MECHANICAL ENGINEERING DES.(LL)-W/CNCT
15th Edition
ISBN: 9781260531374
Author: BUDYNAS
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 1, Problem 12P
A solid circular rod of diameter d undergoes a bending moment M = 1000 Ibf · in inducing a stress σ = 32M/(πd3). Using a material strength of 25 kpsi and a design factor of 2.5. determine the minimum diameter of the rod. Using Table A-17 select a preferred fractional diameter and determine the resulting factor of safety.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Mechanical design
The maximum load in a rotating shaft is subjected to bending moment of 1 kN.m and a torque of 1 kN.m. The member is made of steel the Ultimate Tensile Strength 440 MPa, Yield Tensile Strength 370 MPa. With a safety factor of 4, kt = km = 1.5 and keyway stress consternation is presented. According to the maximum shear stress theory, the shaft diameter will be:
a. 160 mm
b. 74 mm
C. 145 mm
d. 92.5 mm
e. 60 mm
f. 66 mm
A solid circular rod of diameter d undergoes a bending moment M = 113 Nm inducing a stress σ = 16M/ (πd3). Using a material strength of 172.4 MN/m2 and a design factor of 2.5, determine the minimum diameter of the rod. Using Table 1, select a preferred fractional diameter and determine the resulting factor of safety
1) A flange coupling connects two 50mm shafts. The flanges are fitted with 4 bolts of SAE1040 steel
on an 80mm bolt circle. The shaft runs @ 360 rpm & transmits 30kW. Assume a factor of safety 4,
ultimate tension of 490x103
kPa; ultimate shear of 400x103
kPa, determine:
(a) the torque transmitted in kN-m;
(b) the minimum diameter of the bolts required based on commercial sizes;
(c) the minimum thickness of the flange.
Chapter 1 Solutions
MECHANICAL ENGINEERING DES.(LL)-W/CNCT
Ch. 1 - Select a mechanical component from Part 3 of this...Ch. 1 - Select a mechanical component from Part 3 of this...Ch. 1 - Select an organization listed in Sec. 16, go to...Ch. 1 - Go to the Internet and connect to the NSPE website...Ch. 1 - Go to the Internet and connect to the NSPE website...Ch. 1 - Estimate how many times more expensive it is to...Ch. 1 - The costs to manufacture a part using methods A...Ch. 1 - A cylindrical part of diameter d is loaded by an...Ch. 1 - When one knows the true values x1 and x2 and has...Ch. 1 - Use the true values x1 = 7 and x2 = 8 (a)...
Ch. 1 - A solid circular rod of diameter d undergoes a...Ch. 1 - A fatigue test is performed on rotating beam...Ch. 1 - Determinations of the ultimate tensile strength...Ch. 1 - The lives of parts are often expressed as the...Ch. 1 - The tensile 0.2 percent offset yield strength of...Ch. 1 - A mechanical system comprises three subsystems in...Ch. 1 - From See. 3-12, the maximum shear stress in a...Ch. 1 - A round cold-drawn 1045 steel rod has a mean...Ch. 1 - A beam subjected to axial loading will experience...Ch. 1 - Three blocks A, B, and C and a grooved block D...Ch. 1 - The volume of a rectangular parallelepiped is...Ch. 1 - A pivot in a linkage has a pin in the figure whose...Ch. 1 - A circular cross section O ring has the dimensions...Ch. 1 - Prob. 25PCh. 1 - Prob. 26PCh. 1 - Prob. 27PCh. 1 - Prob. 28PCh. 1 - Convert the following to appropriate ips units:...Ch. 1 - Convert the following to appropriate SI units: (a)...Ch. 1 - Generally, final design results are rounded to or...Ch. 1 - Repeal Prob. 1-31 for the following: (a) = F/wt,...Ch. 1 - Repeat Prob. 131 for: (a) = F/A, where A = d2/4, F...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A pinned-end strut of aluminum (E = 10,400 ksi) with a length L = 6 ft is constructed of circular tubing with an outside diameter d = 1 in. (sec figure). The strut must resist an axial load F = 4 kips with a factor of safety n = 2.0 with respect to the critical load. Determine the required thickness t of the tube.arrow_forwardA pinned-end strut of a length L = 5.2 ft is constructed of steel pipe (E = 30 × 103 ksi) having an inside diameter d1= 2.0 in. and outside diameter d2= 2.2 in. (sec figure). A compressive load F = 2.0 kips is applied with eccentricity e = 1.0 in. What is the maximum compressive stress max in the strut? What is the allowable load Pallowif a factor of safety n = 2 with respect to yielding is required? (Assume that the yield stress y of the steel is 42 ksi.)arrow_forwardRepeat Problem 11.2-14 using L = 12 ft, ß = 0.25 kips/in., ßRl= 1.5ßL2, and ßR2= 2 ßR1.arrow_forward
