What is the conveyor system?

Q: Name at least five different materials that are used in a refrigerator.

A: List of five materials which are used in a refrigerator are:   1. Aluminum  2. A metal sheet  3.…

Q: at type and design of conveyor is used in a

A: A conveyor system is used to move goods, products, materials, etc from one location to another.…

Q: When minimum space is an important requirement, the best type of mechanical connecting device for…

A:

Q: a V-belt depends on the rotational speed of the smaller pulley.

A: In belt drive power transmission depends on following factors 1 linear velocity of velt 2 tension of…

Q: What are the steps to assemble the sheet metal air duct

A:

Q: The material handling equipment that performs overhead movement to move materials is Mobile jib…

A: Mobile Jib Crane :  It is used for transferring materials form one work station to another. It is…

Q: termine the discharg

A: for the other end to open to the atmosphere the net headloss in the pipe should be equal to 3m this…

Q: he material handling equipment that performs overhead movement  to move materials is  Industrial…

A: The material handling equipment that performs overhead movement  to move materials is Pulley drive…

Q: Describe the process of Feedforward Regulation system?

A: In feedforward regulation system controller identifies the errors within the system before output…

Q: when the bottom of a control arm is toward the front of the car and the point turns in to meet the…

A: A trailing arm is a type of independent rear suspension which has the pivot axis precisely…

Q: The more mechanical parts (bearings, gears, belts, etc…) that a machine has, the _______ (more or…

A: as we know that any machine can not be 100 percent efficient. because in nature no any material is…

Q: clearance in the assembly

A: Given; In an interchangeable assembly, shafts of size = 25.00-0.0100-0.040mmsizes of  holes=…

Q: Water is flowing thru the pipe set-up. What can be the v thru pipe 3 ?

A:

Q: Draw the Ts diagram of the whole process

A:

Q: What is control volume?

A: A control volume is a system or space under observation that can exchange mass and energy from the…

Q: This is called the... baggage hold propeller cabin cockpit

A: Baggage hold is the system of aircraft which is used to hold baggage or to store the baggage during…

Q: controls on/off of the motor, when the air compressor tank reaches the specified bar.

A: Compressed and filtered air enters the tank after coming out of the Air compressor

Q: What are the different design parameters for a conveyor

A: Solution:   Conveyors are the means to transport or move the material inside the manufacturing unit.…

Q: ne cost to operate the bulb

A: Given- P= 60W t= 30 days ( power on at 18hr/day) cost= 10cent/kWh Need To calculate the Operating…

Q: FAD Fan -60m- 40 m 40m Figure Q2(b)

A:

Q: What is the purpose of the control cable.

A: Control cables are multi-conductor cables used for automation and instrumentation applications.…

Q: Draw the FBD All distributed loads should be simplified to their equivalent loads Draw the FBD…

A:

Q: The technician............... machine, but ............... no time. He wasn't very busy. to repair…

A: GIven

Q: Bulk loose material is to be emptied from a dump hopper. By pressing a push button P1, the dump…

A:

Q: write discussion about to determination of the capacity of a belt conveyor.

A:

Q: Which of the following is not used in automation of warehouse operations: Select one: Forklifts…

A: Although all the given options can be used in warehouse operations but if we had to select one which…

Q: Q15. Before 1900, vacuum cleaners did not have this component. A. Fan B. Dust compartment С. Host D.…

A: Host:  The working of the host in a vacuum cleaner is to instantly absorb and hold the dissolved…

Q: A cooling fan is connected to the driving motor by a V-belt. How many incheslong is the V-belt?

A: given:

Q: Describe the action of a commutator.

A: Introduction to commutator: commutator is a mechanical part of DC generator or motor which converts…

Q: Which of the following is a gas charged or filled accumulator for the hydraulic system?

A: A gas-charged hydraulic accumulator stores the potential energy of an incompressible fluid using…

Q: How conveyor belt used in water supply system.

A: WATER SUPPLY SYSTEM: A water supply system is one that collects, transports, treats, stores, and…

Q: What is Belt-conveyor system?

A: The belt conveyor system is essential in a material handling industry. It is used to transport bulk…

Q: What is the forklift trucks system?

A: Forklift trucks are the industrial vehicles used for transportation of cargo from one point to…

Q: What is the applications Center of Pressure

A: Center of pressure: It is the point at which the total sum of a pressure field acts on an object…

Q: a). Explain any two advantages and disadvantages of the CNC system.

A: Solution:   Note: Dear Student! As per our guidelines, we are only allowed to answer a single…

Q: Describe the following point-of-operation devices: (a) automatic or semiautomatic feed and ejection…

A:

Q: a DCV, this part moves the spool, it can be a lever or a button a. operator b. springs c. spool…

A: The solution is attached below:

Q: Describe the performance of a flat plate collector with regards to the energy flow.

A: Describe the performance of a flat plate collector with regards to the energy flow.

Q: Blocked suction cylinder unloading is accomplished byA. keeping the suction valve closed.B. closing…

A: given; Blocked suction cylinder unloading is accomplished by

Q: e. Use the data to find the time it takes to fill the supply line.

A: To find Time takes to fill suppy line.

Q: rope is wrapE

A:

Q: ladde

A: ax=14.01m/s^2

Q: f the desc oth of cut rations

A: Chip forming ;

Q: Construct a circuit drawing of a hydraulic dump lift using an open center circuit.

A: To construct an open center circuit of a hydraulic pump

Heat Exchangers

Heat exchangers are the types of equipment that are primarily employed to transfer the thermal energy from one fluid to another, provided that one of the fluids should be at a higher thermal energy content than the other fluid.

Heat Exchanger

The heat exchanger is a combination of two words ''Heat'' and ''Exchanger''. It is a mechanical device that is used to exchange heat energy between two fluids.