When installing a new release bearing, Technician A says the outer surface of the transmission's front bearing retainer should be lubricated. Technician B says the release lever and pivot shuold be lubricated who is correct? a. techincian A b. Technician B c. both A and B d. Neither A or B

When installing a new release bearing, Technician A says the outer surface of the transmission's front bearing retainer should be lubricated. Technician B says the release lever and pivot shuold be lubricated who is correct? a. techincian A b. Technician B c. both A and B d. Neither A or B

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter41: Automatic Transmissions And Transaxles

Section: Chapter Questions

Problem 1ASRQ: Technician A says that bearings that take radial loads are called Torrington washers. Technician B...

See similar textbooks

Related questions

Q: Q1- Explain the duties of camshaft, distributor and alternator, which are among the engine parts

A: Camshaft Camshaft is the shaft at which many cams are connected and it operates with the crankshaft.…

Q: An engine may be equipped with all the following belts, except? Select one: a. A serpentine belt b.…

A: Given that An engine may be equipped with all the following belts, except? Select one: a. A…

Q: Explain the benefits of dynamic testing of automatic transmission fluid

A: Automatic transmission fluid: It is a type of fluid which is used in vehicle for self-shifting and…

Q: Which of the following screwdrivers is like a Phillipsbut has a flatter and blunter tip?a.…

A: Screwdriver tip with conical sides and the Phillips screw symbol A cross-head screw with parallel…

Q: vards the left on the slider. The I 0 mm. Ignoring the effect of grav ankshaft torque (in Nm) needed

A: GIVEN:l=70mmr=30mmθ=450

Q: List 5 Manual-Transmission Troubles and described each.

A: Please find the answer below

Q: What are the 4 main function of the clutch?

Q: When discussing the various gear positions of a transfer case, Technician A says that when the…

A: Transfer case is used to switch from two wheel drive to four wheel drive and vice versa. It also…

Q: While discussing the fail-safe function: Technician A says that the 4WS indicator light is…

A: The statement given by technician A is correct as when the fail-safe function that is when the any…

Q: 2. Technician A says that load-carrying ball joints should always have some play in them. Techni-…

A: The ball joints basically serve as the pivot point between the tyre and the suspension in an…

Q: What determines whether a conventional transmission or a transaxle is used?

A: Manual transmissions feature a foot-operated clutch pedal and a shifter that allows the driver to…

Q: Technician A says that double-cone synchronizers have friction material on both sides of the…

A: Technician A says that double-cone synchronizers have friction material on both sides of the…

Q: A clicking noise during transmission/transaxle operation may be an indication of .

A: Given data Why clicking noise during transmission transaxle operation is the indication of ..?

Q: Briefly explain how a diaphragm clutch works.

A: Note:- As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: Which of the following is part of the sprung weight ofa vehicle?a. Steering linkageb. Tiresc.…

A: A vehicle’s sprung weight is supported by springs of one kind of or another (coiled springs, air…

Q: Why is mixing different manufacturer’s bearings typically not recommended?

A: Bearing: It is a mechanical element or part which allows the relative motion between two parts and…

Q: How are problems normally first noticed with the differentialand drive axles?

A: SYMPTOMS OF A DAMAGED DIFFERENTIAL Other components may show signs of damage when your vehicle has…

Q: Three factors to consider before deciding to apply a transmission of gear drives

Q: Why do we need to diagnose the transmission/transaxle failure?

A: It is very important to diagnose the transmission failures in any vehicle.There are many factors…

Q: technician a says that an oil-soaked clutch dis can cause clutch chatter technician b says that…

A: Solution:

Q: Insufficient clutch pedal clearance results in_ _ _ _ _ _ _ _ _ .a. gear clashing while shifting…

A: Answer is option C

Q: Technician A says that limited- slip differential clutch packs are designed to slip when the vehicle…

A: Limited-slip differential clutch packs is a modification to the regular differential mechanism. LSD…

Q: Which of the following is a good definition of SAI?a. Forward tilt of the top of the steering…

A: Given Data : SAI

Q: Shift linkage enclosed within the transmission or transaxle case is called as 1) external linkage 2)…

A: Column Shift: In a column shift there is a rod which connects the handle with the lever attached at…

Q: when discussing shift problems, technician A says that worn or broken engine and transaxle mounts…

A: The explanation of technician A is correct because the shifting problems may cause due to worn or…

Q: Which of the following is NOT true about the initial tension in a flat belt drive? OA. It should be…

A: A spherical joint is also known as ball and socket joint, allows three relatives rotation between…

