Water flows steadily from a nozzle into a large tank as shown in the figure below. The water then flows from the tank as a jet of diameter d. Determine the value of d if the water level in the tank remains constant. Viscous effects are negligible. d= ft 3 ft 0.093-ft diameter 1 ft 4 ft 0.15-ft diameter

Water flows steadily from a nozzle into a large tank as shown in the figure below. The water then flows from the tank as a jet of diameter d. Determine the value of d if the water level in the tank remains constant. Viscous effects are negligible. d= ft 3 ft 0.093-ft diameter 1 ft 4 ft 0.15-ft diameter

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 24P

See similar textbooks

Similar questions

A 100-ft long dam holds 30 ft of water as shown in the figure. Using the panel equations, determine the hydrostatic force (in kips) acting on the dam. Determine the moment of inertia of the wetted surface of the dam. Your answer should be in ft^4. Determine the eccentricity in feet. At what distance from the bottom of the dam (along the surface of the dam) is the hydrostatic force acting? Your answer should be in feet.
7. Two water tanks are connected to each other through a mercury manometer with inclined tubes, as shown in figure. If the pressure difference between the two tanks is 20 kPa, determine the value of ? in degrees. (2 decimal)
Pitot tube is an instrument that is used to measure flowrate in a pipe. Figure 3 shows water flowing through a pipe with pitot tube attached to a U-tube manometer containing Fluid X. Given the difference in height in the manometer, h, calculate the flowrate through the pipe by showing the application of Bernoulli Equation and Hydrostatic Pressure Equation. Details of the parameters are as follows; Difference in manometer, h = 0.1 m Density of water = 1000 kg/m3 Density of Fluid X = 12000 kg/m3 Diameter of pipe = 0.3m
The system shown in the figure is used to accurately measure the pressure changes when the pressure is increased by ΔP in the water pipe. When Δh = 90 mm, what is the change in the pipe pressure?
fluıd mechanıcs If an oil tank is pulled uphill on a surface that makes an angle of 162 with the horizontal, the oil makes an angle of 160,a) Show the forces acting on the tank on the figure. Write the balance of force.b) Calculate the constant acceleration of the tank being pulled uphill.
As shown in the figure, water flows in the horizontal pipe. The pipe consists of two different sections, 60 mm and 30 mm in diameter, connected by a smooth reduction. The pressure difference between the two sections is measured with a mercury manometer. Friction effects are neglected. The height between the mercury levels in the two sections of the pipe was determined as 1.4m. Find the velocity and mass flow at points 1 and 2. (Density of mercury: 13.6 grams / cm3, Density of water: 1gr / cm3)
Figure 7 shows a pump partially submerged in oil (sg=0.90) and supported by springs. If the total weight of the pump is 14.6 lb and the submerged volume is 40 in3 , calculate the supporting force exerted by the springs.
In a laboratory experiment, a two‐fluid differential manometer is used to measure the pressure drop for a flowing process fluid, a silicone oil that is immiscible with water, as shown in Figure 2. Determine the pressure drop between Points A and B if h1 = 500 mm, h2 = 190 mm, and h3 = 275 mm. The densities of the process fluid and water are 1060 kg/m3 and 1000 kg/m3 respectively.
The figure shows gate AB, 4 meters high, submerged in water. It is inclined 40 degrees with respect to the horizontal. Using the figure shown, determine the distance of CG (center of gravity) to CP (center of pressure) in meters.
Calculate the pressure decrease (in psi) when you climb from an elevation of 660 ft to a mountain top 1640 ft above mean sea level. Assume that the unit weight of air is constant at 0.07967 lb/ft^3.
The figure shows a system where water flows from a tank through a system of pipes of different sizes and elevations. If we assume that there is no energy loss in the system, find: a. The volumetric flow through the pipe in ft3/sb. The pressure at point Bc. The pressure at point Cd. The flow velocity at point F in ft/s
In the figure shown, originally there is a H2=9 cm manometer reading and H1=15 cm. Atmospheric pressure is 101.3 kPa. what is the absolute pressure at A (kPa)? If the absolute pressure at A is doubled, what then would be the manometer reading (cm) ?