Two bolts are used to form a joint connecting rectangular bars in tension as shown. If the bolts have a diameter of 11.2mm and the load is P = 95KN, determine the average shear stress (in MPa) on the bolt surfaces that are subjected to direct shear. Note: Do NOT include units in your answer P/2 P/2 w/2 P Answer:

Two bolts are used to form a joint connecting rectangular bars in tension as shown. If the bolts have a diameter of 11.2mm and the load is P = 95KN, determine the average shear stress (in MPa) on the bolt surfaces that are subjected to direct shear. Note: Do NOT include units in your answer P/2 P/2 w/2 P Answer:

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.9.3P: A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is...

See similar textbooks

Similar questions

A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
A flexible connection consisting of rubber plates (thickness t = 9 mm) attached to the steel plates is shown in the figure. The plates are 160mm long and 80mm wide. (a) Determine the force that can be applied to the arrangement, if it is not to exceed a shear stress of 350kPa
A torque of 2 kip # in. is applied to the tube. If the wall thickness is 0.1 in., determine the average shear stress in the tube.
The five-bolt connection must support an applied load of P = 3500 lb. If the average shear stress in the bolts must be limited to 29 ksi, determine the minimum bolt diameter that may be used for this connection.
For the connection shown, the bolt diameter is d = 30 mm. The average shear stress in the bolts must be limited to 160 MPa. Determine the maximum load P that may be applied to the connection based on the shear strength of the bolts.
The beam is supported by a pin at B and a short link AC. All pins are in double shear as shown in and each has a diameter of 40 mm assume P1=98 kN and P2= 49 kN. A) Determine the average shear stress developed in the pin at A B) Determine the average shear stress developed in the pin at B C) Determine the average shear stress developed in the pin at C
The bar has a cross-sectional area A and is subjected to the axial load P. Determine the average normal and average shear stresses acting over the shaded section, which is oriented at u from the horizontal. Plot the variation of these stresses as a function of u 10 … u … 90°2.
The joint is fastened together using three bolts. Determine the required diameter of the bolts if the failure shear stress for the bolts is 7., = 350 MPa. Use a factor of safety for shear of F.S. = 3. Also determine the normal stress for plate, the thickness and widih of a plate are 20mm and 200mm respectively. 40KN | side view 40KN top view
Two bolts are used to lap joints two steel plates. The tensile force on the plate is 40 kN. Determine the required diameter of the bolts if the failure shear stress of the bolts is 350 MPa. Use a factor of safety for shear equal to 2.5.
A typical stainless steel cylindrical vessel is shown. The inside diameter of the tank is 48.0 in. and the wall thickness is 0.75 in. The tank is pressurized to 1.40 ksi. Determine the absolute maximum shear stress on the inner surface of the cylinder wall.
The pipe assembly shown is subjected to a force F = 400 N. The pipe has an inner diameter of 20 mm and an outer diameter of 30 mm. It is made of steel with Sy = 250 MPa. Determine the safety factor at point A using the maximum shear stress theory. Select one: a. NA = 1.843 b. NA = 3.224 c. NA = 2.580 d. NA = 4.299
Assuming that the load P = 120 KN is carried equally by the four rivets in the figure showing the double lap connection, determine the following: (a) the shear stress in the rivets if the diameter of the rivet is 16 mm and (b) the thickness of the inner steel plate if the bearing stress is132.63 MPa.