Q: The clutch friction disc always rotates with the

Q: Technician A says hypoid gearset are only used in RWD vehicle drivetrains. Technician B says hypoid…

A: Hypoid gear is spiral bevel gear in which the axes doesn't intersect and it is not parallel. This…

Q: When reviewing the service procedures for CV joints and drive axles, Technician A says that the axle…

A: The axle can be used as a slide hammer to help remove a stubborn inboard joint from the transaxle as…

Q: While discussing transmission adaptive learning: Technician A says that the transmission learns to…

A: Transmission Adaptive learning:-The automatic transmission is designed in such a way that it has a…

Q: When reviewing the procedure for replacing an axle boot, Technician A says that the position of the…

A: Understand that when the old boot is removed the new boot is used to replace the old one at the same…

Q: 128) Technician A says slide hammer pullers are usually required to remove the front pump from the…

A: A slide hammer puller is a mechanical tool with a long round shaft. It has a hammer weight slides. A…

Q: Technician A says a wheel alignment rack should include rear slip plates. Technician B says a four…

A: During the alignment lift operation, it is necessary to take off slip plates. To give a better wheel…

Q: The drive shaft component that provides a means ofconnecting two or more shafts together is the __…

A: Various types of joints are used to join the shaft with each other to transmit power from one shaft…

Q: While inspecting a planetary gear-type final drive, Technician A says blackened pinion shafts…

A: Technician A is right as blackened pinion is a sign of overloading and are used as indicators of…

Q: number of pe f the pinion

Q: list five checks that should be made during the visual inspection of the parts of a…

A: The mechanism with he help of which the power generated inside the engine transmitted to the wheels…

Q: Explain any one type of coupling which can be used to connect two aluminum alloy shafts when there…

A: Oldham Coupling is used to connect the two shafts which are in lateral misalignment.

Q: Is the car clutch failed due to static load or cyclic load?

A: Given data Is the car clutch failed due to static load or cyclic load.

Q: mm - The mating shaft has a clearanc

Q: The knocking is usually occurred at the low engine speed O a. True O b. False

A: True

Q: Which of the following screwdrivers is like a Phillips but has a flatter and blunter tip? a.Standard…

A: Given Data : Screwdrivers Phillips

Q: On most vehicles, the automatic adjuster cablesor levers are ___.a. installed on the secondary…

A: Given Data : Automatic adjuster cables

Q: When discussing shift problems,Technician A says that worn or broken engine and transaxle mounts can…

A: Transaxle generally faces the same failure and shifting mechanism as the transmission system in the…

Q: What type of axle housing resembles a banjo?

A: Given Data : Banjo

Q: What safety precautions must be observed when carrying out diagnosing procedure on drive shafts?

A: Depending on the performance outcome, the correct diagnose required in the drive shaft of the light…

Q: Technician A says that shift solenoids direct fluid flow to and away from the apply devices in the…

A: The basic function of shift solenoids is to control the pressures within fluid system and they don’t…

Question

When installing a new release bearing, Technician A says the outer surface of the
transmission's front bearing retainer should be lubricated. Technician B says the release lever and pivot shuold be lubricated who is correct? a. techincian A b. Technician B c. both A and B d. Neither A or B

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Introduction

VIEW

Step 2 Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Technician A says that jack stands should always be used with portable floor jacks. Technician B says lifting capacity and operation should be checked before using a floor jack. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor B
type of bearing respecrively A,B,and C ?
when discussing shift problems, technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems. technician b says that poor shift boot alignment can cause a transaxle to jump out of gear
What additional force A is needed to keep the block in static equi
Technician A says that the piston seal retracts the caliper piston when hydraulic pressure is released. Technician B says that a return spring is used to retract a caliper piston. Who is correct?
__________ is connection between the bit and the surface, where the torque is generated. Which helps in power transmission. a. Drill string b. Drill Collar c. Swivel d. Kelly
The amount of force generated by an air bearing decreases when?
Technician A says that bearings that take radial loads are called Torrington washers. Technician B says that bearings that take axial loads are called thrust washers. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
Technician A says that shims may be used to adjust shaft end play. Technician B says that snap rings may be used to adjust shaft end play. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
When discussing shift problems,Technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems.Technician B says that poor shift boot alignment can cause a transaxle to jump out of gear?
Is a hook good on a compression spring launcher trigger mechanism
While inspecting a planetary gear-type final drive, Technician A says blackened pinion shafts indicate severe overloading. Technician B says bluish gears indicate overheating. Who is correct?