What is the External flow over flat Plat

Q: ?What is the sp

A: Given data:

Q: What is propose of riser designed

A: To explain the purpose of riser design.

Q: ENT 152 Computer Aided Manufacturing I Milling Worksheet-SHOW ALL WORK A milling operation is to be…

A: Note :- you have posted multiple subparts on single question. As per the guidelines I am able to…

Q: feed rate for a theoretical surface

A: Given; Nose radius of a cutting tool=1.8 mmFeed rate for s theoretical surface roughness of;  Rt=5…

Q: How does an Electrical Discharge Machining remov material from work piece?

A: Electrical discharge machining is a process of removing the material with the thermo-electric…

Q: 2 cosh(lnx)

A: to find: 2cosh(lnx)

Q: 6. Among the following casting processes, do not need a parting Page 2 of 5 line. A. sand casting B.…

A: To select the correct option.

Q: are 3 methods that can be used to control the metal flow under the blank holder in deep drawing…

A: i.  Using Additional blank holder force,

Q: 3. Explain about pipeline pigging?

A: Solution:   Pigging in Pipeline is explained below:

Q: The shear angle

A: Given; Rake angle of orthogonal cutting of MS is;   α=100Chip thikness ratio=0.4Determine shear…

Q: Main advantage of the Forming taps is:

A: Form taps are ideal for tapping blind holes, but can be used for any tapping application in ductile…

Q: ulties

A: note : according to bartleby guidelines we can solve only first question for you please repost other…

Q: hearing is an example of __________________________________  Primary shaping process joining…

A: Note- There is a typing mistake as honing will be there instead of hearing. Honing is primarily used…

Q: Drawing is an example of __________________________________ primary shaping process surface…

A: Solution:

Q: Drag and Drop the name into label number. 3 4

A: In a modern pneumatic system, an FRL unit has three units namely Filter, Regulator, and Lubricator…

Q: RIS R12 frant sew R32

A: Given 3D model To find Three views

Q: A mandrel or steel rod is used to produce in drawing process.

A: Solution:

Q: 20)When a thick material is to be cut by WJC, one should prefer

A: All of these is correct according to given question for thick material so  Option d is absolutely…

Q: The most economical process

A: Given, A component can be produced by any of the four processes. Fixed cost and the variable cost is…

Q: e. What are the programmed feed material removal rate.

A: Given data; d=155 mmf=0.15 mm/revcutting speed(v)=150 m/min=150×103 mm/minfind the programmed feed…

Q: 150* 6. The component above requires equally spaced slots 2-1/2" apart over a 150" span. How many…

A:

Q: Match the processes with their characteristics.

A: Given; Following is the process and their chracteristics , So, We have to match the correct process…

Q: whether this is 2 Stroke or 4 Stroke

A: Given: D= 15 cm Piston speed=510 m/min BP=60 kW ηmech=0.80 Pm=5 bar=500 kPa CV=40000 kJ/kg To…

Q: Draw a FBD the tip to tail method please show steps

A:

Q: module is 4. What is the velocity ratio? *

A: The pitch circle radius as, r1+r2= r3+r4 (mz1+mz2)/2 =mz1+mz2)/2 z1+z2= z3+z4 30+90=40+z4 z4= 80…

Q: Match the following. Forging is an example of Choose. Choose. Drilling operation is an example of…

A: Forging is an example of     Primary shaping process

Q: What does the shear flow measure?

A: The shear flow is defined as the shear force per unit length in a thin walled perimeter. The…

Q: Misrun is a casting defect which occurs due to

A: Given. Misrun is a casting defect which occus due to following conditions;where,Casting defect is an…

Q: Friction less cannot be with cutting surfaces, during ansys simulation True False

A: Friction less cannot be with cutting surfaces, during ansys simulation True False

Q: Fill in the blank using R-134a

A: Using property table and P-h chart of R-134a, the required properties are taken.

Q: Could you please help me with my hw? Thank youu

A: Given that:  x = 3 sin 3t + 4 cos 3t   To prove :    a = - ω2x

Q: Give 1 example of methods of section

A:

Q: Deleimine wasik done

A: Given data : The value of force applied=F The value of displacement=D   To find : Work done

Q: F tonnes/hr Separation size required is -2 inch C tonnes/hr U tonnes/hr If the feed flow rate is 300…

A:

Q: 16)In which process Catcher is used

A: Catcher is used in abrasive water jet machining According to question option c is absolutely correct

Q: Is of a uniform flow filed, a d-

A: False

Q: 3- List two reason, to keep low pressure drop across the production system. 5- W... a

A: Pressure drop is the most common and significant problem observed in production system. It basically…

Q: What is the shear rate of a

A: Given: flow rate= 10 kg/min density=0.9 g/c L=10 cm w=25 mm t=3 mm To determine: shear rate

Q: _________ is a massive and rigid single piece casting made to support other active parts of a lathe…

A: The Answer is option [D] Bed.

Q: The cause of an induced angle

A: Solution ;

Q: Water jet cutting is one of several ways of cutting or trimming uncured or cured FRPS; in the case…

A: Q1: Water jet cutting is one of several ways of cutting or trimming uncured or cured FRPS; In the…

Q: 8. Name two ways that surface finish can be determined.

A: The surface finish is one of the most important part of the machine elements design. There are…

Q: Reduction ratio in the first and subsequent draws may not The minimum number of draws necessary will…

A:

Q: Pls heelp Blank is the time-honored tool for describing geometry

A: Given Geometry To find Fill in the blank

Q: need the solution in h

A: m1=200kgm2=300kgm3=240kgm4=260kgr1=0.2mr2=0.15mr3=0.25mr4=0.3mθ1=0°θ2=45°θ3=45+75=120°θ4=45+75+135=2…

Q: st common machining processes.

A: given: Name the three most common machining processes.

Q: What is the primary trend in yep-Ycg versus with water depth?

A: For solution refer below images.

Q: 15. Define with sketch the Hot-chamber machines

A: Given :- Hot chamber machines

Q: How shaper works please elaborate in 200 words

A: Shaper: It is a machine that is used to produce a horizontal, vertical, or inclined flat or plane…

Metal Casting

Metal casting is described as a manufacturing process in which a mold cavity is produced by sand, and molten metal is filled inside a mold cavity. The desirable shaped object is achieved after the solidification of molten metal. Large metal objects like machine beds, motor bodies, and others can easily be manufactured using metal casting. The place or shop where metal casting is performed is called foundry.