Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)
8th Edition
ISBN: 9781305387102
Author: Kreith, Frank; Manglik, Raj M.
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 1, Problem 1.45P
An electronic device that internally generates 600 mW of heat has a maximum permissible operating temperature of
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
A 2 m X 1.5 m section of wall of an industrial furnace burning gas is not insulated, and the temperature at the outer surface of this section is measured to be 80oC. The temperature of the furnace room is 30oC, and the combined convection and radiation heat transfer coefficient at the surface of the outer furnace is 10 w/oC. It is proposed to insulate this section of the furnace wall with glass wool insulation (K=0.038 W/moC) in order to reduce the heat loss by 90 percent. Assuming the outer surface temperature of the section remains at about 80oC, determine i) the thickness of the insulation that is needed and ii) the outer surface temperature of the insulation after installation.
A hot surface at 100°C is to be cooled by attaching 3-cm-long, 0.25-cm-diameter aluminum pin fins (k = 237 W/m·K) to it, with a center-to-center distance of 0.6 cm. The temperature of the surrounding medium is 30°C, and the heat transfer coefficient on the surfaces is 35 W/m2 ·K. Determine the rate of heat transfer from the surface for a 1-m x 1-m section of the plate. Also determine the overall effectiveness of the fins.
A 2-m x 1.8-m section of wall of an industrial furnace burning natural gas is not insulated, and the temperature at the outer surface of this section is measured to be 80°C. The temperature of the furnace room is 30°C, and the combined convection and radiation heat transfer coefficient at the surface of the outer furnace is 10 W/m² • °C. It is proposed to insulate this section of the furnace wall with expanded perlite insulation (k = 0.052 W/m • °C) in order to reduce the heat loss by 90%. Assuming the outer surface temperature of the metal section still remains at about 80°C, determine the thickness of the insulation that needs to be used.
ANSWER:_______cm
Chapter 1 Solutions
Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)
Ch. 1 - 1.1 On a cold winter day, the outer surface of a...Ch. 1 - 1.2 The weight of the insulation in a spacecraft...Ch. 1 - 1.3 A furnace wall is to be constructed of brick...Ch. 1 - 1.4 To measure thermal conductivity, two similar...Ch. 1 - To determine the thermal conductivity of a...Ch. 1 - A square silicon chip 7mm7mm in size and 0.5-mm...Ch. 1 - A cooling system is to be designed for a food...Ch. 1 - 1.80 Describe and compare the modes of heat loss...Ch. 1 - Heat is transferred at a rate of 0.1 kW through...Ch. 1 - 1.10 A heat flux meter at the outer (cold) wall of...
Ch. 1 - 1.11 Calculate the heat loss through a glass...Ch. 1 - 1.12 A wall with a thickness is made of a...Ch. 1 - 1.13 If the outer air temperature in Problem is...Ch. 1 - Using Table 1.4 as a guide, prepare a similar...Ch. 1 - 1.15 A thermocouple (0.8-mm-diameter wire) used to...Ch. 1 - Water at a temperature of 77C is to be evaporated...Ch. 1 - The heat transfer rate from hot air by convection...Ch. 1 - The heat transfer coefficient for a gas flowing...Ch. 1 - 1.19 A cryogenic fluid is stored in a...Ch. 1 - A high-speed computer is located in a...Ch. 1 - 1.21 In an experimental set up in a laboratory, a...Ch. 1 - 1.22 In order to prevent frostbite to skiers on...Ch. 1 - Using the information in Problem 1.22, estimate...Ch. 1 - Two large parallel plates with surface conditions...Ch. 1 - 1.25 A spherical vessel, 0.3 m in diameter, is...Ch. 1 - 1.26 Repeat Problem 1.25 but assume that the...Ch. 1 - Determine the rate of radiant heat emission in...Ch. 1 - 1.28 The sun has a radius of and approximates a...Ch. 1 - 1.29 A spherical interplanetary probe with a 30-cm...Ch. 1 - A spherical communications satellite, 2 m in...Ch. 1 - A long wire 0.7 mm in diameter with an emissivity...Ch. 1 - Wearing layers of clothing in cold weather is...Ch. 1 - A section of a composite wall with the dimensions...Ch. 1 - A section of a composite wall with the dimensions...Ch. 1 - Repeat Problem 1.35 but assume that instead of...Ch. 1 - 1.37 Mild steel nails were driven through a solid...Ch. 1 - Prob. 1.38PCh. 1 - 1.39 On a cold winter day, the outside wall of a...Ch. 1 - As a designer working for a major electric...Ch. 1 - 1.41 A heat exchanger wall consists of a copper...Ch. 1 - 1.43 A simple solar heater consists of a flat...Ch. 1 - A composite refrigerator wall is composed of 5 cm...Ch. 1 - An electronic device that internally generates 600...Ch. 1 - 1.47 A flat roof is modeled as a flat plate...Ch. 1 - A horizontal, 3-mm-thick flat-copper plate, 1-m...Ch. 1 - 1.49 A small oven with a surface area of is...Ch. 1 - A steam pipe 200 mm in diameter passes through a...Ch. 1 - 1.51 The inner wall of a rocket motor combustion...Ch. 1 - 1.52 A flat roof of a house absorbs a solar...Ch. 1 - Determine the power requirement of a soldering...Ch. 1 - 1.54 The soldering iron tip in Problem 1.53...Ch. 1 - Prob. 1.55PCh. 1 - A pipe carrying superheated steam in a basement at...Ch. 1 - Draw the thermal circuit for heat transfer through...Ch. 1 - 1.60 Two electric resistance heaters with a 20 cm...Ch. 1 - 1.63 Liquid oxygen (LOX) for the space shuttle is...Ch. 1 - The interior wall of a large, commercial walk-in...Ch. 1 - 1.67 In beauty salons and in homes, a ubiquitous...Ch. 1 - The heat transfer coefficient between a surface...Ch. 1 - The thermal conductivity of fibreglass insulation...Ch. 1 - 1.71 The thermal conductivity of silver at 212°F...Ch. 1 - 1.72 An ice chest (see sketch) is to constructed...Ch. 1 - Estimate the R-values for a 5-cm-thick fiberglass...Ch. 1 - A manufacturer in the United States wants to sell...Ch. 1 - Referring to Problem 1.74, how many kilograms of...Ch. 1 - 1.76 Explain a fundamental characteristic that...Ch. 1 - 1.77 Explain each in your own words. (a) What is...Ch. 1 - What are the important modes of heat transfer for...Ch. 1 - 1.79 Consider the cooling of (a) a personal...Ch. 1 - Describe and compare the modes of heat loss...Ch. 1 - A person wearing a heavy parka is standing in a...Ch. 1 - Discuss the modes of heat transfer that determine...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A long stainless-steel (AISI 316) steam pipe, with an inside diameter of 6.00 cm and an outside diameter of 8.00 cm, is covered with a layer of asbestos insulation (k = 0.150 W/m-K) 1.00 cm thick, which in turn is covered with foam insulation (k = 0.044 W/m-K) 6.00 cm thick. The inside surface temperature of the stainless-steel steam pipe is measured to be 250.0°C, while the outside surface of the foam is exposed to convection, T_inf = 25.0°C, h_inf = 15.0 W/m^2-K. • Draw and label a sketch of this system. Include dimensions, known temperatures, etc. • Draw and completely label the corresponding 1-D steady-state conduction resistor diagram. • Determine the heat transfer rate through the pipe per unit length. • Calculate the temperature at the asbestos/foam interface.arrow_forwardSteam at 235°C is flowing inside a steel pipe (k = 61 W/m ∙ °C) whose inner and outer diameters are 10 cm and 12 cm, respectively, in an environment at 20°C. The heat transfer coefficients inside and outside the pipe are 105 W/m2 ∙ °C and 14 W/m2 ∙ °C, respectively. Determine (a) the thickness of the insulation (k = 0.038 W/m ∙ °C) needed to reduce the heat loss by 95 percent and (b) the thickness of the insulation needed to reduce the exposed surface temperature of insulated pipe to 40°C for safety reasons.arrow_forward2. A 15-cm X 20-cm hot surface at 85°C is to be cooled by attaching 4 cm-long aluminum (k = 237 W/m-°C) fins of 2-mm X 2-mm square cross section. The temperature of surrounding medium is 25°C and the heat transfer coefficient on the surfaces can be taken to be 20 W/m2-°C. If it is desired to triple the rate of heat transfer from the bare hot surface, determine the number of fins that needs to be attached.arrow_forward
- Circular fins of uniform cross section, with diameter of 10 mm and length of 50 mm, are attached to a wall with surface temperature of 350°C. The fins are made of material with thermal conductivity of 240 W/m·K, and they are exposed to an ambient air condition of 25°C and the convection heat transfer coefficient is 250 W/m2·K. Determine the heat transfer rate and plot the temperature variation of a single fin for the following boundary conditions: (a) Infinitely long fin (b) Adiabatic fin tip (c) Fin with tip temperature of 250°C (d) Convection from the fin tiparrow_forward1. (a) Consider a room with a 1.8-m-high and 2.0-m-wide double-pane window consisting of two 4-mm-thick layers of glass separated by a 10-mm-wide stagnant air space. The convection heat transfer coefficients on the inner and outer surfaces of the window are 12 W/m2 K and 25 W/m2 K, respectively, while the average thermal conductivity of glass is 0.78 W/m K; and the air, 0.026 W/m K. If the room is maintained at 22 oC, the outside temperature is -4 oC and heat transfer due to radiation can be neglected, determine: (i) Draw the sketch and thermal resistance network; (ii) the total thermal resistance; (iii) the steady rate of heat transfer through this double-pane window; (iv) the temperature of the inner surface of the window.