Theory and Design for Mechanical Measurements
6th Edition
ISBN: 9781118881279
Author: Richard S. Figliola, Donald E. Beasley
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 1, Problem 1.35P
The acceleration of a cart down a plane inclined at an angle a to horizontal can be determined by measuring the change in speed of the cart at two points, separated by a distance s, along the inclined plane. Suppose two photocells are fixed at the two points along the plane. Each photocell measures the time for the cart, which has a length L, to pass it. Identify the important variables in this test. List any assumptions that you feel are intrinsic to such a test. Suggest a concomitant approach. How would you interpret the data to answer the question?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Wind blows and pasts a banner causes it to flutter. The fluttering frequency f is a function of the wind speed V, the air density ρ, the acceleration of gravity g, the length of the banner L and the “area density” of the flag material ρA (with dimensions of ML-2 ). In order to estimate the flutter frequency of a large banner with L = 40 ft in a V = 30 ft/s wind, a small banner with L = 4 ft is to be tested in a wind tunnel.
(a) What is the area density of the small banner when the large banner has area density of 0.006 slugs/ft2?
(b) What should the wind tunnel velocity be to test the small model?
(c) It has been shown that the small banner flutters at 6 s-1 when the same area density and wind tunnel velocity are used in parts (a) and (b). In this case, what is the fluttering frequency of the large banner?
Pressure distribution measurements are made on a two-dimensional wing model placed in a wind tunnel. The difference between the static pressure sockets on the surface and the static pressure of the free stream is measured. 30 data is taken at each measurement point. The average of the values measured from one of the sockets near the trailing edge was calculated as 2.30 Pa, and the standard deviation was calculated as 2.65 Pa. After applying the Chauvenet criterion to these measurement values, it was decided to eliminate 3 measurements and the new mean value was found to be 2.18 Pa and the standard deviation was 2.42. It was verified that the unexcluded data fit the normal distribution curve. Data above how many Pa and below how many Pa were eliminated? Estimate how many data have negative value (?<0) after elimination.
The pressure difference ∆p produced by a water pump, and the power P required to operate it, each depend on the size of the pump, measured by the diameter D of the impeller, the volume flow rate ˙q, the rate of rotation ω, the water density ρ and dynamic viscosity µ. (a) Express the non-dimensional pressure difference and power as separate functions of the other non-dimensional groups. (b) Tests on a model pump are performed at 0.5 × full scale, at a rotation rate that is 2 × the full-scale value. To achieve dynamic similarity in the model test: (i) what would the volume flow rate of the water need to be in the model test compared to the full-scale? (ii) What would the pressure difference be compared to the full scale? (iii) What would the power consumption be relative to the full scale?
Chapter 1 Solutions
Theory and Design for Mechanical Measurements
Ch. 1 - Prob. 1.1PCh. 1 - Prob. 1.2PCh. 1 - Prob. 1.3PCh. 1 - Prob. 1.4PCh. 1 - Prob. 1.5PCh. 1 - Discuss how the resolution of the display scale of...Ch. 1 - Prob. 1.7PCh. 1 - Prob. 1.8PCh. 1 - Prob. 1.9PCh. 1 - Prob. 1.10P
Ch. 1 - State the purpose of using randomization methods...Ch. 1 - Provide an example of repetition and replication...Ch. 1 - Develop a test plan that might be used to estimate...Ch. 1 - Develop a test plan that might be used to evaluate...Ch. 1 - A race engine shop has just completed two engines...Ch. 1 - A thermodynamics model assumes that a particular...Ch. 1 - Regarding the Mars Climate Orbiter spacecraft...Ch. 1 - A large batch of carefully made machine shafts can...Ch. 1 - Suggest an approach or approaches to estimate the...Ch. 1 - Suggest a test matrix to evaluate the wear...Ch. 1 - Figure 1.15 Orifice flow meter setup used for...Ch. 1 - The sale of motor fuel is an essential business in...Ch. 1 - Using either the ASME 19.5 or ISO 5167 test...Ch. 1 - A simple thermocouple circuit is formed using two...Ch. 1 - 1.25 A linear variable displacement transducer...Ch. 1 - For the LVDT calibration of the previous problem,...Ch. 1 - A manufacturer wants to quantify the expected...Ch. 1 - Prob. 1.28PCh. 1 - As described