(a)
Interpretation:
The conversion factor should be written to perform the given conversion.
An energy given in calories to its equivalent in joules.
Concept Introduction:
A conversion factor is a numerical ratio which is used to show a measurement in one unit as another unit. It is always equal to 1.
(b)
Interpretation:
The conversion factor should be written to perform the given conversion.
An energy given in joules to its equivalent in calories.
Concept Introduction:
A conversion factor is a numerical ratio which is used to show a measurement in one unit as another unit. It is always equal to 1.
(c)
Interpretation:
The conversion factor should be written to perform the given conversion.
An energy given in calories to its equivalent in kilocalories.
Concept Introduction:
A conversion factor is a numerical ratio which is used to show a measurement in one unit as another unit. It is always equal to 1.
(d)
Interpretation:
The conversion factor should be written to perform the given conversion.
An energy given in kilojoules to its equivalent in joules.
Concept Introduction:
A conversion factor is a numerical ratio which is used to show a measurement in one unit as another unit. It is always equal to 1.
Want to see the full answer?
Check out a sample textbook solutionChapter 10 Solutions
Introductory Chemistry: A Foundation
- What are the differentiating factors between potential and kinetic energy? a.Properties-physical or chemical b.State-solid or liquid c.Temperature-high or low d.Activity-in motion or in storagearrow_forwardClassify each of the following changes as endothermic or exothermic with respect to the italicized object: a cooling a beer; b burning leaves; c cooking a hamburger.arrow_forwardA book is held 6 feet above the floor and then dropped. Which statement is true? a.The potential energy of the book is converted to kinetic energy. b.The potential energy of the book is destroyed. c.Kinetic energy is created. d.The total energy of the system will not be conserved.arrow_forward
- A particulate-level illustration of the reaction AB+CDAD+CB is shown below. a Identify the reactants and products in this reaction. b Is the change shown chemical or physical? c Is the mass of the product particles less than, equal to, or greater than the mass of the reactant particles? d If the reaction takes place in a container that allows no energy to enter or leave, how does the total energy in the container after the reaction compare with the total energy in the container before the reaction?arrow_forwardAs a child plays on a swing, at what point in her movement is her kinetic energy the greatest? At what point is potential energy at its maximum?arrow_forwardDuring a recent winter month in Sheboygan, Wisconsin, it was necessary to obtain 3500 kWh of heat provided by a natural gas furnace with 89% efficiency to keep a small house warm (the efficiency of a gas furnace is the percent of the heat produced by combustion that is transferred into the house). (a) Assume that natural gas is pure methane and determine the volume of natural gas in cubic feet that was required to heat the house. The average temperature of the natural gas was 56 F; at this temperature and a pressure of 1 atm, natural gas has a density of 0.68 1 g/L. (b) How many gallons of LPG (liquefied petroleum gas) would be required to replace the natural gas used? Assume the LPG is liquid propane [ C3H8 : density, 0.5318 g/mL; enthalpy of combustion, 2219 Id/mo for the formation of CO2(g) and H2O(l) ] and the furnace used to burn the LPG has the same efficiency as the gas furnace. (c) What mass of carbon dioxide is produced by combustion of the methane used to heat the house? (d) What mass of water is produced by combustion of the methane used to heat the house? (e) What volume of air is required to provide the oxygen for the combustion of the methane used to heat the house? Air contains 23% oxygen by mass. The average density of air during the month was 1.22 g/L. (f) How many kilowatt—hours ( 1kWh=3.6106 J) of electricity would be required to provide the heat necessary to heat the house? Note electricity is 100% efficient in producing heat inside a house. (g) Although electricity is 100% efficient in producing heat inside a house, production and distribution of electricity is not 100% efficient. The efficiency of production and distribution of electricity produced in a coal-fired power plant is about 40%. A certain type of coal provides 2.26 kWh per pound upon combustion. What mass of this coal in kilograms will be required to produce the electrical energy necessary to heat the house if the efficiency of generation and distribution is 40%?arrow_forward
- Chemistry: The Molecular ScienceChemistryISBN:9781285199047Author:John W. Moore, Conrad L. StanitskiPublisher:Cengage LearningChemistry for Today: General, Organic, and Bioche...ChemistryISBN:9781305960060Author:Spencer L. Seager, Michael R. Slabaugh, Maren S. HansenPublisher:Cengage LearningIntroductory Chemistry: An Active Learning Approa...ChemistryISBN:9781305079250Author:Mark S. Cracolice, Ed PetersPublisher:Cengage Learning
- General Chemistry - Standalone book (MindTap Cour...ChemistryISBN:9781305580343Author:Steven D. Gammon, Ebbing, Darrell Ebbing, Steven D., Darrell; Gammon, Darrell Ebbing; Steven D. Gammon, Darrell D.; Gammon, Ebbing; Steven D. Gammon; DarrellPublisher:Cengage LearningChemistry & Chemical ReactivityChemistryISBN:9781337399074Author:John C. Kotz, Paul M. Treichel, John Townsend, David TreichelPublisher:Cengage LearningIntroductory Chemistry: A FoundationChemistryISBN:9781337399425Author:Steven S. Zumdahl, Donald J. DeCostePublisher:Cengage Learning