SHIGLEY'S MECHANICAL ENGR DESIGN (LL)
10th Edition
ISBN: 9781308945446
Author: BUDYNAS
Publisher: MCG/CREATE
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 1, Problem 31P
Generally, final design results are rounded to or fixed to three digits because the given data cannot justify a greater display. In addition, prefixes should be selected so as to limit number strings to no more than four digits to the left of the decimal point. Using these rules, as well as those for the choice of prefixes, solve the following relations:
(a) σ = M/Z, where M = 1770 lbf · in and Z = 0.934 in3.
(b) σ = F/A, where F = 9440 lbf and A = 23.8 in2.
(c) y = Fl3/3EI, where F = 270 lbf, l = 31.5 in, E = 30 Mpsi, and I = 0.154 in4.
(d) θ = Tl/GJ, where T = 9 740 lbf · in, l = 9.85 in, G = 11.3 Mpsi, and J = πd4/32 with d = 1.00 in.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A tentative rule was given about tipping in Testing Experiment Table 8.4, where if a vertical line passing through the object's center of mass is within the object's area of support the object does not tip. According to the rule, the full box of crackers in the following experiment, which has a width of 13 cm and a height of 20 cm, was seen to tip at an angle of: θc=tan−1(13 cm/20 cm)=33∘θ
According to the rule, at what angle will a box with the left half filled with crackers begin to tip? Assume the box is light-weight and that the contents remain in the configuration in
Determine the width and thickness of the leaves (in mm) of a leaf spring using the following specifications:
Total load = 140 kN;
Number of springs supporting the load = 4; Maximum number of leaves = 10;
Span of the spring = 1000 mm;
Permissible deflection = 80 mm;
Modulus of elasticity, E = 200 kN/mm2;
and allowable stress in spring material is 600 MPa.
Qsafe = 187.586 MJ
Chapter 1 Solutions
SHIGLEY'S MECHANICAL ENGR DESIGN (LL)
Ch. 1 - Select a mechanical component from Part 3 of this...Ch. 1 - Select a mechanical component from Part 3 of this...Ch. 1 - Select an organization listed in Sec. 16, go to...Ch. 1 - Go to the Internet and connect to the NSPE website...Ch. 1 - Go to the Internet and connect to the NSPE website...Ch. 1 - Estimate how many times more expensive it is to...Ch. 1 - The costs to manufacture a part using methods A...Ch. 1 - A cylindrical part of diameter d is loaded by an...Ch. 1 - When one knows the true values x1 and x2 and has...Ch. 1 - Use the true values x1 = 7 and x2 = 8 (a)...
Ch. 1 - A solid circular rod of diameter d undergoes a...Ch. 1 - A fatigue test is performed on rotating beam...Ch. 1 - Determinations of the ultimate tensile strength...Ch. 1 - The lives of parts are often expressed as the...Ch. 1 - The tensile 0.2 percent offset yield strength of...Ch. 1 - A mechanical system comprises three subsystems in...Ch. 1 - From See. 3-12, the maximum shear stress in a...Ch. 1 - A round cold-drawn 1045 steel rod has a mean...Ch. 1 - A beam subjected to axial loading will experience...Ch. 1 - Three blocks A, B, and C and a grooved block D...Ch. 1 - The volume of a rectangular parallelepiped is...Ch. 1 - A pivot in a linkage has a pin in the figure whose...Ch. 1 - A circular cross section O ring has the dimensions...Ch. 1 - Prob. 25PCh. 1 - Prob. 26PCh. 1 - Prob. 27PCh. 1 - Prob. 28PCh. 1 - Convert the following to appropriate ips units:...Ch. 1 - Convert the following to appropriate SI units: (a)...Ch. 1 - Generally, final design results are rounded to or...Ch. 1 - Repeal Prob. 1-31 for the following: (a) = F/wt,...Ch. 1 - Repeat Prob. 131 for: (a) = F/A, where A = d2/4, F...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The connection between an electric motor and a work machine shaft is achieved through a flanged rigid coupling where the torque is transmitted via coupling flanges. The power and rotational speed of the electric motor are determined using the last two digits of the student numbers, according to the formulas provided below. The coupling flanges are connected with three bolts of grade 5.6 with a 40 mm pitch circle diameter. The surface pressure endurance limit for the bolts is 16 MPa. The contact length between the bolt and the coupling flange is 12 mm. The coefficient of friction on the flange surfaces is 0.14, and the operating factor for the coupling is 0.8. The working conditions and material properties of the contact element are well-known, allowing for accurate force and stress