in a preceding problem, the...Ch. 1 - Light gates may be used to measure the speed of...Ch. 1 - You estimate your car’s fuel use by recording...Ch. 1 - When discussing concomitant methods, we used the...Ch. 1 - Prob. 1.33PCh. 1 - For the strain gauge calibration of the previous...Ch. 1 - The acceleration of a cart down a plane inclined...Ch. 1 - In general, what is meant by the term “standard”?...Ch. 1 - A common scenario: An engineer has two pencil-...Ch. 1 - Explain the potential differences in the following...Ch. 1 - Research the following test standards and codes....Ch. 1 - A hotel chain based in the United States contracts...Ch. 1 - Test code ASTM 558-13 allows for the comparison of...Ch. 1 - Suggest a reasonable number of significant digits...Ch. 1 - Using spreadsheet software (such as Microsoft...Ch. 1 - Prob. 1.44PCh. 1 - Round the following numbers to 3 significant...Ch. 1 - Express the result, rounding to an appropriate num...Ch. 1 - Express the result by rounding to an appropriate...Ch. 1 - A car’s speed is determined by the time it takes...Ch. 1 - How much error could you tolerate in (1) book...Ch. 1 - Apply the guidelines to determine the number of...Ch. 1 - Using a tape measure having 1 mm graduations, the...Ch. 1 - Show how the following functions can be...Ch. 1 - Prob. 1.53PCh. 1 - For the calibration data of Table 1.5, determine...Ch. 1 - Prob. 1.55PCh. 1 - Each of the following equations can be represented...Ch. 1 - Plot y = 10e“° 5x volts on in semilog format (use...Ch. 1 - Prob. 1.58PCh. 1 - Prob. 1.59P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A ship 350 m long moves in sea water whose density is 1030 kg/m3 . A 1:120 model of this ship is to be tested in a wind tunnel. The velocity of the wind tunnel around the model is 35 m/s and the resistance of the model is 65 N. Determine the velocity and also the resistance of the ship in sea water. The density of air is given as 1.24 kg/m3 . Take the kinematic viscosity of air and sea water as 0.012 stokes and 0.018 stokes respectively.arrow_forwardTo measure the density of a stone, a digital scale and a beaker cup filled with water are used. The balance is used to measure the mass of the stone, while the beaker is used to measure the volume of the stone. It is known that the digital balance has a resolution of 0.1 g and that the beaker cup has a resolution of 5 ml. Repeated mass measurements return the following values: 250.0 g; 249.9 g; 250.3 g; 249.6g; 250.1 g; 249.7g; 250.4 g; 250.0 g; 248.8 g; 250.2 g The volume is measured only once. Placing the stone in the beaker, a volume of displaced water equal to 50 ml is measured. Using a k=2.5, check if the density of the stone is compatible or out of line with the value ρ = (4910 ± 65) kg.m-3 (a) none of the above (b) the values are compatible (c) missing data to perform the compatibility test (d) the values are discrepantarrow_forwardA cheap accelerometer, probably worth the price, can bemade from a U-tube as in Fig. . If L = 18 cm andD = 5 mm, what will h be if a x = 6 m/s 2 ? Can the scalemarkings on the tube be linear multiples of a x ?arrow_forward
- Discuss the importance of measuring devices for Electric Motor and Internal Combustion Engine in terms of accuracy.arrow_forwardCardiologists use the short-range scaling exponent α1, which measures the randomness of heart rate patterns, as a tool to assess risk of heart attack. The article “Applying Fractal Analysis to Short Sets of Heart Rate Variability Data” compared values of α1 computed from long series of measurements (approximately 40,000 heartbeats) with those estimated from the first 300 beats to determine how well the long-term measurement (y) could be predicted the short-term one (x). Following are the data (obtained by digitizing a graph). Short Long 0.54 0.55 1.02 0.79 1.4 0.81 0.88 0.9 1.68 1.05 1.16 1.05 0.82 1.05 0.93 1.07 1.26 1.1 1.18 1.19 0.81 1.19 0.81 1.2 1.28 1.23 1.18 1.23 0.71 1.24 Note: This problem has a reduced data set for ease of performing the calculations required. This differs from the data set given for this problem in the text. Compute the least-squares line for predicting the long-term measurement from the short-term measurement.…arrow_forwardApplying principles of dynamics A usual football tryout involves a player running a 40-yard dash. If a particular player finishes the dash in 4.25 seconds while reaching his maximum speed at the first 16 yard mark with a constant acceleration and then maintains that speed for the remainder of the run, determine this person’s acceleration over the first 16 yard, his maximum speed and how long he accelerated. SET YOUR OWN VARIABLES AS YOU SEE FIT.arrow_forward
