Two solid steel shafts are fitted with flanges that are then connected by bolts as shown. The bolts are slightly undersized and permit a 1.5° rotation of one flange with respect to the other before the flanges begin to rotate as a single unit. Knowing that G = 77 GPa, determine the maximum shearing stress in each shaft when a torque of T of magnitude 570 N m is applied to the flange indicated. The torque T is applied to flange C. %3D

Two solid steel shafts are fitted with flanges that are then connected by bolts as shown. The bolts are slightly undersized and permit a 1.5° rotation of one flange with respect to the other before the flanges begin to rotate as a single unit. Knowing that G = 77 GPa, determine the maximum shearing stress in each shaft when a torque of T of magnitude 570 N m is applied to the flange indicated. The torque T is applied to flange C. %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Under normal operating conditions, a motor exerts a torque of magnitude TF at F. The shafts are made of a steel for which the allowable shearing stress is 12 ksi and have diameters dCDE = 0.900 in. and dFGH = 0.800 in. Knowing that rD = 6.5 in. and rG = 4.4 in., determine the largest allowable value of TF.
Knowing that the internal diameter of the hollow shaft shown is d = 0.9 in., determine the maximum shearing stress caused by a torque of magnitude T = 9 kip·in.
The design specifications of a 1.2-m-long solid transmission shaft require that the angle of twist of the shaft not exceed 4° when a torque of 750 N·m is applied. Determine the required diameter of the shaft, knowing that the shaft is made of a steel with an allowable shearing stress of 90 MPa and a modulus of rigidity of 77.2 GPa.
A torque of magnitude T= 100 N·m is applied to shaft AB of the gear train shown. Knowing that the diameters of the three solid shafts are, respectively, dAB= 21 mm, dCD= 30 mm, and dEF= 40 mm, determine the maximum shearing stress in (a) shaft AB, (b) shaft CD, (c) shaft EF.
A 88-N·m torque is applied to a hollow shaft having the cross section shown. Neglecting the effect of stress concentrations, determine the shearing stress at points a and b. The shearing stress at point a is MPa. The shearing stress at point b is MPa.
Shaft CD is made from a 66-mm-diameter rod and is connected to the 48-mm-diameter shaft AB as shown. Considering only stresses due to twisting and knowing that the allowable shearing stress is 60 MPa for each shaft, determine the largest torque T that can be applied.
Two solid steel shafts are connected by the gears shown. Knowing that for each shaft G= 11.2 * 106 psi and the allowable shearing stress is 8 ksi, determine (a) the largest torque T0 that may be applied to end A of shaft AB and (b) the corresponding angle through which end A of shaft AB rotates.
The torques shown are exerted on pulleys A and B. Consider TA = 270 N·m and TB = 400 N·m. Knowing that both shafts are solid, determine the maximum shearing stress in shaft BC. The maximum shearing stress in shaft BC is ____ MPa.
The preliminary design of a motor-to-generator connection calls for the use of a large hollow shaft with inner and outer diameters of 4 in. and 6 in., respectively. Knowing that the allowable shearing stress is 12 ksi, determine the maximum torque that can be transmitted by (a) the shaft as designed, (b) a solid shaft of the same weight, and (c) a hollow shaft of the same weight and an 8-in. outer diameter.
Shaft AB is made of a steel with an allowable shearing stress of 90 MPa andshaft BC is made of an aluminum with allowable shearing stress of 60 MPa.Knowing that the diameter of shaft BC is 50 mm and neglecting the effect ofstress concentrations, determine (a) the largest torque T that can be appliedat A if the allowable stress is not to exceeded in the shaft BC, (b) thecorresponding required diameter of shaft AB.
A torque of magnitude T= 120 N·m is applied to shaft AB of the gear train shown. Knowing that the allowable shearing stress is 75 MPa in each of the three solid shafts, determine the required diameter of (a) shaft AB, (b) shaft CD, (c) shaft EF.
The solid shaft shown is formed of a brass for which the allowable shearing stress is 55 MPa. Neglecting the effect of stress concentrations, determine the smallest diameters dAB and dBC for which the allowable shearing stress is not exceeded. Take TC = 300 N·m.