You are a structural Engineer who works in Dar Al Handasah company. Your manager has called for a meeting and provided you with the below schematic design of a concrete beam that might be implemented at one of the sites. You were requested to calculate the following: (make 15 KN bold) 40 KN 15 KN 20 KN 45 30 KN 40 KN 16 20 Figure 1: Concrete Beam 1. Find the equivalent forces of the disturbed loads. 2. Sketch the beam showing all the applied forces (reaction and equivalent forces) and allocate them into their suitable locations proper points. 3. Apply the moment equations in the equilibrium state to find the value of the reaction forces at points A and B. 4. If the given beam in Figure 1 compressed shrank to be 19.98 meter where the original temperature was at the given temperature T1=200 K, find the temperature (T2) after the compression shrinking.

You are a structural Engineer who works in Dar Al Handasah company. Your manager has called for a meeting and provided you with the below schematic design of a concrete beam that might be implemented at one of the sites. You were requested to calculate the following: (make 15 KN bold) 40 KN 15 KN 20 KN 45 30 KN 40 KN 16 20 Figure 1: Concrete Beam 1. Find the equivalent forces of the disturbed loads. 2. Sketch the beam showing all the applied forces (reaction and equivalent forces) and allocate them into their suitable locations proper points. 3. Apply the moment equations in the equilibrium state to find the value of the reaction forces at points A and B. 4. If the given beam in Figure 1 compressed shrank to be 19.98 meter where the original temperature was at the given temperature T1=200 K, find the temperature (T2) after the compression shrinking.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 38.0 kg beam is attached to a wall with a hinge while it’s far end is supported by a cable such that the beam is horizontal. If the angle between the beam and the cable is θ = 69.0 ° what is the vertical component of the force exerted by the hinge on the beam?
P235 - The gate below is an isosceles triangle with 3m side. What is the proper configuration, the triangulate upright or inverted, so that the forces are as minimal as possible? - What would the forces be like in a circular 3m radius floodgate?
An 87.5 kg fisherman sits at the center of the boat, which has a uniform width and a weight per linear foot of 4.1 lb/ft. The boat is 13 m long. Assume that the water exerts a uniform distributed load upward on the bottom of the boat. a. What is the applied load (lb) applied to the boat due to the weight of the fisherman? Round up to the next whole value.b. Using the applied load at Item 9.a, what is the maximum shear force (lb) exerted on the boat?c. What is the maximum bending moment (lb-ft) exerted on the boat?d. At what distance from the left side of the boat the maximum bending moment occurs?
Physics In a simple supported beam , write the moment equation of the beam shown in this video if it is loaded with 10 kN/m uniformly distributed over the entire simple span of 4 meters and a concentrated load of 20 kN applied 2 meters from the left support. Present your answer using the GAPSA form by indicating all the given data, what is being asked in the problem, the appropriate formula, the entire solutions / calculations and the answer accompanied with corresponding unit of measurement. Thank you.calculate the moment equation and the segment ,using double integration method
Floor joists are structural members which support flooring in structures, as in the diagram on the right. The floor sits upon the minor length of the joist, and the joists are set at equal spacing to reach the desired floor stiffness. How many 2x6 joists would it take to equal the floor stiffness of the same floor supported by ten (10) 2x12 joists of the same species?
SHOW YOUR SOLUTIONS PLS, INSTRUCTIONS: For the beam shown, (1) derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) (2) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Specify the values for key points on the diagrams. Let a=7.0 ft, b=8.7 ft, wa=13 kips/ft, and wb=7 kips/ft. QUESTIONS: 4) With reference to problem 1, what is the bending moment (in kip-ft rounded to the nearest whole number) at x = 9.0 ft? 5) With reference to problem 1, what is the maximum bending moment? Express your answer in kip-ft rounded to three significant figures.
A board of mass mand length l is attached to a wall and a rope that makes an angle of theta, as shown. A block of mass M hangs from the right end of the board. Suppose m = 2.0kg, L = .60m, M = 0.50kg, and angle(theta) = degrees. a. Using numbers, what is the magnitude of the tension force in the rope connecting the board and wall? b. Using numbers, what is the magnitude of the force applied by the hinge? c. Using numbers, in what direction does the force applied by the hinge point?
A) Imagine a procedure used for the execution of a certain work, as shown in the following figure. Such a crane has a mass of 1000 kg and is transporting a coffin with a total mass of 2400 kg. Assume that support A is fixed, support B is movable, and point G is the center of gravity of the lift. What are the support responses in kN? Question 1 options: a) The support responses are as follows: Rax = Rbx = 34 kN and Ray = 109.33 kN. b) The supporting responses are as follows: Rax = Ray = 109.33 kN and Rbx = 34 kN. c) The support responses are as follows: Rax = 56.8 kN; Rbx = 109.33 kN and Radius = 34 kN. d) The support responses are as follows: Rax = 156.7 kN; Rbx = 89.65 kN and Radius = 34 kN. e) The supporting responses are as follows: Rax = Rbx = 109.33 kN and Ray = 34 kN. B. Consider the beam shown in the following figure. In this beam, there are different types of existing forces, such as applied moment, distributed load and point load. Knowing the magnitude of each of the forces,…
Hey, please reply as soon as posible Make the shear force and bending moment diagrams on Beam ABCDE. Also find the maximum values of shear force and bending moment (indicate the magnitudes of the maximum values and their location in the beam). You must justify the shape and values of the graphics you present. Consider that, in addition to the beam, there is a box with a "Weight" that is supported by the beam itself and the wall, by means of an arrangement of cables attached to the F ring. Consider the information provided on the reactions at points A and D. In the case of point A the only vertical reaction is supplied, directed downwards. important data: a = 285 m, b = 190 m, d= 380 m, e = 1995 m, f = 95 m, g = 190 m. Load in N/m, w=2,105 N/m. Weight: 200 NStrength: 50 NReaction force: D = 100 N, Ay = 50 N
In the diagram below, The raccoon has a mass of 40kg and is 5m from the hinge. The beam is 8m long and is 6kg. The cable is 2m long. The beam has a diameter of 8cm. a) What are the horizontal and vertical forces on the hinge? b) What is the shear force from the cable on the beam?
2. A ladder 12 m long leans against a vertical frictionless wall with its lower end 3 m from the wall. The ladder weighs 40 N. Find the magnitude and direction of the force exerted on the lower end of the ladder. 3. A uniform 25 N beam 6 m long is carried by two men A and B, one at each end of the beam. a) If A exerts a force of 20 N, where must a load of 45 N be placed on the beam? b) What force does B exert?
"Suppose someone with a body weight of 75 kg is lifting a box weighing 15 kg. If their back forms an angle of 70 degrees with the horizontal plane, and the distance from the object to the center of their body is 0.5 cm. The questions are as follows: 1. Create a free-body diagram for the above condition and apply the sign convention for forces and moments. 2. Calculate the magnitude of the compression force (F compression) and the shear force (F shear) generated. 3. Analyze whether this job is safe to perform."