The excess material left on the product after compression molding is to be identified. Concept introduction: The cross-linking between the molecules take place because of heat and catalyst during the performing and molding process.

Question

Want to see more full solutions like this?

Answer 1

Question

Chapter 10, Problem 10.1Q

Interpretation Introduction

Interpretation: The excess material left on the product after compression molding is to be identified.

Concept introduction:

The cross-linking between the molecules take place because of heat and catalyst during the performing and molding process.

Expert Solution & Answer

Answer to Problem 10.1Q

The excess material left on the product after compression molding is flash.

Explanation of Solution

Compression molding is the molding process in which the plastic materials are formed by placing them into a cavity by heat and pressure.

The water molecules, gases, and other by-products are formed by the cross-linking reaction.

Such by-products are known as flash which is left on the product after compression molding.

Conclusion

The excess material that is left on the product after compression molding is flash which is to be removed in order to produce fine products.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 2

Question

Chapter 10, Problem 10.1Q

Interpretation Introduction

Interpretation: The excess material left on the product after compression molding is to be identified.

Concept introduction:

The cross-linking between the molecules take place because of heat and catalyst during the performing and molding process.

Expert Solution & Answer

Answer to Problem 10.1Q

The excess material left on the product after compression molding is flash.

Explanation of Solution

Compression molding is the molding process in which the plastic materials are formed by placing them into a cavity by heat and pressure.

The water molecules, gases, and other by-products are formed by the cross-linking reaction.

Such by-products are known as flash which is left on the product after compression molding.

Conclusion

The excess material that is left on the product after compression molding is flash which is to be removed in order to produce fine products.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 3

Question

Chapter 10, Problem 10.1Q

Interpretation Introduction

Interpretation: The excess material left on the product after compression molding is to be identified.

Concept introduction:

The cross-linking between the molecules take place because of heat and catalyst during the performing and molding process.

Expert Solution & Answer

Answer to Problem 10.1Q

The excess material left on the product after compression molding is flash.

Explanation of Solution

Compression molding is the molding process in which the plastic materials are formed by placing them into a cavity by heat and pressure.

The water molecules, gases, and other by-products are formed by the cross-linking reaction.

Such by-products are known as flash which is left on the product after compression molding.

Conclusion

The excess material that is left on the product after compression molding is flash which is to be removed in order to produce fine products.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 4

Question

Chapter 10, Problem 10.1Q

Interpretation Introduction

Interpretation: The excess material left on the product after compression molding is to be identified.

Concept introduction:

The cross-linking between the molecules take place because of heat and catalyst during the performing and molding process.

Expert Solution & Answer

Answer to Problem 10.1Q

The excess material left on the product after compression molding is flash.

Explanation of Solution

Compression molding is the molding process in which the plastic materials are formed by placing them into a cavity by heat and pressure.

The water molecules, gases, and other by-products are formed by the cross-linking reaction.

Such by-products are known as flash which is left on the product after compression molding.

Conclusion

The excess material that is left on the product after compression molding is flash which is to be removed in order to produce fine products.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 5

Chapter 10, Problem 10.1Q

Interpretation Introduction

Interpretation: The excess material left on the product after compression molding is to be identified.

Concept introduction:

The cross-linking between the molecules take place because of heat and catalyst during the performing and molding process.

Expert Solution & Answer

Answer to Problem 10.1Q

The excess material left on the product after compression molding is flash.

Explanation of Solution

Compression molding is the molding process in which the plastic materials are formed by placing them into a cavity by heat and pressure.

The water molecules, gases, and other by-products are formed by the cross-linking reaction.

Such by-products are known as flash which is left on the product after compression molding.

Conclusion

The excess material that is left on the product after compression molding is flash which is to be removed in order to produce fine products.

Answer 6

Chapter 10, Problem 10.1Q

Interpretation Introduction

Interpretation: The excess material left on the product after compression molding is to be identified.

Concept introduction:

The cross-linking between the molecules take place because of heat and catalyst during the performing and molding process.

Expert Solution & Answer

Answer to Problem 10.1Q

The excess material left on the product after compression molding is flash.

Explanation of Solution

Compression molding is the molding process in which the plastic materials are formed by placing them into a cavity by heat and pressure.

The water molecules, gases, and other by-products are formed by the cross-linking reaction.

Such by-products are known as flash which is left on the product after compression molding.

Conclusion

The excess material that is left on the product after compression molding is flash which is to be removed in order to produce fine products.

Answer 7

Chapter 10, Problem 10.1Q

Interpretation Introduction

Interpretation: The excess material left on the product after compression molding is to be identified.

Concept introduction:

The cross-linking between the molecules take place because of heat and catalyst during the performing and molding process.

Answer 8

Expert Solution & Answer

Answer to Problem 10.1Q

The excess material left on the product after compression molding is flash.

Answer 9

Expert Solution & Answer

Answer 10

Expert Solution & Answer

Answer 11

Explanation of Solution

Compression molding is the molding process in which the plastic materials are formed by placing them into a cavity by heat and pressure.

The water molecules, gases, and other by-products are formed by the cross-linking reaction.

Such by-products are known as flash which is left on the product after compression molding.

Answer 12

Conclusion

The excess material that is left on the product after compression molding is flash which is to be removed in order to produce fine products.

Answer 13

Ch. 10 - Prob. 10.1Q

The excess material left on the product after compression molding is to be identified. Concept introduction: The cross-linking between the molecules take place because of heat and catalyst during the performing and molding process.

Concept explainers

Interpretation: The excess material left on the product after compression molding is to be identified.

Concept introduction:

The cross-linking between the molecules take place because of heat and catalyst during the performing and molding process.

Answer to Problem 10.1Q

Explanation of Solution

Want to see more full solutions like this?

Chapter 10 Solutions

The excess material left on the product after compression molding is to be identified. Concept introduction: The cross-linking between the molecules take place because of heat and catalyst during the performing and molding process.

Concept explainers

Interpretation: The excess material left on the product after compression molding is to be identified. Concept introduction: The cross-linking between the molecules take place because of heat and catalyst during the performing and molding process.

Answer to Problem 10.1Q

Explanation of Solution

Want to see more full solutions like this?

Chapter 10 Solutions

Interpretation: The excess material left on the product after compression molding is to be identified.

Concept introduction:

The cross-linking between the molecules take place because of heat and catalyst during the performing and molding process.