An alloy has a yield strength of 41 ksi, a tensile strength of 57 ksi, and an elastic modulus of 16 × 106 psi. A cylindrical specimen of this alloy 0.5 in. in diameter and 10 in. long is stressed in tension and found to elongate 0.3 in. On the basis of the information given, is it possible to compute the magnitude of the load that is necessary to produce this change in length? If so, calculate the load. If not, explain why.
Learn your wayIncludes step-by-step video
Chapter 1 Solutions
Materials for Civil and Construction Engineers (4th Edition)
Additional Engineering Textbook Solutions
Foundation Design: Principles and Practices (3rd Edition)
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Starting Out with C++: Early Objects (9th Edition)
Database Concepts (8th Edition)
- A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.arrow_forwardA cube made of an alloy with dimensions of 50 mm * 50 mm * 50 mm is placed into a pressure chamber and subjected to a pressure of 90 MPa. If the modulus of elasticity of the alloy is 100 GPa and Poisson’s ratio is 0.28, what will be the length of each side of the cube, assuming that the material remains within the elastic region?arrow_forwardA cylindrical rod 600 mm long and having a diameter 13.2 mm is to be subjected to a tensile load. If the rod is to experience neither plastic deformation nor an elongation of more than 1.4 mm when the applied load is 30 KN. Which of the four metals or alloys listed below are possible candidates. Justify the answer with calculations Material modulus of elasticity(gpa) yield strength(mpa) tensile strength(mpa) Aluminium alloy 70 255 420 Brass alloy 100 345 420 Copper 110 210 275 Steel alloy 207 450 550arrow_forward
- Only attempt if you know the correct answer with all steps. A cube made of an alloy with dimensions of 2 in. X 2 in. X 2 in. is placed into a pressure chamber and subjected to a pressure of 15 ksi. If the modulus of elasticity of the alloy is 29000 ksi and Poisson's ratio is 0.30, what will be the length of each side of the cube, assuming that the material remains within the elastic region?arrow_forwardA rod made of aluminum alloy with a gauge length of 200 mm, diameter of 11mm, and yield strength of 150 MPa, was subjected to a tensile load of 5.85 kN. If the gauge length was changed to 100.10 mm and the diameter was changed to 9.9967mm, calculate the modulus of elasticity and Poison’s ratio. Are the numbers in line with standard numbers for Aluminum Alloy?arrow_forwardAn aluminum alloy cylinder with a diameter of 3 in. and a height of 6 in. is subjected to a compressive load of 50,000 pounds. Assume that the material is within the elastic region and a modulus of elasticity of 11 * 106 psi. a. What will be the lateral strain if Poisson’s ratio is 0.33? b. What will be the diameter after load application? c. What will be the height after load application?arrow_forward
- Given that a steel cylinder of dimensions 12.0 mm in diameter and 70 mm long is subjected totension.(a) Determine the modulus of elasticity in the figure below.(b) Using the figure below, calculate the deformation in the steel cylinder subjected to 15 kNtension force.arrow_forwardA tensile load of 190 kN is applied to a round metal bar with a diameter of 16 mm and a gauge length of 50 mm. Under this load, the bar elastically deforms so that the gauge length increases to 50.1349 mm and the diameter decreases to 15.99 mm. Determine the modulus of elasticity and Poisson’s ratio for this metal.arrow_forward2. A rigid steel container is partially filled with a liquid at 15 atm. The volume of the liquid is 1.23200 L. At a pressure of 30 atm, the volume of the liquid is 1.23100 L. Find the average bulk modulus of elasticity of the liquid over that given range of pressure if the temperature after compression is allowed to return to its initial value. What is the coefficient of compressibility (β)?arrow_forward
- A cylindrical rod with a radius of 0.3 in. and a length of 15 in. is subjected to a tensile load. If the rod is to experience neither plastic deformation nor an elongation of more than 0.018 in. when the applied load is 7,000 lb, which of the four metals or alloys listed below are possible candidates? Justify your choice(s).arrow_forwardA force of 100,000 N is applied to an iron bar with a cross-sectional area of 10 mm × 20mm and having a yield strength of 400 MPa and a tensile strength of 480 MPa,Determinea. whether the bar will plastically deform; andb. whether the bar will experience neckingarrow_forwardA wood beam is strengthened using two steel plates as shown in the figure below. *Inserted Photo* The beam has simple supports and an overhang and is subjected to a point load and a uniform load as shown in the figure below. Calculate the maximum tensile and compressive stresses of the beam. Assume that Ew = 11 GPa and Es = 200 GPa. (Enter your answers in MPa. Use the deformation sign convention.) maximum tensile stress in wood ? MPa maximum tensile stress in steel ? MPa maximum compressive stress in wood ? MPa maximum compressive stress in steel ? MPaarrow_forward
- Engineering Fundamentals: An Introduction to Engi...Civil EngineeringISBN:9781305084766Author:Saeed MoaveniPublisher:Cengage LearningSteel Design (Activate Learning with these NEW ti...Civil EngineeringISBN:9781337094740Author:Segui, William T.Publisher:Cengage LearningMaterials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage Learning