What was the orginal size of the smallest outside diameter?

Q: What is the low limit on the smallest outside diameter?

A: Solution:

Q: Number 5  I put A and it was

A:

Q: Clue 6 in. the

A: The given conditions are: The thickness of the wooden plank is 78 inch. Average shearing stress =…

Q: ane area is

A:

Q: The angle of forst of c

A: Given; From given figure: A stepped shaft subjected to a twisting moment applied at BShear modulus…

Q: differentiate between shaper and planer machine any six difference

A: A shaper is a reciprocating type machine used to produce horizontal, vertical, and inclined surfaces…

Q: What is the total volume, in cubic inches, for bax fill calculations using two internal clamps, six…

A: Given data   Components are : Two internal clamps six THWN copper conductors two single pole…

Q: What would it be in celcius

A: From the result, the final temperature of the air in the tank is 277.3 K

Q: Discuss how the Cylindrical Square is used.

A: A cylinder square is used for checking the squareness of vertical axis with reference to horizontal…

Q: A B - 3 ft - 6 ft - 3 ft 2 in. 6 in. 2 in. I in. in.

A:

Q: The major diameter of a thread is defined as what

A: A thread is a bank of the constant section in the form of a helix on the internal or external…

Q: the force needed to deflect 1 inch of length is called

A: The force needed to deflect one inch of length can be called as stiffness.

Q: e of 400 N is a dentical bar of noro?

A: given:E=400N

Q: Question 8  I put C and it was incorrect

A: To determine: Correct technician among A and B who are discussing the suspension and ignition switch…

Q: ed part are include the unshaded are

A: we will consider donut shaper figure Area = outer circle - inner circle outer circle radius =2…

Q: Dad with an angle of 10° and radius

A:

Q: What is the lowest allowable dimension for the flats?

A: Solution:

Q: Fill the blanks correctly and define

A: Given: For apinion of 15 teeth,where, Pinion is usually a two meshed gears. It is used in several…

Q: The minimum possible thickness

A: Given; A thick sheet having 4 mm is rolled with 300 mm diamaterOr, d=300 mm t=4 mmFriction…

Q: What is the other name for the short column?

A:

Q: is filled to height|

A: given:A=525in2h=67inmass m=56slug

Q: What’s the answer for this please ?

A: Option d is correct .  Regeneration :- this is done by preheating the compressed air before entering…

Q: What is the percentage of rods

A: Given; Determine the percentage of rods whose lengths lie between 438 mm and 441 mm.Where, The…

Q: 4. WHAT IS THE VOLUME OF THE PART?

A: Given:- Unit:- MMGS Material:- Copper To find:- 1) Volume 2) Mass 3) Center of mass

Q: Answer the following elating to the drawing in figure (38): 1- What is the name of the component? 2-…

A: A rotational or sliding motion for two parts or maybe more or support an applied load is a shaft…

Q: The largest soft aluminum tubing that may bent by hand is ________________ -inch outside diameter. *

A: Solution:

Q: 1 in.- a 1 in.

A: Given

Q: with proper value

A:

Q: Riser is designed so as to ?

A: Riser is part of gating system in casting process. The gating system includes pour basing, sprew,…

Q: The time taken to drill a hole

A: Given; Feed rate of a drill is;   f= 0.25 mm/revAt a rotating speed at, N= 300 rpmWhere, Plate…

Q: 6 kip/ft 8 kip AB A 9 ft 4.5 ft 5 ft -

A:

Q: A thin brass pipe, 3 cm in outside diameter,

A: Refer attachment Please

Q: Which distance represents height of the fall for measurement of the time?

A: In the question, a machine is given and when it rotates it is needed to find out the height and time…

Q: Shape Area

A:

Q: what is the external heating surface area in square feet of a tube with the following dimensions:…

A: Given data: Inside diameter of tube = d = 5 inch Thickness = t = 0.5 inch We have to find the…

Q: In step 4, it should be the A and not the y right? So it should be FBD divided by 4.04 which is the…

A:

Q: what would you do if it was a through hole that went all the way through the 6 inch shaft?

A: Given question:   what would you do if it was a through hole that went all the way through the 6…

Q: Need three views

A: According to the details provided in the question, we need to find three views.

Q: The cause of an induced angle

A: Solution ;

Q: Find warrk done

A:

Q: Draw pressure diagrams

A:

Q: What will be the distance

A: Given; A leaf is caught in a whirlpool.Leaf distance=120mThe whirlpool can be described by the…

Q: If a washer has a 1” outside diameter and a .50” inside diameter, what is the distance between the…

A: Given data, D= 1 in.  d= 0.50 in.

Q: What is the counterclockwise angle?

A: The counterclockwise angle is the angle measured in the opposite direction of the clock.

Q: 4. What is the length of the longest part?

A: To find Length of longest part.

Q: the time needed to cool the object

A: Given: A body is cooled from temperature A to B at surrounding temperature To To determine the time…

Q: A rod consists of two parts that are made

A: Kindly refer attached files.

Q: The appropriate diameter is mm.

A: To find  diameter

Metrology of Screw Threads

Screw threads are a series of ridges having the profile of a helix. This helix profile runs continuously along the length of a uniform solid or a hollow bar of a circular cross-section at periodic intervals. These helix ridges are also formed over a conical bar. These continuous helical ridges are termed threads.