Write "open" or "closed" in the blanks below: When cylinder 1 is moving, check valve 1 is When cylinder 1 is moving, pressure control valve 1 is When cylinder 2 is moving, check valve 2 is When cylinder 2 is moving, pressure control valve 2 is

Q: Choose correct answer: The main parts of the time delay valve are one-way flow control valve ,3/2…

A: Time delay valve is used to control the operation time as per one's need. The valve is actuated by a…

Q: 13) Write a program to implement the process illustrated in the figure below. The sequence of…

A:

Q: i. Describe the operation when valves 1 and 2 are in the positions as shown. ii. What would happen…

A: The  two way valves is  fill and drain a vessel is given.

Q: I need problem 8 answered pertaining to the print and sequence of operations that is both provided.

A: A pneumatic control system is designed in the form of pneumatic circuits. The pneumatic system…

Q: Briefly describe what is meant by a right handed system of coordinate

A: System of cordinates -  A cordinate system is defined as a system which is used to define the…

Q: I need parts 5 and 6 answered pertaining to the print and set of sequence of operations.   Note: If…

A: When the operator actuate the two-push button valves (1) and (2) until the weight starts to descend.…

Q: Based on the circuit shown in Figure 19-11, complete the following exercises: A. Complete the chart…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: provide Orthographic view

A: Question fig.

Q: the following is not one of the nonmachine tool applications of numerical control.   Question 24…

A: None of the above is the correct answer

Q: A major disadvantage of on/off control is that it cannot work for applications requiring very small…

A: On-off controller (also called two-step controller) turns on or off the machine based on the error…

Q: Instruction: Complete the following table of Pneumatic Symbols. Name Symbol Name Symbol Pushbutton…

A:

Q: In a tap set, the plug tap is the final one and is also known as taper tap. Select one: True False

A: Plug Tap

Q: In the drilling process shown in Figure 1, there are which cylinders A and B are used to clamp the…

A:

Q: I need parts 8, 9, and 10 answered pertaining to the print provided and the set of sequence…

A: If intake and exhaust will be on the same side of cylinder head then this is a reverse flow and…

Q: What are the four ways we put fluids to work

A: Crystalloid IV solutions contain small molecules that flow easily across semipermeable membranes.…

Q: Basically a CNC machine runs on a program fed to it through Punched tapes Select one: True False

A: Computer Numeric Control (CNC): It is a machine which works on the computer program based on the…

Q: Draw the block diagram for a garage door

A: In this problem, it is asking about the block diagram of garage door system.

Q: t is desired to operate a double acting vertical hydraulic cylinder supporting a  load .…

A: To start with let us first define what is double acting vertical hydraulic cylinder: Double acting…

Q: ite a for loop to print all even numbers betw . Repeat with a while loop. . Write a for loop which…

A: 14. For loop to print even numbers b/w 1 to 20For m=1:20If (mode(m,2))=0display(m)endend15. Repeat…

Q: Choose correct answer: In direction control valve symbol with numbering system 2, 4,6&8 indicates…

A: Given:

Q: Write down the name of Primary Control Surface

A: The rudder is a fundamental control surface which is typically controlled by pedals rather than…

Q: Respond with TRUE if the symbol of the valve shown below is drawn correctly . select true or false

A: Solution:

Q: 1. How is the cylinder 3A (towards the right) fundamentally different than cylinders 1A and 2A? 2.…

A: To find : 1- how is the cylinder 3A (towords the right )fundamentally different than cylinder 1A and…

Q: A single cylinder engine is used to drive an irrigation pump. The set-up has the following data:…

A: The diameter of the pump pulley: 305.5556 mm

Q: A fixed rating pressure switch is adjusted inside the pressure control and display console to record…

A: Fixed rating pressure switch cannot be adjusted inside the pressure control because due to fixed…

Q: Which of the following settings does not allow you to control point specifications?a. Grid b. Snap…

A: From the given options, the snap, ortho and the polar settings are used to specify a point. Hence…

Q: Devise a mechanical models for the crane of the following Figure Steel cable W Steel boom

A:

Q: Problem: Boxes (or certain production parts) are moved by a double acting cylinder away from a…

A: iam drawing circuit diagram using PneumaSolver software.

Q: Basically a NC machine runs on a program fed to it through Punched tapes Select one: True False

A:

Q: Instruction: Complete the following table of Pneumatic Symbols. Name Symbol Name Symbol Compressor…

A: The complete table of Pneumatic symbols are shown in the following attached image:

Q: Interchangeability system is also called

A: Solution:

Q: There is a 20' tank that has one pump to fill the tank. There are two pumps that will be involved in…

A: Given : To find : PLC diagram

Q: Which may not be an input of a control system? * actuating signal; setpoint; controlled variable;…

A:

Q: 4. Describe the sequence of events that occur as the manually operated directional control valve in…

A: 4.     A sequence valve is a pressure valve that opens when the predetermined pressure is…

Q: esign the additional comp-

A: Required which design is used components in series and parallel

Q: Basically a CNC machine runs on a program fed to it through Punched tapes Select one: True O False

A: CNC (Computer numerical control) machine is a NC machine which uses a dedicated computer as the…

Q: 1)how two directional control valve should be installed in a system to operate alternatively an…

A: 1.1)how two directional control valve should be installed in a system to operate alternatively an…

Q: Read each statement carefully and fill in the blank(s) with the correct answer. 1- Pressure…

A: 1. analog electrical signal 2.97% 3. run and time button

Q: Describe the following point-of-operation devices: (a) automatic or semiautomatic feed and ejection…

A:

Q: A pictorial view of a machinebracket is shown in the figure. Draw using the first angle projection…

A: first angle projection

Q: where is starting point

A:

Q: a DCV, this part moves the spool, it can be a lever or a button a. operator b. springs c. spool…

A: The solution is attached below:

Q: Blocked suction cylinder unloading is accomplished byA. keeping the suction valve closed.B. closing…

A: given; Blocked suction cylinder unloading is accomplished by

Q: A The symbol shown represents a: Normally Closed Pressure reducing valve. Normally Closed Pressure…

A: A pressure-reducing valve maintains lower pressure in branches of the hydraulic system. The system…

Q: Give the name of the following graphic symbols or Draw the graphic symbol according to the following…

A:

Q: Surveyor's measuring rods in 3 or 5 m length are as shown in Figure 1. There is a choice of two push…

A:

Q: employ a pointer moving over a fixed scale.

A: The correct answer for this question is  Indicator employs a pointer moving over fixed scale

Q: Write a brief introduction about control of furnace door (OPEN ENDED) . Note:Include all the…

A: Given: There are automatic door of the furnace and automatic supplier of the fuel to the furnace. In…