Water at a temperature of T∞= 25°C flows over one ofthe surfaces of a steel wall (AISI 1010) whose temperatureis Ts,1= 40°C and thermal conductivity of steel is 671 w/m.k. The wall is 0.35 m thick, and itsother surface temperature is Ts,2= 100°C. For steadystateconditions what is the convection coefficient associatedwith the water flow?

Water at a temperature of T∞= 25°C flows over one ofthe surfaces of a steel wall (AISI 1010) whose temperatureis Ts,1= 40°C and thermal conductivity of steel is 671 w/m.k. The wall is 0.35 m thick, and itsother surface temperature is Ts,2= 100°C. For steadystateconditions what is the convection coefficient associatedwith the water flow?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.62P

See similar textbooks

Similar questions

5.7 The average Reynolds number for air passing in turbulent flow over a 2-m-long, flat plate is . Under these conditions, the average Nusselt number was found to be equal to 4150. Determine the average heat transfer coefficient for an oil having thermal properties similar to those in Appendix 2, Table 18, at at the same Reynolds number and flowing over the same plate.
3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.
1.21 In an experimental set up in a laboratory, a long cylinder with a 5-cm diameter, and an electrical resistance heater inside its entire length is cooled with water flowing crosswise over the cylinder at and a velocity of 0.8 m/s. For these flow conditions, 20 kW/m of power is required to maintain a uniform temperature of at the surface of the cylinder. When water is not available, air at is used with a velocity of 10 m/s to maintain the same surface temperature. However, in this case, the cylinder surface heat dissipation rate is reduced to 400 W/m. Calculate the convection heat transfer coefficients for both water and air, and comment on the reason for the differences in the values.
The heat transfer coefficient for a gas flowing over a thin float plate 3-m long and 0.3-m wide varies with distance from the leading edge according to hc(x)=10x1/4Wm2K If the plate temperature is 170C and the gas temperature is 30C, calculate (a) the average heat transfer coefficient, (b) the rate of heat transfer between the plate and the gas, and (c) the local heat flux 2 m from the leading edge. Problem 1.18
A transformer is to be cooled via forced air convection. To increase the effectiveness of thecooling, Alloy 1095 cast aluminum fins are attached to the top of the transformer overwhich air is blown (negligible thermal contact resistance between the transformer and thefins). The fins are 2 cm thick and 7 cm long and span the entire length of the transformer,and the transformer is 7 cm wide and 10 cm long. Air leaves the cooling fan at 25°C .a) Decide how to model the fins before performing any real analysis. Youare willing to accept some error in your analysis and so you will either model thefins as having adiabatic tips or being infinitely long. You expect the average convectioncoefficient over the heat transfer surfaces for this system to be around 50 W m2– K⁄ .Which tip condition should you use for the fins in your analysis? b) Modeling the transformer as being isothermal, determine the average convectioncoefficient over the heat transfer surfaces. Account for heat transfer from the…
For fluids with small Prandt number the thermal boundary layer development is much ....................than that of the velocity boundary layer (δt ≫ δ), and it is reasonable to assume ....................... velocity (u = u∞) throughout the thermal boundary layer. Please fill the blank
A long thin glass walled, 0.3 cm diameter, mercury thermometer is placed in a stream of air with convection coefficient of 60 W/m2 -K for measuring transient temperature of air. Consider cylindrical thermometer bulb consists of mercury only. For which k = 8.9 W/m.K and α = 0.016 m2 /h. Calculate the time constant and time required for the temperature change to reach half of its initial value.
A thermocouple junction, which may be approximated as a sphere, is to be used for temperature measurement in a gas stream. The convection coefficient between the junction surface and the gas is h=400W/m².K, and the junction thermophysical properties are ĸ= 20W/m.°K, c= 400J/kg.°K and ρ=8500kg/m³. Determine the junction diameter needed for the thermocouple to have a time constant of 1s. If the junction is at 25°C and is placed in a gas stream that is at 200°C, how long will it take for the junction to reach 199°C?
In thermally fully developed flow of a fluid with constant properties, the local convection coefficient is .......................... , ........................ please fill the blank Blank 1( a constant or not a constant) Blank 2 ( dependent on or independent of)
The heat transfer from a 3 m diameter sphere to a 27 deg C air stream over a time interval of one hour is 4000 kJ. Estimate the surface temperature of the sphere if the heat transfer coefficient is 15 W/m^2K.
Air at 24°C is blown over a hot pipe with a surface area of 2.94 m2 to dissipate 924 W of heat energy. What is the minimum convection heat transfer coefficient that will ensure that the temperature of the pipe surface is less than 45°C [round your final answer to two decimal places]?
Topic: Heat transfer Completely solve and box the final answer. A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent? If the average laminar heat transfer coefficient of water is 7740W/m2 degC, what is the overall heat transfer at the laminar section?