SHIGLEY'S MECH.ENGIN....(LOOSE)>CUSTOM<
SHIGLEY'S MECH.ENGIN....(LOOSE)>CUSTOM<
10th Edition
ISBN: 9781260163155
Author: BUDYNAS
Publisher: MCG CUSTOM
bartleby

Concept explainers

bartleby

Videos

Textbook Question
Chapter 1, Problem 12P

A solid circular rod of diameter d undergoes a bending moment M = 1000 Ibf · in inducing a stress σ = 32M/(πd3). Using a material strength of 25 kpsi and a design factor of 2.5. determine the minimum diameter of the rod. Using Table A-17 select a preferred fractional diameter and determine the resulting factor of safety.

Blurred answer
Students have asked these similar questions
Mechanical design The maximum load in a rotating shaft is subjected to bending moment of 1 kN.m and a torque of 1 kN.m. The member is made of steel the Ultimate Tensile Strength 440 MPa, Yield Tensile Strength 370 MPa. With a safety factor of 4, kt = km = 1.5 and keyway stress consternation is presented. According to the maximum shear stress theory, the shaft diameter will be: a. 160 mm b. 74 mm C. 145 mm d. 92.5 mm e. 60 mm f. 66 mm
A solid circular rod of diameter d undergoes a bending moment M = 113 Nm inducing a stress σ = 16M/ (πd3). Using a material strength of 172.4 MN/m2 and a design factor of 2.5, determine the minimum diameter of the rod. Using Table 1, select a preferred fractional diameter and determine the resulting factor of safety
1) A flange coupling connects two 50mm shafts. The flanges are fitted with 4 bolts of SAE1040 steel on an 80mm bolt circle. The shaft runs @ 360 rpm & transmits 30kW. Assume a factor of safety 4, ultimate tension of 490x103 kPa; ultimate shear of 400x103 kPa, determine: (a) the torque transmitted in kN-m; (b) the minimum diameter of the bolts required based on commercial sizes; (c) the minimum thickness of the flange.

Chapter 1 Solutions

SHIGLEY'S MECH.ENGIN....(LOOSE)>CUSTOM<

Knowledge Booster
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
  • A steel rod is subjected to a reversed axial load of 180 kN. Find the diameter of the rod for a factor of safety of 2. Neglect column action. The material has an ultimate tensile strength of 1070 MPa and yield strength of 910 MPa. The endurance limit in reversed bending may be assumed to be one-half of the ultimate tensile strength. Other correction factors may be taken as follows: For axial loading (Ka) = 0.7; For machined surface (Ksur) = 0.8 ; For size (Ksz) = 0.85 ; For stress concentration(Kf)= 1.0.3.
    A 2.5 cm x 7.5 cm steel beam with a length of 61 cm is subjected to a reversed load of 17.8 kN at midpoint. If yield stress and endurance stress are 410 MPa and 155 MPa respectively, what should be the minimum factor of safety? A helical spring has a free length of 203 mm, outside diameter of 115 mm and a wire diameter of 13 mm. It consist of 9.5 coils squared and grounded at the ends. If it is compressed to its solid length, what is the stress in the spring? Let G = 80 GPa.
    The material is a spring wire has a shear modulus of 1.2 x 107 lbf/in2. The maximum allowable stress under design conditions is 50,000 lbf/in2. The spring index is 7. Assume the maximum stress is experienced when a 700 lbm object falls from a height of 46 in above the tip of the spring, impacts squarely on the spring, and deflects the spring 10 in. Determie:1. The minimum wire diameter is most nearlyA. 0.58 in B. 0.88 in C. 1.4 in D. 1.8 in2. The mean coil diameter is most nearlyA. 8.6 in B. 10 in C. 13 in D. 16 in3. The number of active coils is most nearlyA. 8 B. 11 C. 12 D. 14
  • The material is a spring wire has a shear modulus of 1.2 x 107 lbf/in2. The maximum allowable stress under design conditions is 50,000 lbf/in2. The spring index is 7. Assume the maximum stress is experienced when a 700 lbm objects falls from a height of 46 in above the tip of the spring, impacts squarely on the spring, and deflects the spring 10 in. Determie: 1. The minimum wire diameter is most nearly A. 0.58 in B. 0.88 in C. 1.4 in D. 1.8 in 2. The mean coil diameter is most nearly A. 8.6 in B. 10 in C. 13 in D. 16 in 3. The number of active coils is most nearly A. 8 B. 11 C. 12 D. 14
    A semi-elliptic spring used for automobile suspension, consists of two extra full-length leaves and eight graduated-length leaves, including the master leaf. The centre-to centre distance between the two eyes is 1 m. The leaves are made of steel 55Si2Mo90 (Syt = 1500 N/mm2and E = 207000 N/mm2) and the factor of safety is 2. The maximum spring load is 30 kN. The leaves are pre- stressed so as to equalize stresses in all leaves under maximum load. Determine the dimensions of the cross-section of the leaves and the deflection at the end of the spring.
    The shaft and the flange of a marine engine are to be designed for flange coupling, in which the flange is forged on the end of the shaft. The following particulars are to be considered in the design: Power of the engine=2.4 MW Speed of the engine 80 r.p.m Permissible shear stress in bolts and shaft = 60 MPa Number of bolts used =6 Pitch circle diameter of bolts=1.6* Dimeter of shaft Find 1.diameter of shaft; 2.diameter of bolts; 3.thickness of flange; and 4.diameter of flange. (25 degrea
    • SEE MORE QUESTIONS
    Recommended textbooks for you
  • Mechanics of Materials (MindTap Course List)
    Mechanical Engineering
    ISBN:9781337093347
    Author:Barry J. Goodno, James M. Gere
    Publisher:Cengage Learning
  • Mechanics of Materials (MindTap Course List)
    Mechanical Engineering
    ISBN:9781337093347
    Author:Barry J. Goodno, James M. Gere
    Publisher:Cengage Learning
    Column buckling; Author: Amber Book;https://www.youtube.com/watch?v=AvvaCi_Nn94;License: Standard Youtube License