Transmission and Distribution of Electric Power Answer the Following Question Please: Q) Three-phase transmission line, 60HZ, have: (50 MW, 0.866 lagging p.f. and 132 kv in receiving end. If the line have (Z = 100 <80 Ohm / phase and Y = 0.0012 <90 S). Calculate: Vs, Is, Vreg, and power factor in sending end. Also, find the transmission efficiency? For the following transmission models: 1- Short transmission line model. 2- Medium transmission line (pi) model.

Transmission and Distribution of Electric Power Answer the Following Question Please: Q) Three-phase transmission line, 60HZ, have: (50 MW, 0.866 lagging p.f. and 132 kv in receiving end. If the line have (Z = 100 <80 Ohm / phase and Y = 0.0012 <90 S). Calculate: Vs, Is, Vreg, and power factor in sending end. Also, find the transmission efficiency? For the following transmission models: 1- Short transmission line model. 2- Medium transmission line (pi) model.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.26P: A small manufacturing plant is located 2 km down a transmission line, which has a series reactance...

See similar textbooks

Similar questions

A 40-km, 220-kV, 60-Hz, three-phase overhead transmission line has a per-phase resistance of 0.15/km, a per-phase inductance of 1.3263 mH/km, and negligible shunt capacitance. Using the short line model, find the sending-end voltage, voltage regulation, sending-end power, and transmission line efficiency when the line is supplying a three-phase load of (a) 381 MVA at 0.8 power factor lagging and at 220 kV and (b) 381 MVA at 0.8 power factor leading and at 220 kV.
Consider a long radial line terminated in its characteristic impedance Zc. Determine the following: (a) V1/I1, known as the driving point impedance. (b) | V2 |/V1|, known as the voltage gain, in terms of al. (c) | I2 |/| I1 |, known as the current gain, in terms of al. (d) The complex power gain, S21/S12, in terms of al. (e) The real power efficiency, (P21/P12)=, terms of al. Note: 1 refers to sending end and 2 refers to receiving end. (S21) is the complex power received at 2; S12 is sent from 1.
Calculate the capacitance-to-neutral in F/m and the admittance-to-neutral in S/km for the three-phase line in Problem 4.18. Also calculate the line-charging current in kA/phase if the line is 110 km in length and is operated at 230 kV. Neglect the effect of the earth plane.
1/In the Transmission Line Simulator, the Transmission Line is connected in Nominal-Pi Circuit. Select one: True False
a) Find the IBC load currentb) Give the VCA line voltagec) Calculate the total complex power on the transmission line.
For a given short transmission line of impedance R+jX ohms/phase, the sendingend and receiving end voltages Vs and Vr are fixed. Derive the expression for themaximum power that can be transmitted over the line.
A short 3 phase transmission line, connected to a 33kV, 50 Hz generating station at the sending end is required to supply a load of 10Megawatts at 0.8 power factor lagging, 30kV at the receiving end. If the minimum transmission line efficiency is to be limited to 96%, estimate the per phase values of resistance and inductance of the line.
A dc transmission facility is modeled by the approximate series circuit shown below. If the load voltage is known to be Vload= 458.3 kilovolt (kV) what is the power loss in the line in megawatt (MW)?
transmission line with an impedance of 35 Ω is connected to a load of impedance of 300 Ω, then the value of VSWR assuming that the line impedance is decreased by 30 % and load impedance is increased by 40%.
A 46-kv 0.8-lagging power factor load is connected to the end of a short transmission line where the voltage is 230. If the line resistance and reactance are 0.06 and 0.08 ohm, respectively, calculate the voltage at the sending end.
Estimate the distance over which a load of 15000 kW at 0·85 p.f. can be delivered by a 3-phase transmission line having conductors of steel-cored aluminum each of resistance 0·905 Ω/phase per kilometer. The voltage at the receiving end is to be 132 kV and the loss in transmission is to be 7·5% of the load.
Given a telephone transmission line of 100 mile long has Z,=685-j92Q, 0a=0.00497 neper/mile and f=0.0352 rad/mile work at 1000Hz. If Z=2000Q and Eg=10Vrms with Z:=700Q, find the sending end impedance, voltage, current, and power.