What is the permanent set of the bar? b) What is the length of the unloaded bar? c) If the bar is reloaded, what will be the proportional limit?

Q: A 100 mm x 5 mm x 5 mm steel bar free to expand is heated from 15°C to 40°C. What shall be…

A: As stated in question, Dimensions of the steel bar = 100 mm x 5 mm x 5 mm Initial temperature = T1 =…

Q: The engineering tensile curve of a cylindrical specimen of 10 mm diameter and 75 mm length…

A: a) Find the yield strength (0.2 % limit) So to find the yield strength (0.2% limit) it means we have…

Q: a square rod of 6061-T6 aluminum (cross-section = 4mm X 4mm, length = 2.3m). The material has a…

A: Given       Tensile load, P =3 kN        Cross-section = 4mm X 4mm Find The applied engineering…

Q: Can you please show me how to calculate the stress and strain on this figure. use this formula or…

A: For stress, σ=FA      F - applied load (known to you)                  A- effective cross section…

Q: The figure below is a stress strain curve for an alloy of aluminum at various temperatures. a) What…

A: (a) Draw the line at the Centre between the temperatures 250k and 350k. This line gives line of 298k…

Q: 1. The bar is made out of steel and is loaded as shown in figure Fig. - 1. Determine the design…

A:

Q: A steel rod of diameter 40 mm is subjected to a axial load of 60 N. The length of the rod is 10 m…

A: Given data: - The diameter of the rod is d = 40 mm. The axial load is P = 60 N. The length of the…

Q: In Figure 1, with its dimensions, loading status and material properties, different full circle…

A: Given data: The diameter of part AB is dAB=100 mm The diameter of part BC is dBC=80 mm The length of…

Q: An eye bolt carries a tensile load of 2000 kg. Find the size of the bolt, if the tensile stress is…

A: The tension is defined by the following: "The force of a string,…

Q: Figure shows a tie bar made of steel. When bolted between A and B double brackets, it is to be…

A: Given Data, P= Tensile load in the bar = 100 KN The bolt is of double brackets, so the shear load…

Q: The length of a wire increases from 1.25 m to 1.2508 m when a load of 12 kg is suspended. The radius…

A:

Q: A 30-m long aluminum bar is subjected to a tensile stress of 172 MPa. Find the elongation if…

A:

Q: The true stress (0), true strain (s) diagram of a strain hardening material is shown in figure.…

A:

Q: 2. A punch for making holes in steel plates is shown in Figure - 2 (a & b). Assume that a punch…

A:

Q: Can anyone give a step by step for this? No idea how to approach. Thank you!   The dimensions of a…

A: The 3003 h14 aluminum plate is a medium strength alloy that is made with 1.20 percent manganese. It…

Q: details are given, rivets and plates. Find the maximum shear, crush and tear (tensile) stresses.…

A:

Q: Given the shear modulus(G) for aluminum as 2.4e+10 N/m2 and the shear strain is given as 6e-5. What…

A: From hook's law  Shear stress is directly proportional to shear strain within elastic limit

Q: A 3.048 m annealed rod with a cross-sectional area of 555 mm2 was extruded from a 5083-0 aluminum…

A: Given: The initial length of rod, Li = 3.048 m The final length of the rod, Lf = 3.0518 m The…

Q: The bottom of a steel "boat" is a 5.00 mm ×× 9.00 mm ×× 2.00 cmcm piece of steel…

A: In the given problem, there is a steel boat. So, it must float over water. To float above water, the…

Q: Please answer both 1 and 2 as they relate to eachother. thank you in advance

A: Write the properties of 1040 steel.

