Answered: Using the 8085 assembly language, write…

Using the 8085 assembly language, write a snippet program to exchange thecontents of BC register pair with DE register pair without using MOV instructions.

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter4: Processor Technology And Architecture

Section: Chapter Questions

Problem 22VE: Two 1-bit values generate a 1 result value when a(n) _____ instruction is executed. All other input...

See similar textbooks

Related questions

Q: For a MIPS lw instruction, ALU needs to perform _______. a) addition b) subtraction c)…

A: a) addition Option a) is the correct option.

Q: Write an 8085 assembly program to load register A with 50H, and register B with 20H, exchange (swap)…

A: Write an 8085 assembly program to load register A with 50H, and register B with 20H, exchange (swap)…

Q: Q2\ Write an assembly language code to copy the content of (AX register) to the (BX register), and…

A: below is the assembly language code:

Q: In MASM use the XCHG instruction no more than three times, reorder the values in four 8-bit…

A: XCHG: Exchanges the contents of the destination and source operands. This is an instruction to…

Q: Computer Science Suppose, a control register of 8155 PPI has an address of 1Fh. If following…

A: Answer:

Q: he automation of a light is designed by interfacing it with the output port having the address 01H…

A: he automation of a light is designed by interfacing it with the output port having the address…

Q: use assembly language 8086 to Write equivalent code of (( CBW )) instruction.

A: Lets see the solution.

Q: By using stack instructions (push & pop), Write an assembly 8086 program Load the content of BX into…

A: It is defined as a low-level language which is developed by using mnemonics. The microcontroller or…

Q: Assembly instructions

A: Given :- In the above question, a statement is mention in the above given question Need to write…

Q: Write a single SHLD instruction that shifts the highest bit of the AX register into the lowestbit…

A: The following instruction will shift AX register's highest bit to DX register's lowest bit and will…

Q: JNC label instruction belongs to O a. Register Indirect addressing O b. Direct addressing Oc…

A: Required:

Q: Convert the following MIPS assembly language instruction to binary: add $15, $s1, $s2

A: Hii, the answer is given below...

Q: ts by 4 using shift instruction 2) Move 1234H into DS register.

A: Write the appropriate 8086 instructions to perform the following operations:1) Multiply AL register…

Q: An LC-3 assembly language program contains the instructions z LD R4, Y LD RS, Z The symbol table…

A: LC-3 Assembly instructions: Z LD R4, Y Y LD R5, Z Symbol table entry for Z is x300A.

Q: Q 4. (05%) Using the 8085 assembly language, write a snippet program to exchange the contents of BC…

Q: Create a single SHLD instruction that moves the AX register's highest bit to the DX register's…

A: Introduction: Create a single SHLD instruction that moves the AX register's highest bit to the DX…

Q: Based on the diagram below, what is the result for register AX after executing the mnemonic…

A: Below i have answered:

Q: # Write and execute assembly programs that give register AX = 5 , BX = 8, CX = 9.Then swap the value…

A: Not CX Cmp CX,DX JL jump1 Mov BX,1 Jmp skip1 Jump1: Mov ax,10 Skip1: Ret Not CX 0 0 - 6 10 Not…

Q: The CMP R/M is one of the 8085 instruction sets which compares register or memory content with…

A: X(Not used) - It is not used bit irrespective of the operation. CMP instruction is the compare…

Q: Write a single MIPS instruction to initialize register $s1 with zero, without using $0 register.

A: MIPS is a low level instruction set. It is a reduced instruction set computer (RISC) type…

Q: To write a (Register Indirect Addressing Mode) which instruction is correct: MOV AX,DS:[SI] MOV…

A: Let's answer both questions: Q1. To write a ( Register Indirect Addressing Mode ) the correct…

Q: Write a single instruction using 16-bit operands that clears the high 8 bits of AX and doesnot…

A: Instruction An instruction is a single operation of a processor. It is defined by the processor…

Q: Write a program to solve this equation 2+3-4*2 by using registers in MIPS Assembly language.

A: evulate(): push rbp mov rbp, rsp mov DWORD PTR [rbp-4], -3…

Q: About a MIPS instruction Ox08000001 at address Ox0000030 being executed, select all the correct…

A: Given mips instruction as hex value, as binary Binary: 00001000000000000000000000000001 Hex:…

Q: Write down the MIPS instructions that extract bits 16 down to 10 (including bit 16 and bit 10) from…

A: Given: Write down the MIPS instructions that extract bits 16 down to 10 (including bit 16 and bit…

Q: (b). Write an assembly language program in 8085 microprocessor to exchange content of HL register…

A: Example – Assumption – Content is already present in HL and DE register. Algorithm –…

Q: Write the x86 assembler instruction to perform the following: for(i=x; i>0; --i) { if (y ==…

A: The program given is:- for(i=x; i>0; --i) { if (y == 1) c= a+2; else…

Q: Write an 8085 assembly language program to decrement the contents of the register pair ) and copy…

A: Given that Write an 8085 assembly language program to decrement the contents of the register pair )…

Q: Based on operations illustrated in Section 2, write a program to evaluate the arithmetic expression…

A: Instruction formats in CA(Computer Architecture): An instruction in computer comprises of groups…

Q: siven that the program counter register (PC) currently holds the pattern ×2000000C, and that the…

A: a. What is the instruction type? --> I-type explain : The defining characteristic of the I-type…