- A steel rod is subjected to a reversed axial load of 180 kN. Find the diameter of the rod for a factor of safety of 2. Neglect column action. The material has an ultimate tensile strength of 1070 MPa and yield strength of 910 MPa. The endurance limit in reversed bending may be assumed to be one-half of the ultimate tensile strength. Other correction factors may be taken as follows: For axial loading (Ka) = 0.7; For machined surface (Ksur) = 0.8 ; For size (Ksz) = 0.85 ; For stress concentration(Kf)= 1.0.3.arrow_forwardA 2.5 cm x 7.5 cm steel beam with a length of 61 cm is subjected to a reversed load of 17.8 kN at midpoint. If yield stress and endurance stress are 410 MPa and 155 MPa respectively, what should be the minimum factor of safety? A helical spring has a free length of 203 mm, outside diameter of 115 mm and a wire diameter of 13 mm. It consist of 9.5 coils squared and grounded at the ends. If it is compressed to its solid length, what is the stress in the spring? Let G = 80 GPa.arrow_forwardThe material is a spring wire has a shear modulus of 1.2 x 107 lbf/in2. The maximum allowable stress under design conditions is 50,000 lbf/in2. The spring index is 7. Assume the maximum stress is experienced when a 700 lbm object falls from a height of 46 in above the tip of the spring, impacts squarely on the spring, and deflects the spring 10 in. Determie:1. The minimum wire diameter is most nearlyA. 0.58 in B. 0.88 in C. 1.4 in D. 1.8 in2. The mean coil diameter is most nearlyA. 8.6 in B. 10 in C. 13 in D. 16 in3. The number of active coils is most nearlyA. 8 B. 11 C. 12 D. 14arrow_forward
- Prob # 1.A round bar made from SAE 1025 low Carbon steel is to support a direct tension load of 50,000 lbs. Using a factor of safety of 4, and assuming that the stress concentration factor, k = 1, What is the suitable standard diameter. Yield stress is 40,000 psi. a. 3 ½ inch b. 2 ¼ inch c. 2 9/16 inch d. 1 ½ incharrow_forwardA steel rod of diameter D = 50 mm has a tensile yield strength of 345 MPa supports an axial load P = 50 kN and a vertical load R = 2 kN acting at the end of an 0.8 m long arm. Calculate the strength factor of safety using (a) the maximum normal stress theory, (b) the maximum shear stress theory and (c) the distortion energy theory.arrow_forwardCalculate the elongation of a solid steel shaft of SAE 1030 carbon steel 2 7/8 inches in diameter by 5 ft in length supporting a direct tension load of 60.000 lbs. The factor of safety is set at 4, stress concentration factor k = 1, and yield strength of 40.000 psi. 0.0996 0.0185 0.0235 0.1886arrow_forward
- The material is a spring wire has a shear modulus of 1.2 x 107 lbf/in2. The maximum allowable stress under design conditions is 50,000 lbf/in2. The spring index is 7. Assume the maximum stress is experienced when a 700 lbm objects falls from a height of 46 in above the tip of the spring, impacts squarely on the spring, and deflects the spring 10 in. Determie: 1. The minimum wire diameter is most nearly A. 0.58 in B. 0.88 in C. 1.4 in D. 1.8 in 2. The mean coil diameter is most nearly A. 8.6 in B. 10 in C. 13 in D. 16 in 3. The number of active coils is most nearly A. 8 B. 11 C. 12 D. 14arrow_forwardA semi-elliptic spring used for automobile suspension, consists of two extra full-length leaves and eight graduated-length leaves, including the master leaf. The centre-to centre distance between the two eyes is 1 m. The leaves are made of steel 55Si2Mo90 (Syt = 1500 N/mm2and E = 207000 N/mm2) and the factor of safety is 2. The maximum spring load is 30 kN. The leaves are pre- stressed so as to equalize stresses in all leaves under maximum load. Determine the dimensions of the cross-section of the leaves and the deflection at the end of the spring.arrow_forwardThe shaft and the flange of a marine engine are to be designed for flange coupling, in which the flange is forged on the end of the shaft. The following particulars are to be considered in the design: Power of the engine=2.4 MW Speed of the engine 80 r.p.m Permissible shear stress in bolts and shaft = 60 MPa Number of bolts used =6 Pitch circle diameter of bolts=1.6* Dimeter of shaft Find 1.diameter of shaft; 2.diameter of bolts; 3.thickness of flange; and 4.diameter of flange. (25 degreaarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Column buckling; Author: Amber Book;https://www.youtube.com/watch?v=AvvaCi_Nn94;License: Standard Youtube License