To loosen a rusty nut, a 20.00-N force is applied to the wrench handle at angle o=40° and at a distance of 0.25 m from the nut. Find the magnitude and direction of the torque applied to the nut. nut R R

To loosen a rusty nut, a 20.00-N force is applied to the wrench handle at angle o=40° and at a distance of 0.25 m from the nut. Find the magnitude and direction of the torque applied to the nut. nut R R

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter8: Rotational Equilibrium And Dynamics

Section: Chapter Questions

Problem 2P: A worker applies a torque to a nut with a wrench 0.500 m long. Because of the cramped space, she...

See similar textbooks

Related questions

Q: Three uniform spheres are fixed at the position shown. What are the magnitude and direction of the…

A: Given : my=1kg mx=1kg mxy=2kg mP=0.015kg rx=0.5m…

Q: 0. Calculate the torque vector of the following force (N) and position (m) vectors: a. 7 = 5î + 10î;…

A: The torque vector is given as, a) The torque vector is given as,

Q: A car initially traveling at 32.2 m/s undergoes a constant negative acceleration of magnitude 1.90…

A: a) The traveled distance is, Thus, the required number of revolution is,

Q: Q.3: Calculate the acceleration of the center of mass of the hoop rolling down the inclined plane…

Q: (a) Find the new angular speed of the student. rad/s (b) Find the kinetic energy of the rotating…

A: Given, Mass of dumbbell, md=2.97 kg, distance of dumbbell when arms extended, x1=1.06 m, angular…

Q: A 2.90 kg bucket is attached to a disk-shaped pulley of radius 0.131 m and mass 0.792 kg. If the…

A: A. Linear acceleration a = 8.622 m/s2 B. Angular acceleration= 65.82 rad/S2

Q: The tires on a new compact car have a diameter of 2.0 ft and are warranted for 62,000 miles. (a)…

Q: When tightening a bolt, you push perpendicularly on a wrench with a force of 156 N at a distance of…

A: Given, F = 156 N d = 0.12 m Torque = F*d*sin A Since the force is applied perpendicular to the…

Q: The tires on new compact car havea diameter of 2.0 ft and are warranted for 60 000 miles, (a)…

A: Answer Given data Diameter of the tire d= 2 ft Warranty of the tire x=60000 miles a Angle rotated by…

Q: 3. A particle located at the position vector r = (i+ I)m has a force F = (2i + 3j) N acting on it.…

A: The cross product of position vector and force. The unit of torque is newton-meterN·m.…

Q: It would be expected that as the angle of an incline increases, the coefficient of static friction…

Q: If the torque required to loosen a nut that is holding a flat tire in place on a car has a magnitude…

Q: (a) After the combination rotates through 90 degrees, what is its rotational kinetic energy? (b)…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: An engine delivers 175 hp to an aircraft propeller at 2400 rev/min. (a) How much torque does the…

A: Given- Power delivered by engine to propeller, P = 175 hp = 175 x 745.7 W = 130497.5 W Angular…

Q: Question 8 The figure shows the set up of E103 for a ring pulley. Which of the followin M T R Which…

A: From FBD and Newton's laws of motion, mg - T = ma So, T = mg - ma And TR = Iα T = Iα/R

Q: A marry-go-round that has a mass of 100 kg and a radius of 2 m is rotating at 1 rad/s. (a) What is…

Q: A car with tires of radius 31 cm drives on the highway at 65 mph. (a) What is the angularspeed of…

A: Given data: The radius of car’s tires is: r = 31 cm = 0.31 m The velocity of car is: Vcar = 65 mph =…

Q: The figure shows the set up of E103 for a disk pulley. Which of the following gives the tension in…

Q: ghtly stretched "high wire" is 35 m long. It sags 2.1 m when a 5 kg tightrope walker stands at its…

A: GivenLength of wire, L=35 mWire sags, x=2.1 mMass of walker, m=64.5 kg

Q: A bowling ball rolls up a ramp 0.5 m high without slipping to storage. It has an initial velocity of…

A: Given data We have to find the final velocity of the ball at the top of the ramp And its value if…

Q: (I) A 52-kg person riding a bike puts all her weight on eachpedal when climbing a hill. The pedals…

Q: Constants Force F = -12 ¡N is exerted on a particle at ř = (3i +5j)m. Part A What is the torque on…

Q: A solid cylinder rolls up an inclined plane of angle of inclination 30°. At the bottomof the…

A: (a) The cylinder has both rotational and translational kinetic energyWrite the expression for…

Q: QI. To insert the small eylindrical part into a elose-fitting cireular hole, the robot arm aust…

A: If we observe the figure carefully we would find that it makes 15° with parallel AB rod. And angle…

Q: 3. To loosen a rusty nut, a 20.00-N force is applied to the wrench handle at angle o=40° and at a…

Q: hi, can you pls explain this to me? our topic is Torque or moment of a force. Thank you a) Describe…

A: Translational Equilibrium: An object is said to be in translational equilibrium if the velocity of…

Q: An ice skater with moment of inertia, I is rotating with angular speed, W. The skater pulls her arms…

A: Given: The intial moment of inertia of the system is I. The initial angular speed is ω. The final…

Q: The angular speed of a rotor in a centrifuge increases from 422 to 1350 rad/s in a time of 4.41 s.…

