Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 10, Problem 10ASRQ
After removing the vehicle’s hood in preparation for removing the engine: Technician A places the hood on the roof of the vehicle. Technician B sets the hood aside in a safe place on fender covers or cardboard. Who is correct?
- Technician A
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
An engine support fixture is used to hold the engine in place while removing a ______.
A. fwd transxle
B. rwd transmission
C. both
D . neither
Which of the following statements about unibodyconstruction is not true?a. A unibody is a stressed hull structure in whicheach of the body parts supplies structural supportand strength to the entire vehicle.b. Unibody vehicles tend to be tightly constructedbecause the major parts are all welded together.c. All unibodies are constructed from steel.d. Most front-wheel-drive unibody vehicles have acradle or partial frame.
Technician A uses sandpaper to remove carbon deposits from turbocharger wastegate parts. Technician B scrapes off heavy deposits before attempting to clean the unit. Who is correct?
Chapter 10 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 10 - WHat should be worn when working with any type of...Ch. 10 - Prob. 2RQCh. 10 - What is the best way to lift a vehicle when...Ch. 10 - True or False? The first step in removing an...Ch. 10 - Prob. 5RQCh. 10 - The buildup of minerals and deposits inside the...Ch. 10 - Hydrocarbon solvents are. flammable toxic both a...Ch. 10 - Prob. 8RQCh. 10 - Which cleaning method uses high-frequency sound...Ch. 10 - Parts must be when they go into an abrasive blast...
Ch. 10 - Prob. 11RQCh. 10 - Which of the following is not considered part of...Ch. 10 - Why should a memory saver be installed before dis...Ch. 10 - Which of the following statements is not true...Ch. 10 - Which of the following is not a common way to...Ch. 10 - While working on an engine with an excessive...Ch. 10 - While discussing the common causes for cracks...Ch. 10 - Technician A uses a crane to remove an engine from...Ch. 10 - Prob. 4ASRQCh. 10 - While discussing abrasive cleaners: Technician A...Ch. 10 - Technician A labels or marks all electrical wires...Ch. 10 - While discussing cleaning engine parts: Technician...Ch. 10 - While loosening the axle shaft hub nuts on a FWD...Ch. 10 - While preparing to remove an engine: Technician A...Ch. 10 - After removing the vehicles hood in preparation...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A uses a crane to remove an engine from its compartment- Technician B uses an engine cradle to remove an engine from its compartment Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile discussing the causes of extreme engine bearing damage Technician A says that contaminated and old engine oil could be the cause. Technician B says that a leaking radiator could be the cause. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhat is the best way to lift a vehicle when preparing to remove an engine? Frame contact hoist Drive on lift Hydraulic jack and safety stands Engine hoistarrow_forward
- While discussing the reasons for resurfacing a cylinder head; Technician A says it should be resurfaced to make it flat and very smooth so the head gasket can seal properly during engine assembly. Technician B says that it can be resurfaced to raise the compression. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhich of the following statements about unibody construction is not true? A unibody is a stressed hull structure in which each of the body parts supplies structural support and strength to the entire vehicle. Unibody vehicles tend to be tightly constructed because the major parts are all welded together. All unibodies are constructed from steel. Most front-wheel-drive unibody vehicles have a cradle or partial frame.arrow_forwardTechnician A says that some antitheft systems sound an alarm if someone enters the vehicle without a key Technician B says that some antitheft devices prevent the engine from starting. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- Technician A uses a blowgun to blow off parts during cleaning. Technician B uses a blowgun to clean off his uniform after working. Who is correct? Technician A Technician B Both A and B d. Neither A nor Barrow_forwardTechnician A makes sure that the exhaust system is cool to the touch before working on it. Technician B disconnects the batterys negative cable before welding an exhaust pipe. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardTrue or False? The first step in removing an engine is usually the removal of the intake and exhaust manifolds.arrow_forward
- Technician A says that used engine coolant should be collected and recycled. Technician B says that all oil- based waste materials can be collected in the same container if an approved waste disposal company is hired to rid the shop of the oil. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile preparing to remove an engine: Technician A turns the crankshaft pulley to set the engine at number 1 cylinder TDC. Technician B removes the drive belt and crankshaft pulley. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhat is the best way to lift a vehicle when preparingto remove an engine?a. Frame contact hoistb. Drive on liftc. Hydraulic jack and safety standsd. Engine hoistarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
General Industrial Safety; Author: Jim Pytel;https://www.youtube.com/watch?v=RXtF_vQRebM;License: Standard youtube license