True or False: The LENGTHEN command doesn’t work with arcs.

Q: ]means the repair work done to keep the system in good working condition.

A: It is required to fill the blank

Q: Which of the following is not a type of adjustment to a dozer blade? Camber Pitch Tilt Angle

A: Option (a)  camber

Q: How much current is considered a lethal amount

A: While any amount of current over 10 milliamps (0.01 amp) is capable of producing painful to severe…

Q: True or False: The JOIN command requires that line segments must lie end to end with no gaps or…

A: The JOIN command joins similar objects to form a single unbroken object. The JOIN command combines a…

Q: Sharp countersinks to be used when working on a milling machine is a safety consideration while…

A: Countersinks -  Countersinks are conical holes cut in a manufacturing object or the tool that is…

Q: How to draw front view and top view of the following component

A: Orthographic Projection is a technique for drawing a three-dimensional object from various…

Q: Describe the energy transfers that take place in the following situation: A person starts a lawn…

A: Energy conversion: (1) When the person pulls the cord, the mechanical energy is transferred to the…

Q: What to do if a thermostat reading seems wrong

A: Given Data⇒Thermostat reading wrongProblem definition⇒Problem says What to do if a thermostat…

Q: ..... ..... will extend the life of the equipment

A: ................. Will extend the life of the equipment.

Q: True or False: Objects on a layer that is turned off can still be modified

A: The AutoCAD hides the objects present in a layer that is turned off. The objects are only hidden and…

Q: Describe how the system works

A: A hydraulic system is a drive technique in which energy is transferred from an electric motor to…

Q: g two (2) cylincer types:

A: 1. SINGLE ACTING CYLINDER 2.DOUBLE ACTING CYLINDER

Q: Controlling the Radiation of Heat.

A: Radiation of heat is defined as a loss through which heat from the system is radiated outside the…

Q: True or False: To move an object, you must always select the objectfirst and then start the MOVE…

A: The objects in an AutoCAD file can be selected before and after the MOVE command has started. For…

Q: Water is flowing thru the pipe set-up. What can be the v thru pipe 3 ?

A:

Q: Derive the statement is true or false

A: Given; Any thermodynamic cycle operating between two temperature limits is reversible if the product…

Q: How much change in the energy of wind will take place if blade length becomes 3 times? No Change 27…

A: Given data: Length of the blade (Lf) = 3L Need to determine the change in the energy of wind.

Q: what can be caused by excessive negative caster

A: Solution:

Q: يمكننا إدخال رقم صفحة من خالل 0 0 ( Footer Both Header and Footer > Header None of the above > O

A: In the Microsoft we can enter page number in the footer. Header

Q: minimum cllowasle deign dianet

A: Given; A solid circular shaft needs to be designed to transmit;Torque,T=50 N-mAllowable shear…

Q: having 6 links, which one of the following is the (b) Four ternary links and two binary links…

A:

Q: 3. What is the name of the mentioned angle of attack? a O critical angle of attack O The most…

A: Correct answer: zero lift angle of attack

Q: The shortest distance between a line and a point is achieved when? a) A line is drawn at 90 degrees…

A: Given  The shortest distance between a line and a point is achieved when? a) A line is drawn at 90…

Q: rance between an alloy that failed at a lo

A: (e) In materials science, weariness is the debilitating of a material brought about by cyclic…

Q: Explain the three controls of hazards.

A: To Explain: The 3 controls of Hazards. Explanation: Hazards: Anything that cause harm such that…

Q: means the repair work done to keep the system in good working condition.

A: we will discuss an activity/ process that is involved with work  done to keep the system in good…

Q: True or False: The OFFSET command cannot be used on closed objects

A: The OFFSET command is used to create parallel lines, parallel curves and concentric circles at a…

Q: rotor blades wind energy

A: In terms of performance and cost, the rotor blades are the most significant components of a…

Q: Dad with an angle of 10° and radius

A:

Q: What are Ball and socket connections

A: The ball and socket connection  also known as spheroid joint, is a type of joint in which the…

Q: True or False: The BREAK command requires two separate points when breaking a circle.

A: The BREAK command is used to break the selected object between two points.

Q: What is the purpose of the control cable.

A: Control cables are multi-conductor cables used for automation and instrumentation applications.…

Q: A cooling fan is connected to the driving motor by a V-belt. How many incheslong is the V-belt?

A: given:

Q: What is the temperature of low

A: Given; A carnot cycle is having an efficiency of;  ηcarnot=0.75  High temperature reservior;…

Q: e power output from

A: Need to calculate the power output.

Q: Where in the shop should a list of emergency telephone numbers be posted

A: The list of emergency numbers shall be posted at the entrance and exit of the shop so that people…

Q: e voltage is measured

A: For measurements of voltage voltmeter is used in solar cell

Q: Type of Manual control on scrap machine

A: A shaper machine is used for the machining of flat surfaces. It works in the forward stroke and the…

Q: Briefly explain what a pH probe is and how it works

A: A pH scale represents the acidic or alkaline nature of a substance. It is between 0 and 14 , where…

Q: Use methods of section for members BD, CD, and CE

A: Consider the given diagram and apply force equilibrium in a vertical diagram.   ∑Fv=0RAy+RF-400…

Q: The following multi-bar mechanism is used to raise the parking space of homes. Get a degree of…

A:

Q: True or False: Objects must actually touch each other for the TRIM command to work.

A: The TRIM command is a tool in AutoCAD software which is used to eliminate or cut off any selected…

Q: True or False: You can only use the REDO command immediately after using the UNDO command.

A: The UNDO command takes back the work in a drawing session whereas the REDO command will take the…

Q: 0..

A: given; Type of automatic control on scrap machine on given figure.

Q: Chain block pulley is connected to a crane and is used to lift Heavy objects manually Select one:…

A: A chain block is a mechanism used for lifting and lowering heavy loads via a chain and they are also…

Q: ar is allowed to follow spira he angle rotated by link A itude of Coriolis accelerat

A:

Q: Which of the following has multiple degrees of freedom? Option 3 O Option 1

A: Multi-degree-of-freedom (multi-DOF) systems are those in which the motion is described by two or…

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.