ILIARARFIFnm+EAToutтFieldArmatureUsing the following values: VT = 190 V, IL = 110 A, RA = 0.102, RF = 802, Speed1,250 rpm, and HP=19, determine the output torque in Nm.%3DShow two decimal places. Attach your work to support your answer.(Recall the basic machine equations EA = Kpwm, Tdev = Kpla, and P = Twm: Also,Wm = 2nm/60 and 1 HP = 746 W.)%DYour Answer:Answer

Answered: Image /qna-images/answer/0b5570c7-ca11-4162-a87d-b6f613315134.jpg

Using the following values: VT = 190 V, IĻ = 110 A, RA = 0.102, Rp = 802, Speed = 1,250 rpm, and HP=19, determine the output torque in Nm. %3D %3D Show two decimal places. Attach your work to support your answer. (Recall the basic machine equations EA = Kpwm, Tdev = Kpla, and P = Twm: Also, Wm = 2nm/60 and 1 HP = 746 W.) %3D

Using the following values: VT = 190 V, IĻ = 110 A, RA = 0.102, Rp = 802, Speed = 1,250 rpm, and HP=19, determine the output torque in Nm. %3D %3D Show two decimal places. Attach your work to support your answer. (Recall the basic machine equations EA = Kpwm, Tdev = Kpla, and P = Twm: Also, Wm = 2nm/60 and 1 HP = 746 W.) %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An 8-pole d.c. machine of 1200kW, 600V, 500 rpm and the average value of the reactance voltage per coil is 6.6V. the machine is lap connected of 648 conductor and each coil has two turns, the axial length of the compole 29 cm and the air gap is 0.8 cm, the armature diameter is 0.35m and the ratio (Bmax/Bav) = 1.5. Find the interpole m.m.f.
A 30kW, 150V DC shunt machine has an armature and field resistances of 0.08Ω and 160Ω respectively. Determine the total armature power developed when working as motor taking 30kW input. a) find the total armature power mathmatically
A 50MVA, 11kV salient pole machine having a direct‐axis reactance of 0.8pu and a quadrature‐axis reactance of 0.6pu. The machine is connected to an infinite bus having a voltage of 11kV and supplying 40MW at 0.8 lagging power factor. Determine the power angle, the voltage proportional to field current, the direct axis and the quadrature‐axis components of the voltage and current. The load angle and the excitation voltage at which the maximum power transfer occurs.
A 25kW, 120V separately excited dc machine has an armature resistance of Ra =0.025 ohms. When operated with a constant field current and constant speed of 2500rpm, the open circuit armature voltage is 120V. If the dc machine is connected to a 125V supply, determine (i)Whether the dc machine is operating as a generator or a motor. (ii)The armature current (iii)The supply power (iv)The developed power. (v)The developed torque.
The nominal speed of a construction machine with an operation is 1000 rpm, and when the speed of the construction machine is halved, the power of the electrical machine is halved. What are the characteristics of the electrical machine and the work machine that should be preferred for such a system?
A separately excited motor runs at 1045rpm, with a constant field current, while taking an armature current of 50A at 120V. The armature resistance is 0.1 Ω if the load on the motor changes such that it now takes 95A at 120V, determine the motor speed at this load.
Solve and show illustration A 20-kW 127.4 -V separately excited dc machine is operated at a constant speed of 2702 rpm with a constant field current such that the open-circuit armature voltage is 127.4 V. the armature resistance is 0.03 ohm. Compute the armature current when the terminal voltage is 133. a. 186.67 A b.-186.67 A c. 8680.00 A d. 0 A
a dc shunt generator supplies a load of 10kW at 250V calculate the induced emf,if the armature resistance is o.5ohm and the shunt field resistance is 100ohm
A. Explain briefly the difference between power flow analysis and state estimation. B. Comments on this statement: "PMUS without GPS signal are useless".
Provide state table for following state diagram, and design the mealy machine circuit diagram.
A 32kW, 250V DC shunt machine has an armature and field resistances of 0.05Ω and 120Ω respectively. Determine the total armature power developed when working as generator delivering 32kW output.
Draw the DC Machine and label its parts