Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 10, Problem 2MC
To determine
The incorrect statement amongst the give statements.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Which of the following is part of the sprung weight ofa vehicle?a. Steering linkageb. Tiresc. Engined. All of the above
Technician A says the front wheel bearings on a typical FWD car are sealed and non-adjustable. Technician B says the front wheel bearings on a typical FWD car are greaseable and adjustable. Who is correct?
Technician A says that on FWD vehicles, the front wheels toe-out while the rear wheels on an independent suspension try to toe-in as the vehicle moves ahead. Technician B says that on RWD vehicles, the front wheels tend to toe-in while the rear wheels toe-out in response to rolling resistance as suspension compliance. Who is correct?
Chapter 10 Solutions
Automotive Technology
Ch. 10 - WHat should be worn when working with any type of...Ch. 10 - Why should a memory saver be installed before dis...Ch. 10 - Prob. 1TFCh. 10 - True or False? The first step in removing an...Ch. 10 - Prob. 3TFCh. 10 - What is the best way to lift a vehicle when...Ch. 10 - Prob. 2MCCh. 10 - The buildup of minerals and deposits inside the...Ch. 10 - Hydrocarbon solvents are. flammable toxic both a...Ch. 10 - Which cleaning method uses high-frequency sound...
Ch. 10 - Parts must be when they go into an abrasive blast...Ch. 10 - Prob. 7MCCh. 10 - Which of the following is not considered part of...Ch. 10 - Which of the following statements is not true...Ch. 10 - Which of the following is not a common way to...Ch. 10 - While working on an engine with an excessive...Ch. 10 - While discussing the common causes for cracks...Ch. 10 - Technician A uses a crane to remove an engine from...Ch. 10 - Prob. 4ASRQCh. 10 - While discussing abrasive cleaners: Technician A...Ch. 10 - Technician A labels or marks all electrical wires...Ch. 10 - While discussing cleaning engine parts: Technician...Ch. 10 - While loosening the axle shaft hub nuts on a FWD...Ch. 10 - While preparing to remove an engine: Technician A...Ch. 10 - After removing the vehicles hood in preparation...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says that the use of firmer, urethane bushings in the suspension improves the vehicles road-holding ability and handling. Technician B says that firmer bushings help eliminate torque steer in some FWD vehicles. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhich of the following statements about unibody construction is not true? A unibody is a stressed hull structure in which each of the body parts supplies structural support and strength to the entire vehicle. Unibody vehicles tend to be tightly constructed because the major parts are all welded together. All unibodies are constructed from steel. Most front-wheel-drive unibody vehicles have a cradle or partial frame.arrow_forwardTechnician A says that the suspension switch must be turned off before raising any corner of a car with an electronic air suspension. Technician B says that the ignition switch must not be turned on while any corner of a car with electronic air suspension is raised. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- Which of the following is part of the sprung weight of a vehicle? a. Steering linkage b. Tires c. Engine d. All of the abovearrow_forwardWhich of the following statements about seat belt retractors is not true? They stow away the scat belts when they are not being used. They allow freedom of movement for the occupant of the seat. They can tighten up and pull the occupant back during a crash. On some vehicles, they work in concert with the air bag system.arrow_forwardTechnician A says that a seized shift linkage may cause the transfer case to operate only in 4WD. Technician B says that a worn and loose linkage may cause a transfer case to operate only in 2WD. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- SLA systems in common use today are used in the ____ . a. coil spring suspension b. torsion bar suspension c. strut and control arm suspension d. all of the abovearrow_forwardTechnician A says that each ABS has its own diagnostic procedure involving use of the brake and antilock warning lamps, special testers, breakout boxes, scan tools, troubleshooting charts, and wiring diagrams. Technician B says that ABSs vary in the number of codes they can store and whether they will retain the code in memory when the ignition is turned off. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardTechnician A says that the module assembly will disarm the air bag system if certain faults occur. Technician B says the passenger side air bag may be turned off if there is not enough weight on the passenger seat. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forward
- What may be caused by improper engine and transmission mounts on FWD vehicles?arrow_forwardWhat results from having different axle ratios on thefront and rear of a 4WD vehicle when it is operatingin 4WD?a. Poor handling on dry surfacesb. Driveline windupc, Mechanical damage to the drivelined. All of the abovearrow_forwardWhat is a suspension system.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,