What is the difference between tensile strain and volume stress?

Q: Bone or wood which has highest youngs modulus why

A: Bone has the highest young's modulus than that of wood. The value of young's modulus of bone is…

Q: The rapture strength of bone tissue is 100 MPa and Young’s modulus is 10 GPa. Calculate value of…

A:

Q: It is the ratio of the ultimate stress to allowable stress. poisson's ratio. O shear modulus modulus…

A: Poisson's ratio is defined as the ratio of the lateral strain to longitudinal strain, within the…

Q: Determine the strain if a rod is experiencing a stress of 70,000 kPa with a modulus of elasticity of…

A: The modulus of elastivity is the ratio of the stress to the strain.

Q: What is difference between tensile stresses, shear stress and bulk stress?

A:

Q: How should we apply a force on a body to produce shearing stress?

A: Shear stress is the component of stress coplanar with the material cross section. It arises from the…

Q: T the stress experience when deformation is caused by tangential forces to the surface* O Inertia…

A:

Q: The stress - strain relationship become nonlinear in the elastic region. O True O False O O

A:

Q: The ratio of stress to strain in the initial linear is ..? * Young's modulus O viscoelasticity O…

A: In initial linear relationship stress of a material is directly proportional to strain. Stress ∝…

Q: A disk between vertebrae in the spine is subjected to a shearing force of 700 N. Find its shear…

A: Data Given ,  Force ( F ) = 700 N Length of the cylinder ( L ) = 0.700 cm         = 0.700 × 10-2 m…

Q: When a force is applied to an object, the -6 longitudinal stress is equal to it

A:

Q: The two bars shown in the figure are used to support a load P. When unloaded, joint B has…

A: Coordinates of B (0,0) Coordinate of C will be (4,6) Coordinate of A will be (-7,6) We have to find…

Q: A   5.0  inches cube chiffon  cake on  a  table  was  exposed  to  a  shearing  force of 0.20  lb.…

A: Given: The side of the cube is 5.0 in. The shear force is 0.20 lb. The displacement in the upper…

Q: What will be the shear stress value?

A: Apply Hooke law of elasticity

Q: A sculpture weighing 10000N rest on a horizontal surface at the top of a 6.0-m- tall vertical…

A: Given The weight of the sculpture is Ws=10000 N. The height of the vertical pillar is h=6 m. The…

Q: A rectangular beam with cross section 10 cm width and 20 cm depth is loaded as shown in the figure.…

A: MI=σy(Euler Bernoulli's beam bending equation)where M is maximum bending momentI is the moment of…

Q: The stress-strain curve during elastic deformation is non-linear. Is this true or false?

A: When a material is elastically deformed its stress-strain curve is linear in nature till the elastic…

Q: Hooke's Law may also be stated in the same relation as Young's Modulus where "the strain in a solid…

A: Hooke's law is define as that the strain in a solid body is directly proportional to the applied…

Q: A disk between vertebrae in the spine is subjected to a shearing force of 670 N. Find its shear…

A: The shear modulus is

Q: The perimeter forming rate of the 45 ° jet shown in the figure is calculated when the strain rates…

A:

Q: A sculpture weighing 10,000 N rests on a horizontal surface at the top of a 6.0-m-tal vertical…

A: The stress of a material can be described as the amount of ultimate stress that can a material…

Q: The 3 nails in the figure can withstand an average shear stress of 40 MPa. Determine the shear…

A: Write the given values with the suitable variables. τ=40 MPa=40×106 Par=4 mm=4×10-3 m Here, τ and r…

Q: Compressive strain is the ratio between decrease in length and original length

A: To determine True and false statement regarding compressive strain

Q: A disk between vertebrae in the spine is subjected to a shearing force of 600 N. Find its shear…

A:

Q: A load of 300 N acts on a bar having a cross- sectional area of 0.6 mm2. The stress developed in the…

A: we know that,stress = force/area

Q: A 3.5 cm cube of unknown metal has a shear modulus of 5.0x 10°N/m ? absorbed a force of 0.40 N.…

A:

Q: it is a dimensionless value, classified into three types O Inertia O compressive stress, Bulk or…

A: Required :  Dimensionless value

Q: The ratio of stress to strain (o-4 / ɛ ) in the linear elastic region is . . called Young's

A: Y = streas/strain

Q: A rope of length 40.0 meters and 5.0 mm in diameter elongates by 1.0 meters when supporting a 50.0…

A: Given data:  Original Length (L) = 40.0 m Diameter (d) = 5.0 mm = 5.0 × 10-3 m Elongation in length…

Q: A sculpture weighing 10,000 N rests on a horizontal surface at the top of a 6.0-m-tall vertical…

A:

Q: -Force acting on thigh bone is 1800 N at compression causes longitudinal strain 3·10-3.1- Find…

A: Write the expression for Young’s modulus

Q: What is elastic modulus?

A: Elastic modulus

Q: The point that identifies the fracture point of the material whose graph of stress as a function of…

A: Answer            d) 5

Q: A thin rectangular plate is uniformly deformed, as shown. Determine the shear strain y, at P. Assume…

A:

Q: a cable has a diameter of 4mm and an original length of 2m.The cable is pulled by a force of…

A:

Q: Bone has a Young’s modulus of 18 x 109 Pa. Under compression, it can withstand a stress of about 160…

A: Write the expression for young’s modulus.

Q: The unit of Young’s modulus of elasticity is:

A:

Q: What is the modulus of elasticity? a) Ratio of elongation of

A:

Q: Sketch the stress-strain curve of the following tension test??? In the tension test of a metal…

A: Given, During tensile test metal fracture at maximum load Condition at initial is= Ao=150mm^2…

Q: Which modulus determines the stretching of a coiled spring?

A: Step 1When a coil spring is stretched or compressed, neither its length nor its volume changes,…

Q: Shear stress is calculated by dividing pressure by area. True False

A: False

Q: Describe the stress involved when stretching out a rubber band by pulling its ends apart

A: This question can be solved by using the basic concepts of stress and strain and properties of…

Mechanical Properties of Solids

There are three types of matter- solid, liquid and gas. Out of them, solids have a rigid shaped and size. The intermolecular forces of attractions in solids are greatest. Mechanical properties are the physical properties of a material which it shows, when it is provided with certain amount of force or load. These properties are to be kept in mind for various purposes. When a force is applied to an object, the object may or may not get deformed depending upon its elastic property. But every time the object develops a restoring force against the force applied. This is commonly known as stress. If the object changes its dimensions due to the force applied it develops strain ( which is the ratio of change in dimension to the original dimension).