True/False Hazard asssessment process is process to ensure safety of the plant.

Q: Relative humidity of the air

A: Given; A room contains 35kg of dry air; ma=35 kgwater vapour is 0.5 kg; mv=0.5 kgPtotal=100…

Q: What is the service life

A: Introduction: While purchasing any equipment for industrial/household purpose, one of the most…

Q: Controlling the Radiation of Heat.

A: Radiation of heat is defined as a loss through which heat from the system is radiated outside the…

Q: Air leakage does not affect the boiler plant efficiency, us this statement true or false

A: Required :- To state whether the statement "Air leakage does not affect the boiler plant efficiency"…

Q: True or False: The probable origin of a fire is most likelyclosest to the lowest point that shows…

A: After the fire has been extinguished  the steps of the authority must be to investigate the fire…

Q: Backgrour grid Exit jet

A:

Q: Draw the Ts diagram of the whole process

A:

Q: Taw un a heat balance sheet for t

A:

Q: Water pump at home is not working properly. Do fault tree analysis

A: Pump: Pump is a device that is used to increase the pressure of the fluid. In various applications,…

Q: 9. The ability to do work is referred to as __________ 10.Plant or animal materials which can be…

A: Work is equal to force into displacement.

Q: s stoves, the recommended lubricant to be used in gas flow control valves is: No lubrication needed…

A: For gas stove, the lubricant is used in gas control valve as  Molybdenum disulfide or graphite…

Q: means the repair work done to keep the system in good working condition.

A: we will discuss an activity/ process that is involved with work  done to keep the system in good…

Q: Types of engine oil

A: There are mainly three types of engine oil  1. Full Synthetic engine oil 2. Mineral engine oil  3.…

Q: Identify an enginecring problem and apply principles of engineering economy to find the solution.

A: Principle of Engineering economy: Engineering economy is the science of applying economic criteria…

Q: rainsient Cooling -Many years ago, the engineering building air compressor dryer failed and visible…

A: In less difficult terms, air temperature, humidity, compressor measure, and required weight will…

Q: The agent acting in between hot body and cold body is a Air conditioner Select one:

A: It is asked if Air conditioner is the agenet that acts between hot body and cold body.

Q: above boiler. Discuss briefly TWO sources of pollution and indicate FOR EACH source ONE required…

A: Emanations from ICI boilers are a work of the sort and amount of essential fuel burned within the…

Q: processes ems that do plve heat ed; (a) mal ses (b) rium ses (c) al ses (d) tic

A:

Q: Make decisions concerning needs and types of ventilation for acceptable indoor air quality?

A: The types of ventilation is given.

Q: *with heat Source energy balance

A: When constructing a heat exchanger, an energy balance calculation is frequently used to calculate…

Q: GIVE THE JOB OR OPERATION WHERE HIGH AIR HUMIDITY IS PRESENT

A: Humidity is the concentration of water vapor in the air. water vapor in the gaseous form is…

Q: Benifits of Building Energy Management System (BEMS)

A: Option C is correct i.e: all the options are correct

Q: Briefly state the desirable properties of a refrigerant?

A:

Q: Maintenance will extend the of the equipment.

A: 1. Maintenance is generally done for basically two requirements One is the regular maintenance to…

Q: The optimum effective temperature for human comfort is ?

A: For a human being,

Q: Example procedure of Level, Flow, Pressure and Temperature control system

A: Introduction: A control system is a system of interest for a specific analysis in space. The control…

Q: A ground source heat pump system uses wells as its heat source. Four wellsare needed for the system.…

A:

Q: a generic 2.5MW

A:

Q: 2. Because parts washers use cleaning solutions that eventually become spent, they must be disposed…

A: Part washers are generally used to clean the  parts or components. part washers create hazardous…

Q: variable that commonly used in oil and gas industries.

A: (A) Number of progressive stages (activities including an adjustment of the material being dealt…

Q: What is energy management? Elaborate energy audit process/steps

A: ENERGY MANAGEMENT  .The method of controlling and maximizing energy use to conserve the use of…

Q: Slow cooling of metal parts creates hard structure in the metal. Select one: True False

A: The higher the cooling rate of the quenching, the smaller the size of the grain size. Hence, it will…

Q: 1. Describe the operation of a compressor.

A: A compressor is a mechanical device that increases the pressure  of a gas  by reducing its volume.…

Q: The state of water is

A: Given data. Rigid container having, Volume,v= 0.5 m3 Mass,m= 1 kg of waterTemperature,T=…

Q: Mechanical working of metal is another name for O a. Casting process O b. Machining process O c.…

A: Mechanical working is forming process .. there are two types of working cold and hot working.

Q: what is Cp of the air Properties and Compressor

A:

Q: Draw the system of Boiler, put a label.

A:

Q: List tools which can be used to for minutes ahead forecasting?

A: Solution:

Q: Question:  What is energy management? Elaborate energy audit process/steps. Note: This Question is…

A: Required :-  Energy management Energy audit process/steps

Q: Hagan system in a thermal power plant is used for..? Option 1: Automatic combustion control Option…

A: Thermal power plant: The power plant which convert the heat energy (by burning of fuels) convert…

Q: 4. A 4 m' storage tam pressure is 20 bar. A steam in the tank? Hov

A: The specific volume of the steam at the given pressure and temperature is v˙=0.1115 m3/kg Initial…

Q: available affordable safe custormer satisfaction

A: Explanation: 1) Power plant are mainly intended to produce power.  2) So in the process of producing…

Q: Octane number is the measure of a fuel's ability to resist knocking. The higher the octane number,…

A: Explaine octane no

Q: In Basic Occupational Safety and Helth    Describe the Chain Reaction that is triggered when fire…

A: Given question: Describe the Chain Reaction that is triggered when fire has started.

Q: When the plant rotating equipment is installed what are possible environment problems will be faced…

A:

Q: Discuss the line maintenance, repairs and alterations.

A: Aircraft maintenance is a highly regulated sector that requires licenced Maintenance, Repair, and…

Q: List some of the good operating pract for boilers. Describe some of the emergency operation…

A: Given Data : Boilers Emergency operation procedures

Q: succesive customer arrival in between 1 and 3 minutes

A: Given : Arrival rate,          λ=30/ hr      so,            λ=12min.Therefore,…

General safety guidelines

Safety guidelines are the set of rules and codes that must be followed in the workplace for the occupational safety of workers, the machines, and the equipment that are present inside the workshop premise. There are many unsafe conditions and hazardous materials inside the workshop that makes prey for certain risk factors associated with health conditions. Extreme safety precautions must be taken inside the work area just like the precautions and practices that are been followed for Corona Virus Disease 2019 (COVID-19). People can also educate themselves by joining various health programs and camps. These will provide them with the necessary skills and knowledge about safety awareness. Occupational Safety and Health Administration (OSHA) thrives to create a safe and healthy environment for the workers working in the industries and provides them with proper education and training.