To create a Polyline or Polygon geometry object, which two objects must first be created?

Q: can you do it in polygon

A: Given vectors : A :  2 kph 45°N of E B :  2.8  kph 58°E of S C :  5.1  kph 28°W of S D : 3.2  kph…

Q: A point is on the x-axis. It's y- coordinate and z-coordinate are respectively

A: If a point A is on the X-axis in three-dimensional coordinate system, then Point A is (x, 0, 0,)…

Q: 3- The front, top and right side views of an object are shown below. Freehand sketch the partial…

A:

Q: 1. Draw the followings views in 3rd angle projection in PARTIAL AUXILIARY & DO NOT Dimensions.

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Question 1/ Answer by True or False for the following statements Loft command is used to create a 3D…

A: It is true that loft command is used to create a 3D solid or surface in the space between several…

Q: Sketch the orthographic projection as per the answer arrangement (a) top view (b) side view (C)…

A:

Q: 3- The front and top views of an object are shown below. Freehand sketch the partial auxiliary view…

A: Given front and top view

Q: Q1: Draw the orthographic Projections of given object.

A: Orthographic Projection

Q: Given FRONT and TOP views of the object: • Identify in both views the larger inclined surface that…

A:

Q: * = pw 2 gm/cm³ O 1 gm/cm³ O 4 gm/cm³ O 3 gm/cm³ O 5 gm/cm³ O

A: Given:-  Density of water = ................. g/cm3   Options Provided:-  2 1 4 3 5

Q: 2. Explain how to compile and run a program with the help of a diagram

A: Given Data : Program Compile and Run

Q: Briefly write down the  steps on how to generate (sketch) an involu

A: Involute Profile

Q: Create a free hand isometric drawing of the three objects

A: Free hand isometric drawing of all three components are drawn below...

Q: In the FILLET command, when selecting the objects to fillet, holding down the <Shift> key: a.…

A: By holding the <Shift> key before selecting the second object when using a FILLET command, the…

Q: In the TRIM command, when selecting objects to trim, holding downthe <Shift> key: a. Allows…

A: By holding the <Shift> key while using the TRIM command, it will be inverted to the opposite…

Q: SKETCH THE 2D FIGURE IN AUTOCAD DRAWING AND USE THE 2D SKETCHING TO FIGURE OUT THE BELOW SKETCH

A:

Q: Projective Geometry: Draw two of same object, one near and one far. The objects at the back should…

A:

Q: The given sketch is a cross section view of bracket. Sketch the 2D sketch of the below figure using…

A:

Q: Draw the top view, side view, and front view of the figure below.

A: The required Front view , Top view and Side are drawn using third angle method of projection.

Q: Draw an isometric sketch of the object from the viewpoint W-Corner.

A: According to the details provided in the question, we need to calculate the isometric view.

Q: Orthographic projection of the component show below

A:

Q: Based on the following orthographic projections for each object, generate a full-scale isometric…

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: To make the circle in an Isometric drawing which geometric option we select from menu bar and why?…

A: 1.To make an isometric drawing of circle we select it from menu bar because we do not have any…

Q: .Draw a figure showing a helicoidal joint pointed in the positive x-axis  direction of a 3D space?

A:

Q: n the figure, front (1st picture) and left (2nd picture) views of a machine part are given. Based on…

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: Hello, I need help with the answer of 3.14 from the picture, please.

A:

Q: Draw only Full section Front view of the given object.Draw the diagram on grid sheet

A: There are various orthogonal projections of the image. The front view is one of them. To understand…

Q: Based on the following orthographic projections for each object, generate a full-scale isometric…

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: P2-13) Sketch the front, top and right side views of the following object. Use the grid provided.

A:

Q: HomeWork: Draw the shape below using the Front View for drawing in 2D and then the Southwest…

A:

Q: Need you to draw orthographic views of this object.

A: The required orthographic views are drawn using third angle method of projection.

Q: Using engineering graphics and drafting concepts . Draw the isometric view of the given orthographic…

A: given orthographic view

Q: Instructions: Use third-angle projection and create three-view drawings for the following 3D objects…

A: problem fig,

Q: Q1) Create an orthographic projection of the following object. Draw the three standard views-

A:

Q: Q2: Draw the Full Sectional Front view and Top View of the given object?

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: a diagonal of a polygon is a line segment that connects nonadjacent vertices of the polygon.in the…

A: Let us assume that the number of sides of the given polygon is 'n'. We can find the number of…

Q: prepare and submit an oblique drawing based on the 2D Multiview object drawing.

A: We get an oblique view or oblique projection by taking 45° from the side

Q: draw the orthogonal projections of the displayed object

A: According to the details provided in the question, we need to draw three projection views.

Q: Draw (hand drawing) three views of the following components, in third angle projection (including…

A: Draw the all three diagrams of figure (1).

Q: In order to produce the L-Holder shown you must read the dimensions on an Engineering Drawing.…

A: Given:- Engineering drawing of L-holder with dimensions Top view, Front view, Side view, and…

Q: 17-5B pencil is lighter than 5H pencil. O True O False 8- This figure shows center line. O True O…

A: (17) In this problem, it is asking that 5B pencil is lighter than 5H or not.

Q: Create an oblique drawing of this object

A:

Q: Make a working drawing of one of the parts shown in below figure Refer to the drawing for setup of…

A: Draw complete top and front views and a partial auxiliary view. Hidden lines may be addedfor…

Q: us esecale (2-2) to draw the orthographic projections (top view, front view, side) for the…

A: Find Draw the orthographic projections of the given object by using a scale (2.2).

Q: Sketch the 2D figure using AutoCAD and mention all the dimensions, colour the hatched lines if there…

A:

Q: question from ENGINEERING DRAWING BY N.D BHATT     Write all steps of drawing following 3D model in…

A: Given: geometry as shown

Mechanical Drawings

A mechanical drawing is described as a technical drawing created by engineers following standard layout conventions, terminology, interpretation, and many other factors. It is also known as an engineering drawing.