Q: An object is acted on by a single nonzero force of magnitudeF. (a) Is it possible for the object to…

A: Part (a):Force acting on any object can be given by Newton’s second law as follows,

Q: A cylindrical object (I =mr) rolls down a ramp. %3D a Derive an expression for the linear…

Q: A centrifuge in a forensics laboratory rotates at an angular speed of 3,750 rev/min. When switched…

A: Given data *The initial angular speed is ωi=3750 rev/min=3750×2π60 rad/s=392.69 rad/s *The total…

Q: A rope is wrapped around a pulley which is best modeled as a ring. Ithas a mass M and radius R. The…

Q: 9) A hex-nut needs to be tightened with a wrench (Fig below) a) Which force (red arrow) shown in the…

A: Formula of torque is as follows; τ=rFsinθ…

Q: What is the final velocity (in m/s) of a hoop that rolls without slipping down a 6.50-m-high hill,…

Q: (II) (a) A grinding wheel 0.35 m in diameter rotates at 2200 rpm. Calculate its angular velocity in…

A: a) The value of angular velocity, ω=2200rpmω=2200(2π60)rad/s=230.2rad/s

Q: A 154 g frisbee is 34 cm in diameter and has half its mass spread uniformly in a disc, and the…

Q: A car initially traveling at 24.2 m/s undergoes a constant negative acceleration of magnitude 1.70…

A: (a) How many revolutions does each tire make before the car comes to a stop. (b) What is the angular…

Q: When tightening a bolt, you push perpendicularly on a wrench with a force of 161 N at a distance of…

A: Torque is given by Torque (τ) = Force(F)× perpendicular distance between centre of bolt and the…

Q: A rope is wound around a shaft 10 cm in diameter. If a pull of 500 N is exerted on the rope, what…

A: Torque is the measure of the force that can cause an object to rotate about an axis. τ=r×F=rF sinθ

Q: What is the final velocity (in m/s) of a hoop that rolls without slipping down a 6.00-m-high hill,…

Q: b. A wheel on an extremely low friction slanted surface will slide without rotating. However, if the…

A: When a wheel is on a slanted surface, the force due to gravity acts on its center of mass. This…

Q: . A coin is sitting on a record as sketched in Figure D. It is found that the coin slips off the…

A: 10. radius, r = 15 cm= 0.15 m frequency, f = 0.3 rps

Q: a) What is the magnitude of the pulley's angular acc |rad/s²

A: Givenm1=m2=m=8 kgr=2.9 cmI=8×10-4 kg m2θ=0.150 radt=60 ms=

Q: You have a grindstone (a disk) that is 82 kg, has a 0.325-m radius, and is turning at 80 rpm, and…

Q: When tightening a bolt, you push perpendicularly on a wrench with a force of 150 N at a distance of…

A: Given : Perpendicular distance →d=0.175 m Force→F=150 N Standard data used : 1 N= 0.738 pound-foot

Q: Problem 7: Consider the pulley and mass configuration shown. The pulley can be modeled as a solid…

A: The solution is given below

Concept explainers

Torque

Torque is the rotational equivalent of linear force in physics and mechanics. Based on the course of study, it is also known as the moment of force, rotational force, or turning effect.

Question

3. To loosen a rusty nut, a 20.00-N force is applied to the wrench handle at
angle o=40° and at a distance of 0.25 m from the nut. Find the magnitude and
direction of the torque applied to the nut.
nut
R

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

When tightening a bolt, you push perpendicularly on a wrench with a force of 165 N at a distance of 0.140 m from the center of the bolt. How much torque are you exerting in newton-meters (relative to the center of the bolt)?
Under what conditions can a rotating body be in equilibrium? Give an example.
A worker applies a torque to a nut with a wrench 0.500 m long. Because of the cramped space, she must exert a force upward at an angle of 60.0 with respect to a line from the nut through the end of the wrench. If the force she exerts has magnitude 80.0 N, what magnitude torque does she apply to the nut?
Give an example in which anal forte exerts a large torque. Give another example in which a large force exerts a small torque.
The cylindrical head bolts on a car are to be tightened with a torque of 62.0Nm . If a mechanic uses a wrench of length 20 cm, what perpendicular force must he exert on the end of the wrench to tighten a bolt correctly?
What three factors affect the torque created by a force relative to a specific pivot point?
(a) Give an example in which the net force acting on an object is zero and yet the net torque is nonzero, (h) (five an example in which the net torque acting on an object is zero and yet the net force is nonzero.
A boy rides his bicycle 2.00 km. The wheels have radius 30.0 cm. What is the total angle the tires rotate through during his trip?
A worker applies a torque to a nut with a wrench 0.500 mlong. Because of the cramped space, she must exert a forceupward at an angle of 60.0° with respect to a line from thenut through the end of the wrench. If the force she exerts hasmagnitude 80.0 N, what magnitude torque does she apply tothe nut?
1. Ned tightens a bolt in his car engine by exerting 12 N of force on his wrench at a distanceof 0.40 m from the fulcrum. How much torque must Ned produce to turn the bolt?
A force of 45.0 Newtons is applied at a right angle to a lever which is 1.50 meters long. Determine the magnitude of the applied torque.
1. A force of 200 N is applied perpendicularly to and at the end of a wrench 0.4 m long. Compute for the amount of torque created by force?