FLUID MECHANICS-PHYSICAL ACCESS CODE
8th Edition
ISBN: 9781264005086
Author: White
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 1, Problem 1.59P
A solid cylinder of diameter D, length L, and density
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A cylinder of mass m slides down from rest in a vertical tube whose inner surface is covered by a viscous oil of film thickness h. If the diameter and height of the cylinder are D and L, respectively, derive an expression for the velocity of the cylinder as a function of time, t. Discuss what will happen as t → ∞. Can this device serve as a viscometer?
The block of weight W = 50 N is pulled by a weight W0 = 60 N along the surface of a table by means of an inextensible cable and a pulley. Between the block and the table there is a uniform layer of oil of viscosity m = 0.1 Pa-s and clearance h = 2 mm. The contact area is 0.01 m2. Find the terminal velocity U if the table is very long.
Oil (dynamic viscosity) between a block of mass M (5 kg) and the substrate(μ = 1.6 Pa.s), oil film thickness (h = 0.7 mm)). Block base surfaceIts area is given as A = 28 cm2. Block m (1kg weight) with a wire ropeIt depends on the mass. At time t = 0, mass m is released. According to these data;a) Find the viscous forces when the block moves with V = 1 m / s velocity.b) Derive an equation for the block velocity as a function of time (t).c) Plot the velocity-time variation for t = 0 and t = t.
Chapter 1 Solutions
FLUID MECHANICS-PHYSICAL ACCESS CODE
Ch. 1 - Prob. 1.1PCh. 1 - Table A.6 lists the density of the standard...Ch. 1 - For the triangular element in Fig, P1.3,show that...Ch. 1 - Sand, and other granular materials, appear to...Ch. 1 - The mean free path of a gas, l, is defined as the...Ch. 1 - Henri Darcy, a French engineer, proposed that the...Ch. 1 - Convert the following inappropriate quantities...Ch. 1 - Suppose we know little about the strength of...Ch. 1 - A hemispherical container, 26 inches in diameter,...Ch. 1 - The Stokes-Oseen formula [33] for drag force F on...
Ch. 1 - P1.11 In English Engineering units, the specific...Ch. 1 - For low-speed (laminar) steady flow through a...Ch. 1 - The efficiency ? of a pump is defined as the...Ch. 1 - Figure P1.14 shows the flow of water over a dam....Ch. 1 - The height H that fluid rises in a liquid...Ch. 1 - Algebraic equations such as Bernoulli's relation,...Ch. 1 - The Hazen-Williams hydraulics formula for volume...Ch. 1 - For small particles at low velocities, the first...Ch. 1 - In his study of the circular hydraulic jump formed...Ch. 1 - Books on porous media and atomization claim that...Ch. 1 - Aeronautical engineers measure the pitching moment...Ch. 1 - Prob. 1.22PCh. 1 - During World War II, Sir Geoffrey Taylor, a...Ch. 1 - Air, assumed to be an ideal gas with k = 1.40,...Ch. 1 - On a summer day in Narragansett, Rhode Island, the...Ch. 1 - When we in the United States say a car's tire is...Ch. 1 - Prob. 1.27PCh. 1 - Wet atmospheric air at 100 percent relative...Ch. 1 - Prob. 1.29PCh. 1 - P1.30 Repeat Prob. 1.29 if the tank is filled with...Ch. 1 - Prob. 1.31PCh. 1 - Prob. 1.32PCh. 1 - A tank contai as 9 kg of CO2at 20°C and 2.0 MPa....Ch. 1 - Consider steam at the following state near the...Ch. 1 - In Table A.4, most common gases (air, nitrogen,...Ch. 1 - Prob. 1.36PCh. 1 - A near-ideal gas has a molecular weight of 44 and...Ch. 1 - In Fig. 1.7, if the fluid is glycerin at 20°C and...Ch. 1 - Prob. 1.39PCh. 1 - Glycerin at 20°C fills the space between a hollow...Ch. 1 - An aluminum cylinder weighing 30 N, 6 cm in...Ch. 1 - Prob. 1.42PCh. 1 - Prob. 1.43PCh. 1 - One type of viscometer is simply a long capillary...Ch. 1 - A block of weight W slides down an inclined plane...Ch. 1 - A simple and popular model for two nonnewtonian...Ch. 1 - Data for the apparent viscosity of average human...Ch. 1 - A thin plate is separated from two fixed plates by...Ch. 1 - An amazing number of commercial and laboratory...Ch. 1 - Prob. 1.50PCh. 1 - Prob. 1.51PCh. 1 - The belt in Fig. P1.52 moves at a steady velocity...Ch. 1 - A solid tune of angle 2 , base r0, and density...Ch. 1 - A disk of radius R rotates at an angular velocity ...Ch. 1 - A block of weight W is being