Water flow steadily at the rate of 10 gpm through a horizontal tee and discharges to theatmosphere. The pressure at the entrance to the tee is 15 psia. Determine the forceexerted on the tube by the tee.FlowD = 0.75 in.-Q= 10 gpmFlow

Answered: Image /qna-images/answer/391bae1d-a78f-41d5-ba7b-d8a0a9a8caf0.jpg

Answered: Water flow steadily at the rate of 10…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the available suction head of the pump that is taking a gasoline at 204°C at a closed tank with a pressure 585 kPa gauge. the specific gravity of gasoline is 0.78 and it’s vapor pressure is 620 kPa absolute. the loss in suction pipe is 0.60 m and the pump center line is located 3.60 m above the gasoline level A. 8.66m B. 3.67m C. 7.66m D. 4.47m
The diameter of a horizontal pipe which is 300 mm is suddenly enlarged to 600 mm. The rate flow of water through this pipe is 0.4 m3/s. If the intensity of pressure in the smaller pipe is 125 kn/m2, determine:1. Loss of head, due to sudden enlargement, 2. Intensity of pressure in the larger pipe. and 3. Power lost due to enlargement.
Water at 65 degrees Celsius is flowing horizontally at a rate of 84.1 m^3/hr in a pipe. It enters a 150-mm 90 degree elbow and is diverted upwards into a connecting pipe. The diameter of the outlet is 85mm. If the pressure just before the elbow is 95 kPa, determine the magnitude and direction of the force necessary to keep the elbow in place. Assume frictional losses in the elbow are negligible.
A simple pitot tube and a piezometer are installed in a vertical pipe as shown in the figure. If the deflection in the mercury manometer is 0.1 m, then determine the velocity of the water at the center of the pipe. The densities of water and mercury are 1000 kg/m3 and 13600 kg/m3 , respectively.
Oil flows from a tank through 150 m of 150 mm diameter pipe andthen discharges into air as shown. If the head loss from point 1to point 2 is 600 mm, determine the pressure needed at point 1 tocause 17 L/s of oil to flow.
3. What is the volumetric flow rate between two plates if the top plate is pulled, while keeping the bottom plate stationary, and simultaneously imposing pressure p0 on the left endof the channel, and pressure p0 + ∆p (∆p > 0) on the right end of thechannel.
In the test of the reaction turbine, the water flowing over the weir in the tailrace was found to be 39.8 ft3 /s. The leakage into the tailrace was found to be 1ft3 /s. The elevation of the centerline of the shaft above, the surface of tailwater was 12.67ft. The diameter of the turbine intake was 30in and the pressure at this section was measured by a mercury U-tube. The readings in the two sides of the mercury U-Tube were 10.556 ft and 0.900 ft, the zero of the scale being at a level 3.82ft below that of the centerline of the turbine shaft. The generator output was 391.8 kW, friction and windage loss 13.8 kW, iron loss 2.0kW and armature loss of 4.4kW. The specific gravity of the mercury used was 13.57. Calculate the efficiency of the turbine.
O1: A stream of water of diameter d = 0.1 m flows steadily from a tank of diameter D= 1.0 m. Determine The Weight Flowrate, needed from the inflow pipe if the water depth remains constant, 0 — d=010m
A pipe line of length 2000 m is used for power transmission. If 110 kW power is to be transmitted through the pipe in which water having a pressure of 490.5 N/cm2at inlet is flowing. If the pressure drop over the length of pipe is 98.1 N/cm2and ff = 0.0065.Determine:The diameter of the pipe and the volume flow rate; and If a nozzle is introduced at the end of the pipe, what would be its diameter and the power transmitted.
The diameter of a pipe changes from 200mm at a section 5 meters below a datum to 50mm at asection 3 meters above datum. The pressure of water at first section is 500kPa. If the velocity of flowat the first section is 1m/s, determine the intensity of pressure at the second section.
Water is flowing out of the nozzle (2) into atmospheric pressure (101 kPa). What is the horizontal force exerted by the flange to hold the nozzle (2) attached to the pipe (1)? Flow velocity at point (2) is 8 m/s. Water density is 1000 kg/m3.
If a pumped hydro installation can hold 30 million m3 of water, and the water head is 36 m: a)Determine the energy content of the installation. b)If the reservoir normally empties within eight hours and fifty-two minutes and the efficiency of the turbine is 67%, calculate the output power of the installation. Calculate the total pressure that the turbine is experiencing

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Water flow steadily at the rate of 10 gpm through a horizontal tee and discharges to the atmosphere. The pressure at the entrance to the tee is 15 psia. Determine the force exerted on the tube by the tee. Flow