Q: Five resistors are connected in series-parallel. R1, R2, R5, and the parallel combination of R3 and…

A: The solution can be achieved as follows.

Q: A 10-ohm resistance is connected in parallel with a 12-ohm resistance. In another set, two 9-ohm…

Q: What is the power dissipated by the 24 -Ω resistor?

Q: In the circuits, Determine: a. the total resistance (RT) of the circuits in KΩ. b. the current…

A: In the circuits, Determine: a. the total resistance (RT) of the circuits in KΩ. b. the current…

Q: Two resistors when connected in series have a total resistance of 10 ohms. If they are connected in…

A: Please refer the attached images for the complete answer..

Q: Two resistors R₁ and R2 (where R₁ > R₂) are connected in series to an ideal battery. Which of the…

Q: There is a constant current source whose value is 8 A now there are three resistors connected to it…

A: Draw the circuit and than using nodal analysis find the voltage across the parallel connected…

Q: Initially, two resistors R1 and R2 are connected in series. The connection of the terminals of R1…

Q: Given the voltage source values are within 0 to 12 V, and the values of resistors are: R1= 5k2, R2=…

Q: 22. The figure shows five combinations of identical resistors. Rank in order, from largest to…

A: To find the equivalent resistance of a complex circuit, it is important to convert complex circuits…

Q: 3. Two resistances of 100 and 150respectively are connected in parallel. The two are then connected…

Q: An electrical circuit includes a voltage source and two resistances (50 and 75 Ω) in parallel.…

Q: vo resistors R₁ and R₂ (where R₁ = R₂) are connected in series to an ideal battery. Which of the…

A: The total resistance= R1+R2 = 2R1=2R2 The total resistance is…

Q: Two resistors are connected in series and have the values 10000 Ω ±5 % and 1000000 Ω ±10%. What is…

Q: 1. Three series resistors are connected across a voltage source Vs. The voltage drops across each…

A: Note: We’ll answer the first question since the exact one wasn’t specified. Please submit a new…

Q: Determine the following: a) Total resistance of the circuit, Total Current and Total Power of the…

A: In this question, We need to A) Total resistance of the circuit, Total Current and Total Power of…

Q: Two resistors R1 and R2 are in series and have resistances of 44 ohms and 9 ohms respectively. The…

Q: What is true about the current through each resistor in the circuit below? If the resistances are…

Q: equal to the power taken by the 4-ohm resistor. 2. A 20-ohm resistance is connected in parallel with…

A: The solution is given below

Q: "What is the equivalent resistance of ten resistors in series, one of resistance 1? and one of…

A: The equivalent resistance of ten resistors in series, one of resistance 1 ohm and one of resistance…

Q: Draw the flow of current for the given circuit and discuss thouroughly how the three voltage drop…

Q: How much resistance R1 must be added in series with a 400 Ω R2 to limit the current to 0.25 A with…

Q: Two resistors Rị and R2 are connected in parallel as shown in the figure. R R: If the resistance R¡…

Q: An electric circuit with two DC power supplies is shown in Figure A (E1 and E2). Assume that E1 =…

A: Ans. Shown below.

Q: R1 = 100.0 ± 0.12, %3D R2 = 50 ±0.032 %3D

Q: a. An electrical engineer was given a contract to design a device with the following specifications:…

A: Given a device to be designed with the following specifications Source voltage of 240 V Three…

Q: The full scale value is 20 Volt and it is required to measure a maximum of 1000 Volt with a…

A: Should the resistance be connected in series or parallel to the voltmeter? Briefly explain the…

Q: 5 batteries are connected in parallel to supply current to a load resistance for heating. Each…

Q: Two resistors are connected in series. One resistor has a resistance of 1000 Ω, and the other…

A: Fig: Circuit for given specification apply KVL in the circuit shown above…

Concept explainers

Current Division Method

The generalized current divider formula is given by the following relation below,

Question

1. Three series resistors are connected across a voltage source V_s_. The voltage drops across each resistor are measured and found to be 4.5 V, 6.4 V, and 13.1 V. What is the value of the voltage source V_s?