Q: Rods (1) and (2) were supposed to fit exactly between the rigid walls at A and C, as indicated in…

A: Given DataE1=74 GPaA=1749 mm2L=738 mmE2=204 GPa

Q: PROBLEM 3 Steel: A = 500 mm ,= 120 MPa 1.8 Find the maximum allowable value of P for the column. The…

A: The normal stress developed inside a member when acted upon by an axial force ca be calculated using…

Q: In the system given in the figure, the rods are identical and it is desired to be produced in the…

A:

Q: A 35 kN axial load is applied to a metal bar with a rectangular cross-section, 28mm wide by 10mm…

A: To find: The original length of the bar. Given: The load is P=35 kN. The width is 28 mm and…

Q: A brass bar having cross-sectional area of 1000 mm? subjected to axial forces as shown below. Find…

A:

Q: A portion of the stress-strain curve for a stainless steel alloy is shown in Figure Q-2. A 350 mm…

A: Write the expression of the normal strain.

Q: What would be the compressive stress in MPa developed in the silica glass furnace tube constrained…

A:

Q: Question Two A steel flat of thickness 10 mm tapers uniformly from 60 mm at one end to 40 mm at…

A:

Q: Question Two A steel flat of thickness 10 mm tapers uniformly from 60 mm at one end to 40 mm at…

A: To find :  The percentage error  Given :  The thickness of steel flat plate is t=10 mm. The taper…

Q: A cable wire is used to hang 10-kg block of wood. If the allowable stress in the wire is 10 MPa,…

A:

Q: PROBLEM 4. The rigid bar is supported by a pin at A and two metal wires, each having a diameter of 4…

A:

Q: After the yield region in the stress-strain curve the strength up to ultimate value because:

A: When the stress is applied slip planes start to move in the direction of applied stress. Millions of…

Q: PROBLEM 4. The rigid bar is supported by a pin at A and two metal wires, each having a diameter of 4…

A:

Q: Question: Consider that the fit between the elements shown in the Figure below is H6/s5. They are…

A: given data

Q: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure…

A: GIVEN DATA- FOR STEEL AREA=500mm2 , STRESS=200MPa FOR AL AREA=400mm2 , STRESS=115MPa FOR BRONZE…

Q: Hooke's Law Part B - Calculate the elongation under load A bar with a solid square cross-section is…

A: Find the total elongation of bar and permanent change in length of bar.

Q: The tensile curve of a material is given on the side. a) Mark the strength points of the material on…

A: Given:

Q: The bottom of a steel "boat" is a 5.00 mm ×× 9.00 mm ×× 2.00 cmcm piece of steel…

A: Given: ρ-7900 kg/m3 Bottom side - 5 mm x 9 mm x 20 mm Thickness of side - 5.5 mm  To find : Height…

Q: A rubber block with dimensions of 120x120x120 mm is compressed in a rigid mold cavity with a…

A:

Q: 3-65: A stainless steel (SAE 301) wire is stretched between rigid supports so that a stress of 40…

A: Given data as per question Stress at supports = 40Mpa Temperature of the wire = 200 C Final…

Q: 2. The diameter of a bar fabricated from an alloy with properties show n in figure below reduced…

A: Find the original cross sectional area of the bar using the initial diameter. Ao=π4do2=π41.22=0.36π…

Q: A steel Column is 10m long and Ø1.2m. It carries a load of 102MN. Given the modulus of Elasticity is…

A: Given Length of column 'l'=10mDiameter of column 'ϕ'=1.2mLoad carried of column 'P'=102MN…

Q: Example: Convert the change in length data in Table 3-2 to engineering stress and strain and plot a…

A: Given data

Q: Aluminum A = 400 mm Bronze A = 200 mm Problem 2: An aluminum rod is rigidly attached between a steel…

A: Given dataMaximum stress in steel σmaxs = 140MPaMaximum stress in aluminium σmaxa = 90MPaMaximum…

Q: Made of steel alloy whose engineering tensile curve is given in the figure below, 10 mm diameter and…

A: a.From stress-strain cutve: The yield strength (0.2% limit)=400MPa b. Maximum load =Maximum…

Q: 1. Sketch stress-strain curves for the following three materials (mechanically worked tungsten…

A: Please find the answer below

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.