Heating Ventilating and Air Conditioning: Analysis and Design
6th Edition
ISBN: 9780471470151
Author: Faye C. McQuiston, Jeffrey D. Spitler, Jerald D. Parker
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 1, Problem 1.3P
A pump develops a total head of 50 ft of water under a given operating condition. What pressure is the pump developing in SI units and terminology?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
If a pump is capable of lifting 5000kg of water through a vertical height of 60m in 15 min, the power of the pump is
What is the horsepower requirement for a water pump, if the required flow rate is 200 gpm and the required pressure increase assigned to the pump is 32 psi?
2.
A pump draws water from a lake delivered to a height of 50 meters above the lake and encounters 15 meters of headloss. Determine the pump power requirement in Kilo-Watts to deliver a constant supply of 500 Liters per second?
The correct answer has a margin of 1 from exact answer. Velocity head is neglected.
Chapter 1 Solutions
Heating Ventilating and Air Conditioning: Analysis and Design
Ch. 1 - Convert the following quantities from English to...Ch. 1 - Convert the following quantities from SI to...Ch. 1 - A pump develops a total head of 50 ft of water...Ch. 1 - A fan is observed to operate with a pressure...Ch. 1 - The electric utility rate for a facility during...Ch. 1 - For the business whose monthly electrical energy...Ch. 1 - Detmine the interest rate at which the project in...Ch. 1 - How much could a company afford to spend on an...Ch. 1 - Make the following volume and mass flow rate...Ch. 1 - A room with dimensions of 31020m is estimated to...
Ch. 1 - Compute the heat transferred from water as it...Ch. 1 - Air enters a heat exchanger at a rate of 5000...Ch. 1 - Water flowing at a rate of 1.5 kg/s through a heat...Ch. 1 - Air at a mean temperature of 50 F flows over a...Ch. 1 - Repeat Problem 1-10 for air at 10 C, a tube with...Ch. 1 - Air at 1 atm and 76 F is flowing at the rate of...Ch. 1 - Air flowing at the rate of 1000 cfm and with a...Ch. 1 - A chiller is providing 5 tons of cooling to an air...Ch. 1 - Air is delivered to a room at 58 F and the same...Ch. 1 - A chiller is to pro;ide 12 tons of cooling to a...Ch. 1 - Air is being rnished to a 30-ft by 40-ft by 12-ft...Ch. 1 - If cold outside air at 20 F is leaking into a...Ch. 1 - A Btu-meter is a device that measures water flow...Ch. 1 - A heat pump uses a 100,000-gallon swimming pool as...Ch. 1 - A heat pump uses a 100,000-gallon swimming pooi as...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
2.15 Compute the rectangular components parallel and perpendicular to the inclined planes shown.
Applied Statics and Strength of Materials (6th Edition)
The volumetric flow rate and discharge velocity of the air.
Introduction to Heat Transfer
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
1.1 What is the difference between an atom and a molecule? A molecule and a crystal?
Manufacturing Engineering & Technology
Comprehension Check 7-15
Indicate whether the following equation is dimensionally consistent (yes or no):
wh...
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
The 2-Mg truck is traveling at 15 m/s when the brakes on all its wheels are applied, causing it to skid for a d...
Engineering Mechanics: Dynamics (14th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
Variable displacement pumps used in hydraulic applications can
arrow_forward
The head lost from point 1 to point 2 is 4m. If the specific gravity of mercury is 13.6, determine The velocity at point 1 in m/s and the maximum height the water can reach “hm” if neglecting air friction in m
arrow_forward
A pump is delivering 160 liters per second of water using an impeller diameter of 254mm and operating at a speed of 1800 rpm. If the speed is held constant and the impeller diameter is changed to 203.2 mm, what is the new discharged of the pump in liters per second?(128 L/s)
arrow_forward
It is required to pump water at 100 gal/min from a large reservoir to the surface of another reservoir 400 feet higher. What is the horsepower of the motor to drive the pump if the efficiency of the pump is 70%?
arrow_forward
If a pumped hydro installation can hold 30 million m3 of water, and the water head is 36 m:
a)Determine the energy content of the installation.
b)If the reservoir normally empties within eight hours and fifty-two minutes and the efficiency of the turbine is 67%, calculate the output power of the installation.
Calculate the total pressure that the turbine is experiencing
arrow_forward
For a centrifugal pump of impeller diameter D rotating at N to develop a head of H and discharge Q, what would be the new head developed by the same pump if we halve the impeller speed to N/2?
H/A
2H
H
4H
H/2
arrow_forward
A turbine develops 144 HP running at 100 rpm under a head of 7.7 meters. After resolving the turbine speed, what horsepower would be developed under a head of 11 meters?
arrow_forward
What is the power ratio of a pump to its 1/5 scale model if the ratio of the heads is 4 to 1?
arrow_forward
If the velocity of water is 8m/s and the pressure is 140 kPa on the discharge side of a pump,
What will be the head of the pump if the velocity is 4 m/s and the pressure is 90 kPa on the suction side of the pump?
How much power is required to drive it if the diameter of suction side is 600 mm?
If the pump is rated at 120 hp, what is the efficiency of the pump neglecting energy losses in the system?
arrow_forward
A fan when driven by a 5.8 Hp motor at a speed of 800 rpm delivers 510 m3/min at a total pressure of 5 cm water gage. If in the same installation, 6.5 cm water gage pressure is required. What power will the fan be driven?
arrow_forward
A pump is required to deliver 120000 lpm of water at a head of 25 m. A motor which spins at 450 rpm is available. What kind of pump geometry should be used? Estimate the power requirement of this pump.
arrow_forward
The pressure gage leading to the turbine casing of a Francis turbine reads 0.5 MPa and the center of the spiral casing is 5 m above the tailrace. What is the net head if the velocity of the water entering the turbine is 10 m/s?
arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license