pulled over a table...Ch. 1 - The device in Fig. P1.56 is called a cone-plate...Ch. 1 - Extend the steady flow between a fixed lower plate...Ch. 1 - The laminar pipe flow example of Prob. 1.12 can be...Ch. 1 - A solid cylinder of diameter D, length L, and...Ch. 1 - Prob. 1.60PCh. 1 - Prob. 1.61PCh. 1 - P1.62 The hydrogen bubbles that produced the...Ch. 1 - Derive Eq. (1.33) by making a force balance on the...Ch. 1 - Pressure in a water container can be measured by...Ch. 1 - The system in Fig. P1.65 is used to calculate the...Ch. 1 - Prob. 1.66PCh. 1 - Prob. 1.67PCh. 1 - Prob. 1.68PCh. 1 - A solid cylindrical needle of diameter d, length...Ch. 1 - Derive an expression for the capillary height...Ch. 1 - A soap bubble of diameter D1coalesces with another...Ch. 1 - Early mountaineers boiled water to estimate their...Ch. 1 - A small submersible moves al velocity V, in fresh...Ch. 1 - Oil, with a vapor pressure of 20 kPa, is delivered...Ch. 1 - An airplane flies at 555 mi/h. At what altitude in...Ch. 1 - Prob. 1.76PCh. 1 - Prob. 1.77PCh. 1 - P1.78 Sir Isaac Newton measured the speed of sound...Ch. 1 - Prob. 1.79PCh. 1 - Prob. 1.80PCh. 1 - Use Eq. (1.39) to find and sketch the streamlines...Ch. 1 - P1.82 A velocity field is given by u = V cos, v =...Ch. 1 - Prob. 1.83PCh. 1 - In the early 1900s, the British chemist Sir Cyril...Ch. 1 - Prob. 1.85PCh. 1 - A right circular cylinder volume v is to be...Ch. 1 - The absolute viscosity of a fluid is primarily a...Ch. 1 - Prob. 1.2FEEPCh. 1 - Helium has a molecular weight of 4.003. What is...Ch. 1 - An oil has a kinematic viscosity of 1.25 E-4 m2/s...Ch. 1 - Prob. 1.5FEEPCh. 1 - Prob. 1.6FEEPCh. 1 - FE1.7 Two parallel plates, one moving at 4 m/s...Ch. 1 - Prob. 1.8FEEPCh. 1 - A certain water flow at 20°C has a critical...Ch. 1 - Prob. 1.10FEEPCh. 1 - Sometimes we can develop equations and solve...Ch. 1 - When a person ice skates, the surface of the ice...Ch. 1 - Two thin flat plates, tilted at an angle a, are...Ch. 1 - Oil of viscosity and density drains steadily...Ch. 1 - Prob. 1.5CPCh. 1 - Prob. 1.6CPCh. 1 - Prob. 1.7CPCh. 1 -
C1.8 A mechanical device that uses the rotating...Ch. 1 - Prob. 1.9CPCh. 1 - A popular gravity-driven instrument is the...Ch. 1 - Mott [Ref. 49, p. 38] discusses a simple...Ch. 1 - A solid aluminum disk (SG = 2.7) is 2 in in...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- C1 (a). A lubricating oil having the dynamic viscosity of 0.055 poise and kinematic viscosity of 0.17 stokes. Calculate (i) the density of oil in kg/m3, (ii) the weight density of oil in N/m3,(iii) the specific gravity, and (iv) the specific volume in m3/kg. C1 (b). Calculate the capillary effect in mm in a glass tube of 4.4 mm diameter, when immersed in (1) water (2) mercury. The values of surface tension in contact with air are 0.0737 N/m and 0.54 N/m respectively. The contact angle for water =00 and mercury =1300. (Enter only the values by referring to the unit given. Also, upload the handwritten answers in the link provided) C1(a).(i).The density of oil in kg/m3 C1(a). (ii) the weight density of oil in N/m3 C1(a). (iii) the specific gravity C1(a). (iv) the specific volume in m3/kg C1 (b). 1.The capillary effect (water) in mm C1 (b). 2.The capillary effect (mercury) in mmarrow_forwardSparky is on the university speed ice skating team. When crossing the finish line Sparky wants to show off and come across the finish line on one skate with a velocity of 35 ft/sec (V). Sparky weighs 150 lbf. Sparky’s weight is supported by a thin liquid film of water melted by the pressure of the skate blade. If the blade is 13 inches long and 0.125 inches wide estimate Sparky’s deceleration resulting from viscous shear in a water film of thickness of 0.0000575 inches (h). Neglect all end effects. Evaluate all properties at 32°F. Suggest creating a simple schematic of the problem using V, h, and the viscous shear stress (not required).arrow_forwardA piston 796 mm diameter and 200 mm long works in a cylinder of 800 mm diameter. If the annular space is filled with lubricating oil of viscosity 5 centipoise, calculate the speed of descent in m/s of the piston in vertical position. The weight of the piston and the axial load are 9.81N. (Choices: a) 6.12 b) 7.84 c) 10.56 d) 8.24)arrow_forward
