To use the principle of linear impulse and momentum to relate a force on an object to the resulting velocity of the object at different times. The equation of motion for a particle of mass m can be written as ∑F=ma=mdvdt By rearranging the terms and integrating, this equation becomes the principle of linear impulse and momentum: ∑∫t2t1Fdt=m∫v2v1dv=mv2−mv1 For problem-solving purposes, this principle is often rewritten as mv1+∑∫t2t1Fdt=mv2 The integral ∫Fdt is called the linear impulse, I, and the vector mv is called the particle's linear momentum.   A jetliner of mass 8.60×104 kg is in level flight when it encounters a downdraft (a downward wind) that lasts for 1.40 s . The vertical component of the jetliner's velocity is 74.0 m/s after the downdraft subsides. What is the downdraft's average force, F, on the jetliner?

Question

To use the principle of linear impulse and momentum to relate a force on an object to the resulting velocity of the object at different times.

The equation of motion for a particle of mass m

can be written as

F=ma=mdvdt

By rearranging the terms and integrating, this equation becomes the principle of linear impulse and momentum:

∑∫t2t1Fdt=mv2v1dv=mv2−mv1

For problem-solving purposes, this principle is often rewritten as

mv1+∑∫t2t1Fdt=mv2

The integral ∫Fdt is called the linear impulse, I, and the vector mv is called the particle's linear momentum.

 

A jetliner of mass 8.60×104 kg is in level flight when it encounters a downdraft (a downward wind) that lasts for 1.40 s . The vertical component of the jetliner's velocity is 74.0 m/s after the downdraft subsides. What is the downdraft's average force, F, on the jetliner?

Expert Answer

Want to see the step-by-step answer?

Check out a sample Q&A here.

Want to see this answer and more?

Experts are waiting 24/7 to provide step-by-step solutions in as fast as 30 minutes!*

*Response times may vary by subject and question complexity. Median response time is 34 minutes for paid subscribers and may be longer for promotional offers.
Tagged in
Engineering
Mechanical Engineering

Related Mechanical Engineering Q&A

Find answers to questions asked by students like you.

Q: 13-56 Consider two rectangular surfaces perpendicular to each other with a common edge which is 1.6 ...

A: Given data:Length, L1 = 0.8 mLength, L2 = 1.2 mWidth, w = 1.6 mTemperature of horizontal rectangular...

Q: Which has a higher strength, polystyrene with a DP of 1000 or a DP of 5000?

A: Degree of polymerization (DP) is defined as presence the total monometric units in a polymer. It is ...

Q: Name three types of workpiece features that are well suited to using a rotary positioning device.

A: For performing milling operation at multiple angles the rotary devices are used. Basically, the rota...

Q: Please be very detailed

A: The room is heated electrically to keep a steady-state temperature. This heat is lost to the environ...

Q: This is a dynamics question. The answer is 481 mm.

A: The free body diagram of both the cars A and B is shown below:

Q: What does the "crossport relief valve" do in a hydraulic motor circuit ??

A: The basic function of crossport relief valve in motor circuit is –When the motor is started initiall...

Q: Explain why low-density polyethylene isgood for making grocery bags, but superhigh molecular weight ...

A: Low density polyethylene: Low Density Polyethylene (LDPE) is a type of polymer which has short and l...

Q: Is this a clearance or interference fit?

A: Clearance Fit : If upper limit of the shaft is less than lower limit of the hole, we can always have...

Q: Determine the magnitude of the pin force at B.

A: Consider the Ox, Oy, Bx and By be the x and y components of force at point O and B respectively. Dra...

Q: In company that designs road cars and heavy trucks, it important to make the proper selection of the...

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts i.e...

Q: Consider a Brayton cycle with a pressure ratio of 13, that receives 6.5 lbm/s of air at 75 ∘F. Assum...

A: The T-s diagram for actual Brayton cycle is given as   In the above diagram, the temperatures T2s a...

Q: Question in pic below. Specifically a dynamics problem.

A: Given data as per question Maximum allowed deflection,d = 0.2 m Speed of the vehicle,v = 4 m/s Mass ...

Q: A cylindrical rod of diameter 9.5 mm fabricated from a 2014-T6 aluminum alloy is subjected to rotati...

A: Given data: Diameter of rod = 9.5 mm Maximum load = 400 N Minimum load = -400 N Separation between t...

Q: Can you show how to solve this problem in both vector and scalar method

A: Drawing the free body drawing for the given problem,  

Q: Please find the question attached.

A: Shear strain is defined as the change in the angle in radian. Since the DB line remains horizontal, ...

Q: What is the MMC of shaft "C"?

A: MMC stands for Maximum Material Condition, which is the feature of the size of the object that descr...

Q: 4. A uniform rod of 0.90m length is used to suspend two masses as shown below. At what distance x sh...

A: Given data: Consider the diagram shown below for the given system.

Q: L1 PB 2 E2 L2 D2 Dimensions: L2 L1 D2 D1 17 mm 18 cm 23 cm 15 mm Problem Statement: The rod shown is...