Q: Write a single SHLD instruction that moves the highest bit of the AX register to the lowest bit…

A: Given that: Write a single SHLD instruction that moves the highest bit of the AX register to the…

Q: Write a machine code of given assembly instructions Where the OPCODE of MOV is 010010 a. MOV ARR,…

A: The Machine code for the instruction: Mov DX, [BX+SI] . Consider the Opcode for a Mov operation to…

Q: Using a simulator, write, assemble and run 8051 program to multiply the unsigned numbers stored in…

A: The code will work for any 1-byte value stored in R1 and R2. For the simulation, I used values of R1…

Q: Develop an assembly language program for 8085 microprocessor to count continuously in hexadecimal…

A: Program Plan:- The counter will be set by using register and loading it with starting number and…

Q: Q3: A- Write an assembly language program to evaluate 2(AX)+4(BX) by using shift and arithmetic…

A: Given: 2(AX)+4(BX) using shift and arithmetic instruction

Q: Identify the Offset Register/s needed by the Segment Register to have the Physical Address. Stack…

A: Stack Segment: The stack segment register (SS) is usually used to store information about the memory…

Q: a) For the following fragment of 8086 program, show the content of register AX after each…

A: contentent of AX register is AX=AH+AL

Q: Write a short sequence of instructions in assembly that divides the number in BL by the number in CL…

A: SOLUTION 1: MOV AL,BL MOV AH,0 DIV CL MOV BH 4 MUL BH

Q: Suppose, present content of flag register is 058FH. Find the content of AX and Flag register after…

A: The below table explains each instruction of the program in detail. INSTRUCTION TRANSLATION MOV…

Q: Write an 8085 assembly program to load register B, C, D, E with data 1, 2, 3, 4 respectively; add…

A: initially we take address for load data example Address Data 2000 1 2001…

Q: What is the value for the 32-bit register EAX after executing the mnemonic opcode/operand…

A: What is the value for the 32-bit register EAX after executing the mnemonic opcode/operand…

Q: Write a single MIPS instruction to invert all the bits in the register $s0 and write the result of…

A: This can be done with a XOR. Let us assume we are using 32-bit and thus it is easy to translate this…

Q: The program then computes the sum of the three values,

A: Here is the assembly program to compute the sum of theree values:

Q: Write a short sequence of instructions that subtracts the numbers in DI,SI and BP from the AX…

Q: What is the 8085 Assembly Language Instruction That do the follwing Loads 16-bit data in the…

A: Note: The register pair name and the data are not mentioned in the question. Suppose the register…

Q: A- Write an assembly language program to evaluate 2(AX)+4(BX) by using shift and arithmeti…

A: Assembly language is a low-level programming language for a computer or other programmable device…

Q: Explain the operation of the each of the following instructions of 8051 microcontroller. (i) MOV…

A: i) The MOV instruction moves data bytes between the two specified operands. The byte specified by…

Concept explainers

Computer Fundamentals

The computer is termed computation. For calculating or computing something the device that has been used is known as the computer. Or we can say that for performing a fast arithmetic operation the device that has been used is a computer. Storing, processing, and retrieving are the main features of a computer. 

Question

Using the 8085 assembly language, write a snippet program to exchange the
contents of BC register pair with DE register pair without using MOV instructions.

Process by which instructions are given to a computer, software program, or application using code.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

Two 1-bit values generate a 1 result value when a(n) _____ instruction is executed. All other input pairs generate a 0 result value.
A(n) ____________________ instruction copies data from one memory location to another.
Write an 8085 assembly language program to decrement the contents of the register pair ) and copy the result into another register pair . If the ? contents of the (BC; BC = EFCDH
Write a short sequence of instructions in assembly that divides the number in BL by the number in CL and then multiplies the result by 2. The final answer must be a 16-bits number stored in the DX register.
In Assembly Write a single instruction using 16-bit operands that clears the high 8 bits of AX and does not change the low 8 bits.
Identify the addressing modes used for the source and the destination operands in the instructions thatfollow :(a) MOV AL, BL(b) MOV AX, 0FFH(c) MOV [DI], AX(d) MOV DI, [SI](e) MOV [BX]+0400H, CX(f) MOV [DI]+0400H, AH(g) MOV [BX][DI]+0400H, AL
Using the XCHG instruction no more than three times, reorder the values in four 8-bit registers from the order A,B,C,D to B,C,D,A.
j 2 : writw thw follwing perogram with assembly 8051 Write a program that does: Start counting using 13-bit counter 1 (internal initialization).When carry bit is logic 1, store the current count value in the DPTR register. Note: The solution will assume no overflow.
What is the difference between a counter and a delay? Using a simple code example, ILLUSTRATE how an 8085 microprocessor can be used to implement counters and delays. Note: you can read or write to an I/O Interface via IN & OUT instructions in 8085
Write a single instruction using 16-bit operands that clears the high 8 bits of AX and doesnot change the low 8 bits.
Explain the operation of the each of the following instructions of 8051 microcontroller. (i) MOV R1,#35H (ii) XCHD A, @R1 (iii) DEC 15H (iv) SWAP A (v) SETB 00H (vi) CLR C
(a) Write a commented assembly language program along with its equivalent Hex codes in order to add the two hexadecimal numbers i.e. and stored at the memory locations and respectively, and store the sum in register C. Then, the sum is subtracted from and the result is displayed at the output port .