Use the following figure to answer the following question: In this circuit (inverter), the half-wave, controlled rectifier is connected to a 200 V source (VRMS(p) = 200 V). The PWM controller works with a sampling (switching) frequency equal to 1250 Hz to generate a 120 V(RMS) and 60 Hz output voltage. 1 s1 S2 V1 C1 100uF + Vout- 200 V 35 Hz S3 S4 PWM Controller Assume firing angle equal to 10 deg. and find the on-time duration (TOn) for the PWM waveform when the output sinusoidal waveform has an instantaneous amplitude equal to 150 V.

Use the following figure to answer the following question: In this circuit (inverter), the half-wave, controlled rectifier is connected to a 200 V source (VRMS(p) = 200 V). The PWM controller works with a sampling (switching) frequency equal to 1250 Hz to generate a 120 V(RMS) and 60 Hz output voltage. 1 s1 S2 V1 C1 100uF + Vout- 200 V 35 Hz S3 S4 PWM Controller Assume firing angle equal to 10 deg. and find the on-time duration (TOn) for the PWM waveform when the output sinusoidal waveform has an instantaneous amplitude equal to 150 V.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Using the sine PWM method with the full bridge inverter below, it is desired to generate a voltage of 50Hz on the series RL load. A voltage of 120 V DC is applied to the input of the inverter circuit. Amplitude modulation rate ma = 0.9 and frequency modulation rate mj = 19. The resistance of the series RL load is 15 ohms and the coil inductance is 40 mH. What is the total harmonic distortion value (THD) of the power drawn by the load resistor and the load current?
1. A single phase half-bridge inverter, connected to 230V dc source, feeds a resistive load of 10Ω. Determine (a) fundamental rms output voltage (b) total output power and fundamental frequency power (c) average and peak currents of switches (d) input pf. 2. Discuss 1200 mode of conduction for a 3ph-phase VSI. Also, derive the expression for the outputvoltage and draw waveforms for phase voltages, line voltages and voltage across one switch.
A DC link inverter has an AC rms line input of 600 V, 50Hz. The inverter load is a balanced star connection of 195Ω resistors.Determine load current and power for a converter firing angle delay ofa) Determine load current, voltage and power for a converter firing angle delay of 12.5 degrees.b) Determine load current, voltage and power for a converter firing angle delay of 62 degrees.
Find the RMS voltage expression of output phase voltage of a balanced three-phase square wave inverter need it asap
A HVDC link is operating with 175 KV AC line voltage at the rectifier. When the DC current is 1100 Amps, the rectifier delay angle is 100 and inverter extinction angle is 200. The resistance of the line is 23 ohms and the commutating reactances of the rectifier and inverter are 22 ohms and 21 ohms. Calculate the DC voltages at the rectifier and inverter terminals and the AC line voltage at the inverter.
A single phase half bridge inverter has input voltage of 48 V DC. Inverter is feeding a load of 2.4 ohm. The rms output voltage at fundamental frequency is ?
In a lowering converter, the input voltage is Vs = 20V, the output voltage is Va = 10V, and the average value of the load current is Ia = 1.0A. The switching frequency is set to 50 kHz. If the inductance value in the inverter is L = 100 μH and the capacity value is C = 200 µF (a) the duty ratio of the switch D (b) the ripple / ripple (ΔI) value of the coil current (c) the ripple / ripple (Vc) of the output voltage and (d) the switching Calculate the maximum current passing through the element. Draw the waveforms of coil current (iL), switch current (isw) and diode current (i1) in the area below for a switching period according to these values.
A single-phase full bridge inverter is operated from a 48V battery and issupplying power to a resistive load of 10 Ω. Determine:(i) The fundamental output voltage and first five harmonics.(ii) RMS value by direct integration method and harmonic summationmethod.(iii) Output rms power and output fundamental power.
Single-phase full-bridge inverter is connected between a 200 V d.c. source and a series connected R-L load with R = 20Ω and L = 50 mH. The inverter frequency is 50 Hz. Determine the values of the rms load current, the load power and the total harmonic distortion factor, up to the 9th harmonic.
Q1) The square-wave inverter has a dc input of 150 V and supplies a series RL load with R-20 Ω and L = 40 mH.(a) Determine an expression for steady state load current.(b) Sketch the load current and indicate the time intervals when each switch component (Q1, D1:.. Q4, D4) is conducting.(c) Determine the peak current in each switch component.(d) What is the maximum voltage across each switch?
Design a series inverter circuit for operation in the frequency range 50Hz to 90 Hz. The load resistance may vary from 20 Ohm to 80 Ohm. :Thepeak load current is limited to 4 A and the supply voltage is 120 V
A resistive load of 30Ω is connected to an IGBT based Single-Phase Half-Bridge Inverter.The DC source voltage Vs=120V. EVALUATE THE Output voltage (rms value) and peak voltage across the device at OFF state;