Which of the following is not part of the starter motorcircuit?a. Batteryb. Starting safety switchc. Starter motord. Relay solenoid

Q: What is the unit of strain? a. any unit. b. lb c.in/in d. lbf/in

A: Strain : The ratio of change in length upon original length is called strain . Strain=Change in…

Q: Determine the forces in members BC and CF of the loaded truss. Enter a positive number if in…

A:

Q: Determine the magnitude of the resultant force and its direction measured from the positive x axis.…

A:

Q: A 1- Threshold shown in Figure (2), calculate the reactions in datums A, F and E 1.5 m 1.5 m 450 N…

A:

Q: 30 kN Find the reactions in datums A and B for the threshold shown in Figure 3. A 10m 3.0m 125 KN 45…

A: The reactions in datums A and B are: ◆ Ax = 15 kN , Ay = 85.31 kN ◆ Bx = 0 kN , By = 110.67 kN

Q: What is acoustic supercharging?

A: Intake reverberations are related to acoustic supercharging. Rather, it refers to the number of…

Q: The sphere P travels in a straight line with a speed v = 8.1 m/s. For the instant depicted,…

A: Given: x = 5.2 m y = 3.5 m φ = 25° v = 8.1 m/s

Q: An industrial plant requires that 12,000 kg/s of water be cooled from 40℃ to 30℃. Inlet air for a…

A:

Q: 8. Two equal forces are acting at a point with an angle of 60° between them. If the resultant force…

A: As given in question, Let us consider two forces acting at a point F1 and F2. As these two forces…

Q: Describe the two basic types of passenger weightdetection sensors used in most vehicles

A: given;; Describe the two basic types of passenger weight detection sensors used in most vehicles.

Q: Which process would best represent the opposite ofexhausting air from a system?A. CoolingB.…

A: Given Data : Exhausting air

Q: Example 3.6 The gate in figure below is 5 ft wide, is hinged at point B, and rests against a smooth…

A:

Q: 3.1 figure 2 shows a cross-sectional view of an concrete dam wall. the width of the dam wall is 25…

A:

Q: While testing variable resistors: Technician A saysthat while checking a rheostat with a voltmeter,…

A: Given Variable resistor To find Which technician procedure is correct

Q: Q1: A prybar is used to remove a nail as shown. Determine the moment of the 80-lb force about the…

A: Given data as per the question Force =80 lb θ=25-15=100

Q: Rotation of bar OA is controlled by the lead screw which imparts a horizontal velocity v = 31 mm/s…

A: The stepwise procedure to solve this problem is shown in the following attached image:

Q: Problem #5: A homogeneous 62-kg block is suspended by three springs whose lower ends were originally…

A:

Q: X 35 kPa 40 kPa 95 kPa

A: As stated in question, Stress along x-direction = σx = -95 kPa Stress along y-direction = σy = -35…

Q: 2. In order to meet the requirements of machining quality, efficiency and economy, how to arrange…

A: In machining, process material is removed from the surface of the workpiece with the help of a…

Q: A steel bar with a diameter of 100 mm is rigidly attached to the wall and carries the loads shown in…

A: Given: The diameter of shaft, d = 100 mm = 0.1 m The torque acting on the shaft, T = 8 kN.m The load…

Q: the plate. Consider the temperature of the wind/air as 20 °C and assume that the wind speed does not…

A:

Q: What is the kinetic energy of an 1800 kg car moving at 25 m/s?

A:

Q: Two uniform spheres are positioned as shown. Determine the gravitational force F which the titanium…

A:

Q: 9. Which of the following is not a scalar quantity (A) Time (B) Mass (C) Volume (D) Acceleration

A: To find : which of the following is not a scaler quantity

Q: cific gravity and net calorific value of fuel oil is 0.92 and 9700 kcal/kg respectively. Find the…

A: Given as, T2=1300°C,T1=50°C,∆T=1300-50=1250°C.

Q: The magnitude of the reaction in the datum C shown in the figure is equal to

A:

Q: 4kN/m 4m 2kN/m

A: GIVEN DATA- A simply supported beam with trapezoidal load given we have to draw SFD and BMD

Q: Composite headlights are being discussed: TechnicianA says that they have replaceable bulbs.…

A: Given Composite headlights To find Correct technician

Q: 30 kN 60% +1.0 m Find the reactions in datums A and B for the threshold shown in Figure 3. 3.0 m 125…

A:

Q: For the system of forces shown in Figure (4), find the resultant and direction of the forces and…

A: Given question : For the system of forces shown in Figure, find the resultant and direction of the…

Q: A pump draws water from a well through a vertical pipe 15 cm in diameter. The bomb drains through a…

A:

Q: The normal minimal cranking voltage specification isapproximately ___ .a. 9.6 voltsb. 10.5 voltsc.…

A: When starting an engine, the voltage that is available on the starter is known as the cranking…

Q: Line AB 100 mm long is 30° and 45° inclined to HP & VP respectively. End A is 10 mm above HP and…

A:

Q: find the reaction at roller support at B find the reaction at the external pin support at A Find…

A: The free body diagram of the beam is given below,

Q: a Show how Pip can complete the circuit by adding less than 120 cm of track. b Show how Pip can…

A:

Q: Which of the following is a good definition of SAI?a. Forward tilt of the top of the steering…

A: Given Data : SAI

Q: The equation of this best-fit line will have the familiar form y = mx + b, where m represents the…

A: given;   a. how will you calculate the value of the slope of this best-fit line? b. How will the…

Q: The culture of an organisation makes the greatest contribution to its health and safety performance.…

A: When a workplace or the work itself is dangerous, it might indicate that management of the…

Q: An overhanging beam ABC has a guidedsupport at A, a rectangular cross section, and supportsan upward…

A:

Q: The number of equilibrium equations that are used to analyze the kinematics using the joint method…

A: The number of equilibrium equations that are used to analyse the kinematics using the joint method…

Q: Find the work done in pushing a car a distance of 8 meters while exerting constant force of 900 N.

A: Given data : Force F=900 N Displacement d=8 m   Required : Work done

Q: Describe a direct-expansion versus a flooded evaporator.

A: Flooded Type Evaporator: Compared to a dry type, a flooded type evaporator transfers heat more…

Q: The type of condenser that has the lowest operating headpressure is the _______ cooled condenser.

A: Given Data : Condenser

Q: A simply supported wide-flange beam ofspan length L carries a vertical concentrated load Pacting…

A: Given Beam = W250 X 44.8 L = 3.5 m Angle = 26.57 P = 18 kN To find Magnitude of beta Maximum stress…

Q: 4. For the motion of block B in the system below use the following values: VB = 4 m/s; ag = 2 m/s².…

A:

Q: While discussing the different types of pressureplates: Technician A says that coil spring types…

A: Option D is the correct naswer

Q: A venturi meter has air flowing through it. The diameter at the entrance is 2.5 in and at the throat…

A:

Q: What is the advantage of using heat exchanger in plant designing compared to other heat transfer…

A: Introduction: Heat exchangers are devices that transmit thermal energy between two or more fluids.…

Q: A hot plate 1.2m wide, 0.35m high and at 1 is · Calculate the following  Local heat  transfer…

A: Given Wide = 1.2 m Height = 0.35 m To find Local heat transfer coefficient Average heat transfer…

Q: The car is traveling at a speed of 58 mi/hr as it approaches point A. Beginning at A, the car…

A: Given:   VA = 58 mi/hr =58×52803600=85.07 ft/s Let Velocity at B = VB aA-B = 6.1 ft/s2 aB-C = 2.6…

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.