- The drag force on an airship must be determined by testing with a reduced-scale model. The tests are carried out in a water tunnel, where the airship model is fixed to a support instrumented with a force sensor. The speed of the flow that affects the model is controlled by a variable speed pump that is the one that originates the flow towards the model. The scale is 1:20, μwater=1.01x10-3 kg/ms, μair= 1.85x10-5 Pa-s, ρair= 1.25kg/m3, ρwater=1000 kg/m3. Determine: a) the dimensionless numbers of the situation b) The VM if VP=36km/h c) The power of the prototype airship if FM= 1 649 N.arrow_forwardPierce (1948) mechanically measured the frequency (the number of wing vibrations per second) of chirps (or pulses of sound) made by a striped ground cricket, at various ground temperatures. Since crickets are ectotherms (cold-blooded), the rate of their philosophical processes and their overall metabolism are influenced by temperature. Consequently, there is a reason to believe that temperature would have a profound affect on aspects of their behavior, such as chirp frequency. In general, it was found that crickets did not sing at temperatures colder than 60°F or warmer than 100°F. In the following data let X= chirps/sec for the striped ground cricket and Y= temperature in degrees of Fahrenheit. X 19 19.8 18.4 17.1 15.5 14.7 17.1 15.4 16.2 15 17.2 16 17 14.4 Y 71.6 93.3 84.3 80.6 75.2 69.7 82 69.4 83.3 79.6 82.6 80.6 83.5 76.3 a. use two decimal places: Y bar =? b. use two decimal…arrow_forward1.The thickness of a gage block is measured five times using an instrument that has a resolution of 0.001 cm. The following measurements are obtained (in cm): 1.100, 1.110, 1.090, 1.095, and 1.105. The true gauge block thickness is known to be 1.050 cm. Use this information to answer the following questions: a. What errors or sources of measurement error can be identified in the example? (Hint: there are three). Identify each one as a random or systematic uncertainty. b. Estimate the magnitudes of each of these uncertainties. Wherever possible, estimate random uncertainties at a 95% probability/confidence level. c. Based on the uncertainties determined in part b, estimate the overall uncertainty of a measurement obtained by this instrument.arrow_forward
- An automotive engineer is testing how quickly a newly designed sports car accelerates from rest. He has collected data giving the velocity V, in miles per hour, as a function of time t, in seconds, since the car was at rest. Below is a table giving a portion of his data. Time (t) Velocity (V) 2.0 28.4 2.5 33.9 3.0 39.4 3.5 44.9 (a) By calculating differences, show that the data in this table can be modeled by a linear function. Time 2.0 to 2.5 2.5 to 3.0 3.0 to 3.5 Change in t Change in V (b) What is the slope for the linear function modeling velocity as a function of time? mph per secExplain in practical terms the meaning of the slope. This means that, after every second, the car will be going miles per hour faster. This says that the acceleration is ---Select--- varying constant . (c) Use the data in the table to find the formula for velocity V as a linear function of time t that is valid over the time period covered in the table.V =…arrow_forwardIn the field of air pollution control, one often needs to sample the quality of a moving airstream. In such measurements a sampling probe is aligned with the flow as sketched in Fig. A suction pump draws air through the probe at volume flow rate V· as sketched. For accurate sampling, the air speed through the probe should be the same as that of the airstream (isokinetic sampling). However, if the applied suction is too large, as sketched in Fig, the air speed through the probe is greater than that of the airstream (super iso kinetic sampling). For simplicity consider a two-dimensional case in which the sampling probe height is h = 4.58 mm and its width is W = 39.5 mm. The values of the stream function corresponding to the lower and upper dividing streamlines are ?l = 0.093 m2/s and ?u = 0.150 m2/s, respectively. Calculate the volume flow rate through the probe (in units of m3/s) and the average speed of the air sucked through the probe.arrow_forwardWhat is an example of experimental uncertainty?arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Unit Conversion the Easy Way (Dimensional Analysis); Author: ketzbook;https://www.youtube.com/watch?v=HRe1mire4Gc;License: Standard YouTube License, CC-BY