Welding: Principles and Applications (MindTap Course List)
8th Edition
ISBN: 9781305494695
Author: Larry Jeffus
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 10, Problem 10R
In the pulsed-arc metal transfer current cycle, what is the term used to describe how the electric current in a transformer takes a few milliseconds to build up the magnetic field to full strength once the coil is energized?
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
How are plasma cutting equipment classified? Enumerate, define each one.
What types of metals can be cut by plasma cutting equipment? Enumerate and define each.
1)a) Why is automation of the covered electrode arc source difficult?b) what properties is a metal with good resistance welding ability expected to have?c) Why is the heat transfer factor higher in arc welding processes with the consumed electrode than the methods used with the non-consumed electrode?d) Why is it important to weld thin and long instead of thick and short?e) why is it important that the source root is designed to be forced to press, not pull?
2) there is a characteristic liquid penetration error on a large piece of steel poured in the sand mold. The surface of the piece consists of a mixture of sand and metal.a) Explain at least 3 of the steps that can be taken to correct this error.b) what other types of casting errors may possibly occur in each of these steps? Explain
3) grain structure formed in part after casting;a) Describe by drawing a figure.b) what problems can this grain structure pose? Please explain. How can these problems be cured?4) explain two of the…
Chapter 10 Solutions
Welding: Principles and Applications (MindTap Course List)
Ch. 10 - Why is usage of the term GWW preferable to MIG for...Ch. 10 - Using Table 10-1, answer the following: a. What...Ch. 10 - What factors must be considered when selecting...Ch. 10 - In short-circuiting transfer, what type of current...Ch. 10 - Describe the globular transfer process.Ch. 10 - In what form is metal transferred across the arc...Ch. 10 - What three conditions are required for the spray...Ch. 10 - Using Table 10-3, answer the following: a. What...Ch. 10 - Describe the current produced by the pulsed-arc...Ch. 10 - In the pulsed-arc metal transfer current cycle,...
Ch. 10 - List five advantages of the modulated current and...Ch. 10 - What is the difference between the wire melting...Ch. 10 - Using Figure 10-13, what is the approximate...Ch. 10 - Using Table 10-6, what would the amperage be for...Ch. 10 - The shielding gas selected can affect what...Ch. 10 - What may happen if the GMA welding electrode is...Ch. 10 - What effect does shortening the electrode...Ch. 10 - Describe the weld produced by a forehand welding...Ch. 10 - Describe the weld produced by a backhand welding...Ch. 10 - What components make up a GMA welding system?Ch. 10 - Why must GMA welders have a 100 duty cycle?Ch. 10 - What can happen if rollers of the wrong shape are...Ch. 10 - Where is the drive motor located in a pull-type...Ch. 10 - How is the wire-feed speed changed with a linear...Ch. 10 - What type of liner should be used for aluminum...Ch. 10 - What parts of a typical GMA welding gun can...Ch. 10 - Describe the spot welding process using a GMA...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Describe the current produced by the pulsed-arc metal transfer mode.arrow_forwardIn short-circuiting transfer, what type of current alloys the liquid metal at the electrode tip to be transferred by direct contact with the molten weld pool?arrow_forwardHow are high-power plasma torches cooled?arrow_forward
- Using Table 10-3, answer the following: a. What should the wire-feed speed and voltage ranges be to weld 1/8-in. (3 mm) metal with 0035-in. (0.90-mm) wire using argon shielding gas? b. What should the amperage and voltage range be using 98Ar+2%O2 to weld 1/4-in. (6-mm) metal with 0.045-in. (1.2-mm) wire?arrow_forwardWhat indicates that you have overheated the solder flux on copper?arrow_forwardList the four common variations of the conventional plasma cutting process and describe the benefits of each.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Understanding Conduction and the Heat Equation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=6jQsLAqrZGQ;License: Standard youtube license