- Calculate the power required per meter of width of stream to force lubricating oil through the gap between two horizontal flat plates under the following conditions: Distance between plates, 6 mm Flow rate of oil per meter of width, 100 m3h Viscosity of oil, 25 cP Density of oil, 0.88 g/cm3 Length of plates, 3 m Assume that the plates are very wide in comparison with the distance between them and that end effects can be neglected.arrow_forwardA low-altitude meteorological research balloon, temperature sensor, and radio transmitter together weigh 3.1 lb. When inflated with helium, the ballon is spherical with a diameter size of 5.5 feet. The volume of the trasmitter can be neglected when compared to the ballon's size. The ballon is released from ground level and quickly reaches its terminal ascent velocity. Neglecting variations in the atmosphere's density, how long does it take the ballon to reach an altitude of 1000ft?arrow_forwardAn air hockey puck has a mass of 50 g and is 9 cm in diameter. When placed on the air table, a 40 degrees C air film, of thickness 0.12 mm-thickness forms under the puck. a) Using Sutherlands law, what is the viscosity of the air? b) If the puck is travelling at 10 m/s, assuming a linear velocity profile, what is the force on the puck due to shear stress? c)What is the terminal velocity of the puck?arrow_forward
- A 10-in diameter plunger slides in a 10.006-in diameter cylinder, the annular space being filled with oil having a kinematic viscosity of 0.004 ft²/s and specific gravity of 0.85. If the plunger moves at 0.6 ft/s, find the frictional resistance when 9ft is engaged in the cylinder.arrow_forwardA propeller-driven aircraft has an in-flight weight of 4,105 lb (equivalent to a mass of 1,862 kg) and is cruising at a true airspeed of 120 kts. The lift-to-drag ratio of the aircraft is 8.2. If the propeller efficiency, ηp, is 0.8, then how much brake power is required for flight? Work through this problem in both USC and SI units.arrow_forwardA nuclear reactor is cooled by liquid sodium. The liquid sodium has the following properties: dynamic viscosity = 0.41 mPa·s, specific heat capacity = 1.2 kJ/kgK, thermal conductivity 82 W/mK. Which of the following statements is correct for this scenario? please explain A The thermal boundary layer is thicker than the hydraulic boundary layer. B Heat is transferred through the fluid more easily than momentum. C The velocity varies significantly from the surface to the thickness of the thermal boundary layer. D The hydraulic boundary layer is thicker than the thermal boundary layer.arrow_forward
- A sled with two runners slides along a thin horizontal layer of water between the ice and the runners. The horizontal force that the water puts on the runners is equal to 2.4 lb when the sled's speed is 50 ft/s. The total area of both runners in contact with the water is 0.04 ft2, and the viscosity of the water is 3.5x10 lbs/ft2. Determine the thickness of the water layer under the runners. Assume a linear velocity distribution in the water layer.arrow_forwardA passenger train, Keretapi Tanah Melayu (KTM) moves from A, to B at constant speed of 60 m/s. The long of the train is 15 m. By assuming the outer wall of the train is flat, air density, = 1.164 kg/m3 and air kinematic viscosity, = 1.60 x 10-5 m2 /s, determine at the back edge of the train (L = 15 m), boundary layer thickness, in meter (m) displacement thickness, * in meter (m), and iii. wall shear stress in Pascal (Pa).arrow_forwardThe pilot of a Boeing 767 determines that a total of 22,300 kilograms of jet fuel is needed to fly from Montreal to Edmonton. A floatstick check finds that there is 11,549 litres of fuel already in the tanks. How much fuel, expressed in litres, must be added to the tanks? The density of jet fuel varies with temperature. For the prevailing conditions take the density of the jet fuel to be 0.803 kg/L or equivalently 1.77 lb/L.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Unit Conversion the Easy Way (Dimensional Analysis); Author: ketzbook;https://www.youtube.com/watch?v=HRe1mire4Gc;License: Standard YouTube License, CC-BY