What is the Reynolds number for a straight and perfectly smooth pipe of length 500 m and diameter 0.2 m, transporting oil (density 900 kg/m3 and viscosity 0.5 Pa-s) at a flow rate of 100 kg/s from sea level to an elevated height 10 m above sea level? What is the viscous pressure drop along the pipe?

Q: 1) Convert the flow rate of natural gas is = 22.913x106 Sm3/s to m3/s ? Note: the gas export line…

A: Given that the molecular weight of the gas= 19.3,Relative density = 0.67 , Density = 670 Kg/m3 ;The…

Q: The following parts are not related. Also, please be concise. (a) Acetonitrile (density = 786…

A: Note: As per policy, we can solve the first question from multiple questions. Please resubmit the…

Q: A new steel pipe, 15 cm in diameter and 1200 m long carries 0.020 m^3/s of heavy fuil oil with S=…

A: Given question belongs to subject Fluid Mechanicas from Topic Flow through pipes.

Q: Consider a steady, fully developed flow in a horizontal pipe of diameter 80 mm. Over a section of…

A:

Q: A water tank used for fire fighting is shown in the figure. A fire extinguishing installation was…

A: (1) It is given that, The total length of the pipe is Apply Bernoulli's equation between section 1…

Q: Determine the size of clean wrought-iron pipe (e=0.046 mm) required to convey 250 L/s of oil,…

A:

Q: A 1/4” inside diameter pipe is used to transport SAE 30 motor oil (µ = 0.006266 slug/ft-s and ρ =…

A:

Q: Oil (SG oil = 0.95) flows at 200 L/s through a 200mm diameter pipe, 500m long. Friction factor is…

A: Discharge = 200 L/sor Q=0.2 m3/sdiameter (d) =200mm or d=0.2mlength of the pipe (L) =500mfriction…

Q: In Fig. a thick filter is being tested for losses. Theflow rate in the pipe is 7 m3/min, and the…

A: Given: The flow rate in pipe, Q = 7 m3/min The upstream pressure in pipe, P = 120 kPa The diameter…

Q: Sulfuric acid with a density of 1980 kg / m3 and a viscosity of 26.7 cP flows in a pipe with a…

A:

Q: A new steel pipe, 15 cm in diameter and 1200 m long carries 0.020 m^3/s of heavy fuil oil with S=…

A:

Q: B) Water flows in 50 mm pipe, 100 mm long whose roughness is 0.013 mm. If the pressure drop across…

A:

Q: It is desired to deliver 60 m3/h of water at 20°C through ahorizontal asphalted cast iron pipe.…

A: Given: The length of the pipe is L=100 m. The pressure drop in the pipe is ∆P=40 kPa. The volume…

Q: Compute the head loss (in meters) in 2000 m of horizontal, steel pipe with nominal pipe size of 300…

A:

Q: Sketch the shear stress and velocity distribution for laminar flow across a pipe section?

A:

Q: 9.42. In an established flow in a pipe of 0.3 m diameter the centerline velocity is 3.05 m/s and the…

A: Given:  d = 0.3 m  u=2.73 m/s u=3.05 m/s y= 75 mm = 0.075 m

Q: Oil flows in a pipe 80 mm bore diameter with a mean velocity of 0.4 m/s. The density is 890 kg/m3…

A:

Q: Prob. 2: Water at 20°C flows for 1 mi through a 3-in-diameter horizontal wrought-iron pipe at 0.557…

A:

Q: Use Poiseuille's Law to select the diameter of a 10-m long plastic pipe that is to transport room…

A: Given Properties of water at room temperature

Q: . Water having a kinematic viscosity v = 0.0000013m2/s flows in a 50mm diameter pipe at a veiocity…

A:

Q: lost in (30m) of this pipe is measured experimentally and found to be (533m). Calcne Water flow in…

A:

Q: An oil of sp.gr 0.85 is flowing through a pipe of diameter 425 mm at the rate of 450 liters per…

A:

Q: Water flows down an inclined tapered pipe 45 m long at a slope of 1:10. The areas at upper and lower…

A: GIVEN DATA- TAPER PIPE WITH SLOPE 1:10 PRESSURE AT UPPER END =100KPa AREA 8m2 AND 3m2 VELOCITY AT…

Q: A new steel pipe, 15 cm in diameter and 1200 m long carries 0.020 m^3/s of heavy fuel oil with S=…

A: Given Data: Diameter of pipe, d=15 cm Length of pipe, L=1200 m

Q: For a 34.4 mm diameter smooth pipe, calculate the threshold velocity (m/s) and corresponding flow…

A:

Q: A Bingham plastic with a yield stress of 120 Pa and apparent viscosity 1.6 Pa · s is to be pumped…

A:

Q: Medium oil with kinematic viscosity 6.10x10^-6 m²/s, flows through a straight pipe at a rate of 6.0…

A:

Q: Oil (SG = 0.87), with a kinematic viscosity of 0.007 ft2/s, flows in a 3-in.-diameter pipe at 0.19…

A:

Q: Water with a viscosity of u=0.01 kg/m.s and density =1000 kg/m is to be siphoned through a tube 30 m…

A: This question is solved with the help of Bernoulli's equation,  Bernoulli's equation is based on the…

Q: Water with a viscosity of u-0.030 kg/m.s and density = 1000 kg/m is to be siphoned through a tube 30…

A: Given:μ=0.030 Kg/msρ=1000 Kg/m3L=30 md=1.5 mmH=12 mhL=10 m

Q: 1. A 1.5-cm-diameter, 20-m-long plastic pipe transports water from a pressurized 400-kPa tank out a…

A:

Q: What size of new cast iron pipe (roughness of 0.00026) is needed. to transport 550 L/s of water for…

A: Given data as per the question Q=550 =0.550 m3s Length of pipe =1 km =1000 mhead loss =3m

Q: b (i) An 18.3 m long water pipe of diameter 12.7 mm delivers water at 5 USgal/min at 20°C. What…

A: Given Data: The length of the pipe is, L=18.3 m. The diameter of the pipe is, d=12.7 mm=12.7…

Q: Determine the Reynolds number for a flow of 25 ° C water in a 2 in diameter sanitary pipe at a rate…

A: Givenm˙=0.15kg/sv=m˙ρA=0.151000×π4D2=0.076m/sρwater=1000 kg/m3μwater=8.9×10-4 PaD=2 in=0.05…

Q: In a pipeline that connects a production oilfield to a tanker terminal, oil having density 953 kg/m®…

A: Given: density, ρ = 953 kg/m3 viscosity, μ = 0.287 kg/(m.s) diameter, d = 1.2 m velocity, V = 9.5…

Q: ter at a temperature of 800C (coefficient of viscosity is 0.357 centipoise) is flowing a ed of 200…

A: given:μ=0.357centipoise=0.0357N-s/m2speed v=200cm/s=2m/sradius r=2mm

Q: 1 Kerosene (20°C) flows at a rate of 0.04 m3 s in a 25 cm diameter pipe. Would you expect the flow…

A: GivenDiameter of the pipe =25 cmQ=0.04 m3

Q: Oil is to flow through a pipe at 80°C, and for experimental purposes, the oil flow must be…

A:

Q: Water at 25 deg C (998 kg/m 3 ) flows at 10 m 3 /s through a straight pipe of an ID of 1.38 m to 2…

A: Given: Density of the water→ρ=998 Kg/m3 Discharge of the flow→Q=10 m3/s Initial inner diameter of…

Q: Consider a duct with 100m in length, diameter = 0.1m and 2mm roughness that transports water at a…

A:

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.