2. Four resistors are in series with a 100-V source. The voltage drops across three of the resistors are 10 V, 20 V, and 40 V. If the resistance of the fourth resistor is 300 Ω, what is the current through the circuit?

3. The voltage source in circuit is supplying 100 mA of current. Determine I_BA_{, ,}V_AD and V_BC_, if I_{CD =} 50 mA.

1. Three series resistors are connected across a voltage source V.. The voltage drops
across each resistor are measured and found to be 4.5 V, 6.4 V, and 13.1 V. What is
the value of the voltage source V,?
2. Four resistors are in series with a 100-V source. The voltage drops across three of
the resistors are 10 V, 20 V, and 40 V. If the resistance of the fourth resistor is 300 Q,
what is the current through the circuit?
3. The voltage source in circuit is supplying 100 mA of current. Determine IBa, VAD:
and V BC
if IcD
= 50 mA.
A
400 2
600 2
200 2
E
+ )100 V

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Four resistors having values of 270,330,510, and 430 are connected in parallel. What is the total resistance in the circuit?
You are an electrician on the job. The electrical blueprint shows that eight 500-W lamps are to be installed on the same circuit. The circuit voltage is 277 V and is protected by a 20-A circuit breaker. A continuous-use circuit can be loaded to only 80% of its rating. Is a 20-A circuit large enough to carry this load?
Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l33.2AI4RT3.582R116R210R3R420PTP1P2P3P4
How much resistance R1 must be added in series with a 400 Ω R2 to limit the current to 0.25 A with 120 V applied? Which statement is correct about a parallel circuit? a)The source voltage is equivalent to the voltage across each load. b)The total current is equivalent to the sum of the branch currents c)The total resistance is equivalent to the sum of the reciprocal of each load resistance. d)The source voltage is equivalent to the sum of the individual voltage drops. A heater element rated for 1000 watts and 120 volts is operated from a 100-volt source. As a result, its:a)resistance will decrease.b)resistance will remain the same.c)wattage will increase.d)current will increase.
Two resistors A and B are connected in series with a 220-V DC source. a voltmeter with an internal resistance of 10k Ohms is connected across resistor A, the instrument reads 100V and when connected across resistor B, it reads 80V. Find the value of the two resistances in series. please show complete solution.
Two resistances of 10 and 15 ohms, each respectively are connected in parallel. The two are then connected in series with a 5-ohm resistance. It is then connected across a 12-V battery, what are the total resistance, current and power?
Using only source transformation and without eliminating ix, reduce the circuit in Figure to a single voltage source and a single resistor, then obtain ix using Ohm's law. A) What is the value of the source voltage in V and what is the value of the resistor in Ω? B) What is the value of ix in A?
A voltage divider of 50 ohms is connected across a 100 V DC source. A load resistance of 10 ohms is connected across a tap in the potential divider and the negative of the source. If a current of 4 A flows towards the load, what is the current supplied by the source? (Remember, a voltage divider is a network of resistors that are connected in series the purpose of which is to divide a voltage into each of the resistors.) Show complete solution.
Find the total resistance of two resistors in parallel if R1 = 1700 Ω and R2 = 800 Ω
If two resistors are connected in parallel and R1 is shorted, what are the current and voltage in R2? Explain If two resistors are connected in parallel and R1 is open, what are the current and voltage in R2? Explain Which has more excellent equivalent resistance, those resistors in parallel or those in series? Explain
1. A 20-ohm resistor, a 30-ohm resistor, and a resistor R are connected in parallel to form an equivalent resistance of 4 ohms. Find R and the current it carries if a 6-A current source is connected to the combination. 2. A current divider consists of 10 resistors in parallel. Nine of them have equal resistances of 60 kilo-ohms and the tenth is a 20 kilo-ohm resistor. Find the equivalent resistance of the divider, and, if the total current entering the divider is 40mA, find the current in the tenth resistor.
The total current drawn by a circuit consisting ofthree resistors connected in parallel is 12 A. Thevoltage drop across the first resistor is 12 V, thevalue of the second resistor is 3 ohms, and the power dissipationof the third resistor is 24 W. What are the resistances of the first and third resistors?