…arrow_forwardA 2-m × 1.8-m section of wall of an industrial furnace burning natural gas is not insulated, and the temperature at the outer surface of this section is measured to be 80°C. The temperature of the furnace room is 30°C, and the combined convection and radiation heat transfer coefficient at the surface of the outer furnace is 10 W/m2·C. It is proposed to insulate this section of the furnace wall with perlite insulation (k = 0.052 W/m·C) in order to reduce the heat loss by 90 percent, Assuming the outer surface temperature of the metal section still remains at about 80°C, determine the thickness of the insulation that needs to be used.arrow_forward
- A 50-meter-long cast iron pipe with a 10-centimeter outside diameter goes through a 288 K temperature open environment. The temperature of the pipe's outer surface is 423 K, and the combined heat transfer coefficient on the pipe's outside surface is 25 W/m2 K. Considering and stating the necessary assumptions determine, (5 marks) (a) The rate of heat loss from the pipe (b) The energy lost per year if the cost of the fuel is 0.52 $/therm ( 1 therm = 105,500 kJ) c) The thickness of the insulation if 98% of the energy loss is planned to be saved. Consider the conduction coefficient of the insulation is 0.035 W/mK.arrow_forwardPulverized coal particles are used in oxy-fuel combustion power plants for electricity generation. Consider a situation where coal particles are suspended in hot air flowing through a heated tube, where the convection heat transfer coefficient is 100 W/m2·K. If the average surface area and volume of the coal particles are 3.1 mm2 and 0.5 mm3, respectively, determine how much time it would take to heat the coal particles to two-thirds of the initial temperature difference.arrow_forwardIn a food industry, pieces of meat with approximately 30 cm in diameter and 20 mm in thickness are stored in a industrial freezer and thawed by exposure to ambient air at 15°C with convective heat transfer coefficient equal to 10W/(m2.K). Consider a piece of meat that, when removed from the freezer, had a temperature of -12°C. For defrosting, the piece is hung on a "line", so that both larger surfaces are exposed to the ambient air. For frozen meat, the following properties can be assumed ρ=1090 kg/m3, cp=3.54 kJ/(kg.K), k=0.47 W/(m.K). Ask: (1) Indicating the control volume and the simplifications adopted, obtain the differential energy balance equation for the cooling the piece of meat and describe the conditions of outline and initial that apply to the process, justifying them; (2) Use the appropriate analytical solution to determine the time necessary for the complete defrosting of the part. The part is considered to be completely thawed when a minimum temperature of 5oC is reached…arrow_forward
- Cold conditioned air at 12°C is flowing inside a 1.5-cm-thick square aluminum (k = 237 W/m·K) duct of inner cross section 22 cm * 22 cm at a mass flow rate of 0.8 kg/s. The duct is exposed to air at 33°C with a combined convection-radiation heat transfer coefficient of 13 W/m2·K. The convection heat transfer coefficient at the inner surface is 75 W/m2·K. If the air temperature in the duct should not increase by more than 1°C determine the maximum length of the duct.arrow_forwardA 50-meter-long cast iron pipe with a 10-centimeter outside diameter goes through a 288 K temperature open environment. The temperature of the pipe's outer surface is 423 K, and the combined heat transfer coefficient on the pipe's outside surface is 25 W/m2 K. Considering and stating the necessary assumptions determine,(a) The rate of heat loss from the pipe (b) The energy lost per year if the cost of the fuel is 0.52 $/therm ( 1 therm = 105,500 kJ) c) The thickness of the insulation if 98% of the energy loss is planned to be saved. Consider the conduction coefficient of the insulation is 0.035 W/mK.arrow_forwardIn a meat processing plant, 4 cm-diameter spherical meat balls (k=0.45 W/m-K and α=0.91×10-7 m²/s) that are initially at 25 °C are to be cooled by passing them through a refrigeration room at -10 °C. The heat transfer coefficient in the cold room is 22.5 W/m²-K. If surface of the meat balls is to be cooled to 3 °C, determine how long the meat balls should be kept in the refrigeration room. What will be the center temperature of the meat balls at the end of the process?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Understanding Conduction and the Heat Equation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=6jQsLAqrZGQ;License: Standard youtube license