Water (cp = 4182 J/Kg.K) at a flow rate of 5000 Kg/hr is heated from 10oC to 35oC in an oil cooler by engine oil (cp = 2072 J/Kg.K) with an inlet temperatureof 85oC and a flow rate of 6000 Kg/hr. Take the overall heat transfer coefficient to be 3500 W/m2.K. What are the areas required for: a. Parallel Flow. b. Counter Flow

Water (cp = 4182 J/Kg.K) at a flow rate of 5000 Kg/hr is heated from 10oC to 35oC in an oil cooler by engine oil (cp = 2072 J/Kg.K) with an inlet temperatureof 85oC and a flow rate of 6000 Kg/hr. Take the overall heat transfer coefficient to be 3500 W/m2.K. What are the areas required for: a. Parallel Flow. b. Counter Flow

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.54P

See similar textbooks

Similar questions

Geothermal heat pumps, or water-source heat pumps, are classified as either _____loop or _____loop systems.
Explain why a waterless, earth-coupled, closed-loop geo-thermal heat pump system is more efficient than a conventional closed-loop geothermal heat pump system.
What is the main difference between a copper and a cupronickel coaxial heat exchanger, and where is each used?
The condenser of a room air conditioner is designedto reject heat at a rate of 15,000 kJ/h from refrigerant-134aas the refrigerant is condensed at a temperature of 408C. Air(cp 5 1005 J/kg?K) flows across the finned condenser coils,entering at 258C and leaving at 358C. If the overall heat transfer coefficient based on the refrigerant side is 150 W/m2?K,determine the heat transfer area on the refrigerant side.
A two pass steam surface condenser is to be designed to condense 10000 kg/hr of steam having an enthalpy of 2240 kj/kg. Condenser pressure is 13.79 kpa. circulating water enters the condenser at 25 C and leaves at 40 C. the outside and inside diameter for a water tube, OD=20 mm, ID = 17 mm and water velocity of 3 m/s. if the overall coefficient of the heat transfer is 14100 kj/hr-m-C of outside tube surface, determine the amount of circulating water in m/hr.
Is a car radiator a heat exchanger? If yes, then which type of heat exchanger is this?
A double pass water-cooled shell-and-tube type condenser has a total number of tubes equal to 42. The tubes are of 14 mm inside diameter, 16 mm outside diameter and 4 m length. The overall heat transfer coefficient is 3510 kJ/hr-m2 -°C. Cooling water enters the condenser at 25°C at a velocity of 1.5 m/s and leaves with a temperature rise of 6.5°C. (a) Calculate the outside heating surface area of the tubes in m2 ; (b) Determine the mass flow rate of water in kg/s and the volumetric flow rate in L/s (using an average density of 996.5 kg/m3 ); (c) Estimate the condensing temperature of the refrigerant; (d) If the ammonia refrigerant enters and leaves the condenser at saturation conditions, compute the mass flow rate of the refrigerant and the condenser pressure in kPa.
A jacketted-agitated vessel, fitted with a turbine agitator, is used for heating a water stream from 10°C to 54°C. The average heat transfer coefficient for water at the vessel’s inner-wall can be estimated from Nu = 0.76Re2/3Pr1/3. Saturated steam at 100°C condenses in the jacket, for which the average heat transfer coefficient in kW/m2·K is ho=5 13.1(Tg - Tw)20.25. The vessel dimensions are Dt = 0.6 m, H = 0.6 m and Da = 0.2 m. The agitator speed is 60 rpm. Calculate the mass rate of water that can be heated in this agitated vessel steadily.
Assess the factors that influence the economics of heat pumps.
The food storage room requires a cooling system with a capacity of 15 tons of refrigeration that operates at an evaporator temperature of -17.5 ° C and a condenser temperature of 38.9 ° C. The refrigerant used is R-134a and the system operates in saturated conditions. a. COP = Answer. b. Refrigerant flow rate = Answerkg / s. c. Heat loss rate in condenser = AnswerkJ / s.
To reach the maximum heat exchange rate, if a fan is applied, should it be upward airflow or downward airflow? Need detail explanation. And what will the efficiency difference between upward and downward airflow.
The radiator in an automobile is a cross-flow heat exchanger (UAs = 10 kW/K) that uses air (cp = 1.00 kJ/kg·K) to cool the engine-coolant fluid (cp = 4.00 kJ/kg·K). The engine fan draws 30°C air through this radiator at a rate of 10 kg/s while the coolant pump circulates the engine coolant at a rate of 5 kg/s. The coolant enters this radiator at 80°C. Under these conditions, the effectiveness of the radiator is 0.4. Determine (a) the outlet temperature of the air and (b) the rate of heat transfer between the two fluids.