A: Consider the following diagram showing the forces (loads) acting on the system of two rods of differ...

Q: You are given a sample of polypropylene and wish to find out the volume % crystallinity. You know th...

A: Given: Density of crystalline polypropylene, (ρC) = 0.946 g/cm3 Density of amorphous polypropylene, ...

Q: as shown in the attached figure, a block with mass m1 is attached to a massless ideal string. the st...

A: Click to see the answer

Q: Specifically a dynamics problem. Question and diagram in pic below.

A: The equation for the magnitude of the velocity The equation of radial velocity is

Q: Compute the total elongation of the bar shown in Figure P3-37 if it is made from titanium 3-37. Ti-6...

A: Reaction at A; Axial loading diagram: Now,

Q: To use the principle of work and energy to determine characteristics of a system of particles, inclu...

A: Given data as per question Mass of the block A = 56 KG Mass of the block B = 74 kg Coefficient of ki...

Q: The question in the picture is a dynamics question. Hint: vC = Lw (up), aC = 0.577Lw2 (up)

A: For the given mechanism, let the link makes an angle of phai with the horizontal as shown below, Th...

Q: To apply the principle of work and energy to a system of particles.  The principle of work and energ...

A: given: The mass of Block A = 12.0 lb The mass of block B = 41.0 b The inclined angles are 30.0 degre...

Q: This is a dynamics question.

A: Click to see the answer

Q: The side of a home can be modeled as a plane wall. The wall is 12 centimeters thick. If the outdoor ...

A: Click to see the answer

Q: A hollow aluminum cylinder made of 2014-T4 has an outside diameter of 2.50 in. and a wall thickness ...

A: Given data for aluminum cylinder 2014-T4  

Q: Hi there. From the attached question, I am wanting to solve for the following:  1. the j component o...

A: The vector resolution of the initial velocity u is drawn below.

Q: An industrial robot performs a machine loading and unloading operation. A PLC is used as the cell co...

A: Referring to the ladder symbols, X1: it is the limit switch. X2: It is a photocell. Set timer T1 to ...

Q: Fluid mechanics / please find the attached file.

A: The expression of rate of change in temperature at the house is written as

Q: This is a dynamics question.

A: Drawing the figure of the problem, and free body diagram.    

Q: I did a torsion test to experimentally calculate the brass modulus of rigidity. My experimental modu...

A: For determining the torsional properties of the material torsion test is performed. With the help of...

Q: Specifically a dynamics problem. Question in pic below.

A: We know that Acceleration = 10 t m/s2 Radius  = 0.5 m Time = 3 s  

Q: An emergency stop system is to be designed for a certain automatic production machine. A single "sta...

A:         Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for y...

Q: 3-17: A part for a truck suspension system is to carry a compressive load of 135 kN with the possibi...

A:   Given data as per question Compressive load = 135 KN

Q: 3.6 The force system acting on the machine part is equivalent to the single force R = 80i + 20j lb a...

A: The given system of force is –

Q: 4-9 Determine the force required to punch a slug hav- ing the shape shown in Figure P4-9 from a shee...

A: Punching force:

Q: (Mechanics and Materials Class) Problem 73: Find the reactions at the supports, and find the shear f...

A: Given: The cantilever beam having varying distributed load of 8.4 kN/m as shown in figure 1 part (a)...

Q: The question is the picture is a dynamics problem. Hint: vA = 5.16 ft/s, theta = 39.8 from the +y-ax...

A: Given data as per question Diameter of the pinion gear = 1.50 ft. Velocity of rack gear,vc = 4ft/s V...

Q: A machine having a mass of 4200 kg is supported 1-45. by three solid steel rods arranged as shown in...

A: Mass of the machine = 4200 kg = 4200*9.81 = 41202 N Diameter of the rod = 20 mm Free body diagram of...

Q: The 54-lb block rests on the rough surface for which the coefficient of kinetic friction is μk = 0.2...

A: Click to see the answer

Q: What are heat-treatable and non-heat-treatable aluminum alloys?

A: Heat treatable aluminum alloys: They consist of pure aluminum that is heated to a critical temperatu...

Q: An engineer is using the pliers shown below to twist a pin at P. Based on the parameters given, find...

A: Moment is defined as the product of force and the perpendicular displacement.

Q: Project 5: Automobile radiator, condenser, evaporator, air preheater, and cooling tower are common t...

A: Write the expression of total heat transfer to water all along the pipe.

Q: When fitting a freshly ground valve into a freshly ground seat: Technician A says that the seat shou...

A: The reconditioning of the valve seats is done to remove cracks, pitting and grooves from its surface...

Q: Please find the question attached.

A: Given data as per question Y = 3.56 x1/4 calculations;

Q: 3-123: A round shaft has two grooves in which rings are placed to retain a gear in position, as show...

A: Given data as per question When load is applied, maximum stress occurred at minimum cross section ar...

Q: (Mechanics and Materials Class) Problem 7: Find the reactions at the supports, and find the shear fo...

A: Take RA and RF as the reaction forces on the left and right support of the beam respectively. Shear ...