Question

What  is  the  typical  hysteresis  at  the  input  of  a  Schmitt  triggered  gate?

Expert Answer

Want to see the step-by-step answer?

Check out a sample Q&A here.

Want to see this answer and more?

Experts are waiting 24/7 to provide step-by-step solutions in as fast as 30 minutes!*

*Response times may vary by subject and question complexity. Median response time is 34 minutes for paid subscribers and may be longer for promotional offers.
Tagged in
Engineering
Electrical Engineering

Analog Electronics

Related Electrical Engineering Q&A

Find answers to questions asked by students like you.

Q: If the stream 10110 is passed through an even parity checker and the parity bit gets added to the ri...

A: Given information: The bit stream is 10110 The bit stream is passed through an even parity checker. 

Q: Identify these op amps and the waveform that it produces. Thank you!

A: Click to see the answer

Q: A 150-volt electromotive force is applied to an RC-series circuit in which the resistance is 1500 oh...

A: Click to see the answer

Q: Hi, can you please help me with these question. Thank you.

A: NOTE: As per our rule we’ll answer the first question since the exact one wasn’t specified. Please s...

Q: What is the largest time delay that can be achieved using Timer0 and a pre-scaler? Assuming the micr...

A: Given: Timer 0 and a Prescaler is used to provide time delay. The microcontroller uses an external c...

Q: 2.7 a) The terminal voltage and terminal current were measured on the device shown. The values of v,...

A: Click to see the answer

Q: Given the circuit, solve for 1. Va, V. and Ve 2. AC circuit current ( m) 3. Resonant frequency (F 4....

A: Click to see the answer

Q: Give output function, transition table and State diagram by analyzing the Sequential circuit shown i...

A: The given circuit is designed using SR flip-flop. First draw the state table for SR flip-flop: S ...

Q: 1. The current entering the positive terminal of a device is, i = 2e-2t (A) and the voltage across d...

A: Write the power equation P= vi  

Q: Q2 and Q3 were collect. Please please help me.

A: To find the current through R4 and capacitor 

Q: For operation as an amplifier, the base of an npn transistor must be (a) positive with respect to th...

A: There are two junction present in an npn transistor. They are 1. Base-Emitter Junction (JE) 2. Base-...

Q: Lightning strikes a dielectric sphere of radius 15 mm for which e, =4.5, o 5 x 10- S/m and deposits ...

A: Click to see the answer

Q: Although current is blocked in reverse bias, (a) there is some current due to majority carriers (b) ...

A: When a pn junction diode is reverse biased, then the height of the junction potential barrier increa...

Q: I need to answer of this Control System Question

A: Click to see the answer

Q: What will be the radiation resistance of a dipole antenna whose effective length is equal to a quart...

A: Given information: The effective length of the dipole antenna is equal to a quarter of a wavelength ...

Q: • Solve for the value of constant(C) by obtaining the orthogonal trajectory of the given equation be...

A: Click to see the answer

Q: Consider the circuit in the given figure. Assume R1 = 130 Ω and R2 = 310 Ω.   Calculate current i in...

A: We can find current easily by using ohms law , i.e I=V/R

Q: 2. Calculate the power delivered (or consumed) by each element in the given circuit. Is the power ba...

A: Click to see the answer

Q: Consider the given figure where V1 = 45 V and V2 = 40 V. Use source transformations to reduce the ci...

A: Click to see the answer

Q: 2 A sequential circuit has two JK flip-flops A and B and one input x . The circuit is described by t...

A: Click to see the answer

Q: For the circuit shown in Figure, determine the power absorbed by the 5 ohm resiston ww 20 V ( ww

A: As all the elements are connected in series, considering the current flowing in the circuit is i, Re...

Q: what switch type and rating is required to control five 300 watt tugsten filament lamps on a 120 vol...

A: Click to see the answer

Q: Discuss power equation of synchronous motor

A: A synchronous motor coverts electrical power to mechanical power but always runs at synchronous spee...

Q: i need solve d and e.Thank you

A: As per your request , I'm gonna solve only sub parts d  & e.

Q: For the circuit in shown in figure 5, find the value for unknown capacitor C2

A: Given: Battery voltage E=333 V. Capacitor C1=12.5 μF, V1=8 V. Capacitor C2: Q=0.00113 C, V2 Volt.

Q: In the circuit, calculate the currents I and I1 and VAB

A: Click to see the answer

Q: Consider the generalized block diagram of an PLL. For any two stages of the block diagram ,consider ...

A: Click to see the answer

Q: The charge entering a certain element is shown in the given figure, where A = 70. Find the current a...

A: given: A = 70 Since it is known that current is given as: i=dqdtor,i=slop of the qt vs t graph So th...

Q: A 6-pole, 3-phase, 550 V, 50 Hz induction motor develops a power of 22.38 (10) kW at a speed of 950 ...

A: Click to see the answer

Q: In the circuit given below, R = 110 Ω. Find the value of io using mesh analysis.    The value of io ...

A: Consider the voltage across the current is vo.  The circuit diagram in which the current is mentione...

Q: Hi, can you please help me with the whole question. Thank you

A: Click to see the answer

Q: I:06)

A: Click to see the answer

Q: Using KVL, find the voltage across R3 for the circuit shown in Figure 1.

A: In mesh analysis, if the dominating mesh current is entering the voltage source then the voltage dro...

Q: Hi, can you please help mw with the whole question. Thank you

A: Click to see the answer

Q: i have provided answer ah part a so please i need b c and d

A: The K-map for the given function is given as  Thus the equations are given as   

Q: An inductor is energized as shown in the circuit in the figure. The resistance in the circuit its va...

A: Click to see the answer