analysis. (NO=35) a) Determine the bolt to be used in the coupling from the table. b) Draw the full sectional view of the used coupling. Power (N): N = NO [kW]Speed (n): n = NOx12 + 450 [rpm]arrow_forwardAt a temperature of 60°F, a 0.03-in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [E = 10,000 ksi; v = 0.32; α=α=12.5 x 10-6/°F] bar with a width of 3.0 in. and a thickness of 0.70 in. Bar (2) is a stainless steel [E = 28,000 ksi; v = 0.12; α=α=9.6 x 10-6/°F] bar with a width of 1.9 in. and a thickness of 0.70 in. The supports at A and C are rigid. Assume h1=3.0 in., h2=1.9 in., L1=27 in., L2=47 in., and Δ=Δ= 0.03 in. Determine(a) the lowest temperature at which the two bars contact each other.(b) the normal stress in the two bars at a temperature of 260°F.(c) the normal strain in the two bars at 260°F.(d) the change in width of the aluminum bar at a temperature of 260°F.arrow_forwardAt a temperature of 60°F, a 0.03-in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [E = 10,000 ksi; v = 0.32; α=α=12.5 x 10-6/°F] bar with a width of 3.0 in. and a thickness of 0.70 in. Bar (2) is a stainless steel [E = 28,000 ksi; v = 0.12; α=α=9.6 x 10-6/°F] bar with a width of 1.9 in. and a thickness of 0.70 in. The supports at A and C are rigid. Assume h1=3.0 in., h2=1.9 in., L1=27 in., L2=47 in., and Δ=Δ= 0.03 in. Determine:arrow_forward
- At a temperature of 60°F, a 0.05-in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [E = 10,000 ksi; v = 0.32; α=α=12.5 x 10-6/°F] bar with a width of 2.9 in. and a thickness of 0.80 in. Bar (2) is a stainless steel [E = 28,000 ksi; v = 0.12; α=α=9.6 x 10-6/°F] bar with a width of 1.9 in. and a thickness of 0.80 in. The supports at A and C are rigid. Assume h1=2.9 in., h2=1.9 in., L1=28 in., L2=42 in., and Δ=Δ= 0.05 in. Determine(a) the lowest temperature at which the two bars contact each other.(b) the normal stress in the two bars at a temperature of 255°F.(c) the normal strain in the two bars at 255°F.(d) the change in width of the aluminum bar at a temperature of 255°F. Determine the lowest temperature, Tcontact, at which the two bars contact each other.arrow_forwardP2 = 18.95 Psi T2 = 575 R W12 = 32.59 Btu Q12 = 0 Btuarrow_forwardConvert each of the following into scientific notation and into engineering notation: Scientific notation Engineering notation SI unit with prefix Example: 36,800W 3.68 × 104 W 36.8 ×103 W 36.8 kW a) 3427m b) 0.00456A c) 0.000984N d) 3100.0 × 102N e) 0.0114 × 104m f) 2205.2m g) 30.0 ×10-2s h) 0.0473s i) 650,502Pa j) 3.03 ×10-1A k) 1000 × 10-3Narrow_forward
- QUESTION FIVE (a) At a certain location, wind is blowing steadily at 10 m/s. Determine the mechanical energy of air per unit mass and the power generation potential of a wind turbine with 60-m-diameter blades at that location. Take the air density to be 1.25 kg/m3. (b) Consider an alcohol and a mercury thermometer that read exactly 0°C at the ice point and 100°C at the steam point. The distance between the two points is divided into 100 equal parts in both thermometers. Do you think these thermometers will give exactly the same reading at a temperature of, say, 60°C? Explain.(c) Determine the work required to deflect a linear spring with a spring constant of 70 kN/m by 20 cm from its rest position.arrow_forwardAssume that annual energy requirement of an industry is 20000 kWh . DETERMINE size of wind turbine that is required to be installed to meet the energy requirement . Following assumptions are taken into account for estimation Annual energy requirement - 20000 kWh Propeller type wind machine is used . Coefficient of performance -0.40 Wind speed at 15 meter height is 5 meter / sec ( if the turbine hub is placed at the height other than 15 meter , the wind speed should be estimated as shown in " vertical wind speed variation section Density of air - 1 kg / m Capacity factor -0.30arrow_forwardThe force-deflection relation of a steel helical spring used in an engine is found experimentally as F( x) = 200 x + 50 x2 + 10 x3, where the force (F) and deflection (x) are measured in pounds and inches, respectively. If the spring undergoes a steady deflection of 0.5 in. during the operation of the engine, determine the equivalent linear spring constant of the spring at its steady deflection.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Mechanical Calculations; Author: Mometrix Academy;https://www.youtube.com/watch?v=FiQw8fpUHMY;License: Standard youtube license