What is load-displacement?

Q: What is the NRC for the material?

A: NRC stands for noise reduction coefficient and is the standard rating for how well a material…

Q: What is the Torsion formula?

A: The expression of torsion equation is given by, Here, T is the twisting torque, J is the polar…

Q: PI ミ

A: Answer: The value of spring stiffness k when the deflection of beam is reduced by: (a) 25% of its…

Q: Express the compatibility conditions in terms of the displacements caused by the loading?

A: The compatibility condition is based on the fact that any change in length of the bar must be…

Q: Which material has the greatest UTS?

A: The ultimate tensile stress is the maximum stress in the material corresponding to the strain.

Q: Define the term 'weight'.

A: Weight is the amount of downward force that is applied by gravity to any object in its gravitational…

Q: E material has inner m'K, the temperatu

A:

Q: „Sigma_min= - 500MPA, using mod-Goodman were ap

A: Given Data σmin=500 MPa σmax=-100 MPa Sy=400 MPa Sut=600 MPa Now, σm=σmin+σmax2σm=500-'1002σm=200…

Q: How can the average shear stress be related to the torque?

A: Let us consider an example of a cylinder rotating in viscous fluid with some average shear stress…

Q: Elaborate the following terminology of drawing “SQ THD DIA 21X3 LH ?

A: The term pitch represents the distance between two successive threads and is expressed in mm units…

Q: What is the discontinuity of loading?

A: The load along the length of the structure, say a beam if is consistent then we can say that the…

Q: What is Distortion energy?

A: Distortion in a body is caused when there are shear stress present on the body. Due to these shear…

Q: 30o0mm*300 mmXJ0omm

A: Given data :- 300mm × 300mm × 300mm  Compare L × b × h  Here L= length           b= width…

Q: In mechanical damping method:

A: Given Mechanical damping method To find Appropriate friction process

Q: An eyebolt is lifting a block weighing 360 lbs. The eyebolt is of SAE 1040 material with Su = 67 ksi…

A: Given data Weight of block = 360 lb Sy = 55 ksi = 55000 lb/in2 We have to find the stress area of…

Q: What is referred to as the torsion formula?

A: Let us consider a shaft subject to the torque at the free end and fixed at the other end.

Q: Two springs are at

A: OPTION d)0.20m/s

Q: What is the basic unit for length?

A: Solution Length → The measurement of something from end to end is called length

Q: You are a new employee in a company and they asked you to do a small sketch for Acme thread if p= 10…

A: As per bartleby guidelines only first question has been solved.   The detailed sketch of an acme…

Q: Define the termTruss?

A: The truss is a structure that is used to distribute the load. It is made by combining members into…

Q: What is the Flexure Formula?

A: The stresses in the beam caused by the bending moment is called as flexural or bending stress.

Q: What is compound indexing?

A: Soln:- Compound indexing :- Compound indexing is the operation of obtaining a desired spindle speed…

Q: раper feed for a 12 The photocopier is controlled by two rollers together with approximately 20N.…

A: Given dataForce F = 20NOuter diameter of plastic cylinder  the rollers D = 20mmDiameter of steel…

Q: Name the 2 types of axial loading?

A: Two types of axial loading are tensile and compressive stress. Both kinds of stresses arise within…

Q: What is the name of the circle from which the involute curve is generated? Select one: O a. Base…

A: Involute Curve: The involute curve is a type of mathematical curve. The involute curve is often used…

Q: What is impingement velocity?

A: Flow impingement occurs when the approach channels flow directly into a bank line at large acute…

Q: a) 10mm IG mm IG mm 1050mm IG mm 16mm 250 mm 300 mm

A:

Q: 3. What is the difference between a statically indeterminate member from a statically determinate…

A:

Q: Define the term Shaft Design?

A: Given Shaft design To find Definition

Q: What is Axial Load and explain with example?

A: Axial load is the load which act on the body parallel to the axis or perpendicular to the…

Q: Connecting rod bearings are to be replaced. The journal measures 70.866 mm (2.790 in.)​. The…

A: The Size bearings for above requirements are U/S--0.381 mm (0.015 in) undersize.

Q: Eind feslads osd Tarque Pressre ond N= mim Ponued 1500xpm

A: Mean effective Pressure is the ratio of work done in a cycle to the engine displacement That is,…

Q: When does a free vibration occurs?

A: Condition of free vibration When we apply initial external forces on the body and the body tends to…

Q: 5. How do point loads and uniform distributed load be represented in SFD? a) Horizontal lines and…

A: Option c is correct.

Q: Why scale D is the correct one?

A: Solution:

Q: CII-3. Use reasonable dimensions for this hammer and a loading to show through an analysis why this…

A: The free body diagram of the hammer is given by, Here, F is the human effort.

Q: final thickness that can be produced by this

A: Given data;  Diameter=600 mmCoefficient of friction=0.05 Thickness=2 mmDetermine the minimum…

Q: n rati

A: given: what is poisson ratio?

Q: What is the effective length factor?

A: Effective length is a critical concept in Structural Design which relates to 'the length of a…

Q: 1. IF THE MATERIAL IS MADE FROM BRASS, WHAT IS THE MASS OF THE PART? (UNIT:MMGS)

A: Given: A solid part with dimensions Units=MMGS Material=Brass

Q: Why 100% of the total material is not possible for 100% sampling

A:

Q: 30mm diameter copper (G-4S GPa) shaft is transmitting power at 1000 rpm. The twisting angle should…

A:

Q: er with screw pitch 0.5 mm and divisions on thimble 50, the reading corresponding to 5 divisions on…

A:

Q: Define the term Distributed loads?

A: In structural mechanics, a load that is distributed continuously over a given area or along a…

Q: cycloidal g

A: The cycloidal gear profile, as opposed to the involute gear profile used in most other gears, is a…

Q: What is critical damping?

A: Critical damping is the zero amplitude of a damped oscillator. if the system is critically damped…

Q: ibrication stable? Line of centers Journal Bushing -ho C= radial clearance

A: Solution

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.